Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Change has been done across the whole tree only zynqmp-mini-qspi hasn't
been fixed.
Origin changed done by commit ffd4c7c2ec
("dts: switch spi-flash to jedec, spi-nor compatible")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added alias for usb node in dts file.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This node is used by qspi driver for supporting qspi boot mode in SPL.
Similar changes have beeen done by commit a9022b017a
("ARM64: zynqmp: Add u-boot,dm-pre-reloc to clk nodes")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The SPL device tree is missing the entires for gpio1, uart1, usdhc1 and
usdhc2. This creates the missing imx6q-logicpd-u-boot.dtsi file
which will enable these functions so SPL can properly setup UART, detect
microSD card, and startup.
Fixes: 8f4691e31a ("ARM: imx6q_logic: With SPL_OF_CONTROL enabled,
remove MMC init")
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch restores commit c49d0ac38a ("ARM: dts: rmobile: Increase off-on
delay on the SD Vcc regulator"), which was accidentally dropped during DT
resync in commit 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with
Linux 5.0").
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fixes: 317d13ac63 ("ARM: dts: rmobile: Synchronize Gen3 DTs with Linux 5.0")
Tinker board needs to mux all the sdmmc gpio and
activate the regulator connected to bank 7. Remove
all the bank that are not in use and mark them as dm,spl
so-that it would initialize at SPL.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
According to the latest am572x[1] and dra74x[2] data manuals, mmc3
default, hs, sdr12 and sdr25 modes use iodelay values given in
MMC3_MANUAL1. Set the MODE_SELECT bit for these so that manual mode is
selected and correct iodelay values are configured.
[1] http://www.ti.com/lit/ds/symlink/am5728.pdf
[2] http://www.ti.com/lit/ds/symlink/dra746.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add device tree from Linux for driver model conversion
and enable OF_CONTROL. This will remove the following compile
warning:
==================================================
Device Tree Source is not correctly specified.
Please define 'CONFIG_DEFAULT_DEVICE_TREE'
or build with 'DEVICE_TREE=<device_tree>' argument
===================================================
Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Add the device-tree structure describing the MUX in board dts.
QDS board has an on-board RGMII PHY and 4 slots for extension cards.
All these can be accessed over MDIO through a MDIO MUX controlled
over I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add nodes for the Aspeed SD controllers with their necessary properties.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Implicitly Marvell MDIO driver uses DT node names for devices, but in this
case that is not unique. Set MDIO device names for master/slave to
cpm/cps.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alignment with kernel patch proposal for binding:
[PATCH v4 0/8] stm32 m4 remoteproc on STM32MP157c
https://lkml.org/lkml/2019/5/14/159
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Due to kernel DT alignment, pwr-supply is renamed to vdd-supply
and is a subnode of pwr-regulators.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As for Audio codec IC, HDMI IC is not "IO safe".
HDMI regulators (v3v3 and v1v2) must be enabled to allow
I2C1 bus usage. HDMI IC must be under reset during power up
and keep HDMI and AUDIO devices in reset while they are not
used in U-Boot to keep them in low power mode
(each device can be kept in reset independently keeping their
power supplies ON until kernel).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Avoid U-Boot auto-boot interruption for line break detection
on console when the RX line connected to STLINK is floating
(-IO error in getc cause by framing error and testc return 1)
Same workaround is applied on all the STMicroelectonics board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The pre-relocation probe is needed to reserve video frame buffer
in video_reserve() for all the board;
LDTC must be tagged prereloc in SOC U-Boot dtsi file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add node in DT and avoid error to search UCLASS_SYSRESET in
board_f.c::print_resetinfo() and lost 1.6s in U-Boot
for the trusted boot chain.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds independent watchdog support for stm32mp157c
in SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- Change DQSGE to 1 for DDR3, to cure missing DQS preamble.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to U-Boot by
me when I blindly copied the device tree from Linux.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
According to rock64 schemetic, both VCC_HOST1_5V and VCC_HOST_5V are
controlled by USB20_HOST_DRV(GPIO0A2), fix it so that we can get correct
power supply for USB HOST ports.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB host support on GR Peach board.
To use USB host on GR Peach, it might be necessary to solder JP3 header
onto the board first and then short it. Shorting JP3 is mandatory to let
the U5 regulator to supply VBUS to the CN3 USB port.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Add the pcf2127-rtc node under the i2c0->i2c-mux@77->i2c@3 for ls1088aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This patch adds some slave nodes to support the i2c dm on the device
side under the i2c0 controller.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls1088a, there are four I2C controllers. So add all I2C node
for ls1088a in device tree.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the ds3232-rtc node under the i2c0->i2c-mux@77->i2c@0 for ls2088aqds
boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
One ls2088a, there are four I2C controllers. So add I2C nodes in dts
for ls2088a.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add the pcf2127-rtc node under the i2c1 in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add pca9547 node to support i2c multiplexer under the i2c0 controller
in dts for ls1028aqds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add some slave nodes to support the i2c dm on the device side under the i2c0.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
