Commit graph

6 commits

Author SHA1 Message Date
Rai Harninder
ed2530d096 armv8/ls2080ardb: Enable VID support
This patch enable VID support for ls2080ardb platform.
It uses the common VID driver.

Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:24 -07:00
Wenbin Song
1be8d10be4 freescale: vid: Return i2c mux to default channel
IR chip is on one of the channels on multiplexed I2C-bus.
Reset to default channel after accessing.

Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-21 12:42:15 -07:00
Ying Zhang
2f66a828f7 powerpc/board/t4240rdb: Enable VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:38:05 -08:00
Ying Zhang
cabe4d2f19 board/freescale/common: Check IR chip mode for VID support
IR chip on all the boards are required to be used in Intel mode
to support VID. VDD will not be adjusted if IR chip is used in
other modes.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:37:03 -08:00
Shaohui Xie
02b5d2ed86 armv8/ls1043aqds: add LS1043AQDS board support
LS1043AQDS Specification:
-------------------------
Memory subsystem:
 * 2GByte DDR4 DIMM
 * 128 Mbyte NOR flash single-chip memory
 * 512 Mbyte NAND flash
 * 16 Mbyte high-speed SPI flash
 * SD connector to interface with the SD memory card

Ethernet:
 * Two RGMII ports
 * XFI 10G port
 * SGMII
 * QSGMII with 4x 1G ports

PCIe: supports Gen 1 and Gen 2

SATA 3.0: one SATA 3.0 port

USB 3.0: two micro AB connector and one type A connector

UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-11-30 09:11:10 -08:00
Ying Zhang
3ad2737ee3 powerpc/t208xqds: VID support
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00