Add support for io-mode transfers. This is necessary for UBIFS to work
properly with spi-nor devices. The driver will work in IO mode when
"has-io-mode" is passed from device tree instead of DMA.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20220825125906.11581-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per driver model we should enumerate plat structure only in
of_to_plat() and should be used only in probe(). Copy required
plat structure info into priv structure in probe() and use priv
structure across the driver. So replace plat with priv structure across
the driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_read_id we are using STIG mode to read flash id's.
Call cadence_qspi_apb_command_read_setup() to setup cmd, addr and data
bus width properly before cadence_qspi_apb_command_read().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-3-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In cadence_spi_probe, cadence_qspi_versal_flash_reset() is called to reset
the flash device. Looks like there is a mistake in previous series of
patches where it is defined as cadence_spi_versal_flash_reset() but
called as cadence_qspi_versal_flash_reset. Since there is a weak function
defined with the same name this issue was not caught.
Fix the issue by renaming cadence_spi_versal_flash_reset as
cadence_qspi_versal_flash_reset().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220824113847.7482-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Check snprintf() return value for errors.
Make microblaze_cpu_get_desc() directly return snprintf() error code if
ret < 0. Otherwise, if the return value is greater than or equal to size,
the resulting string is truncated, so return -ENOSPC.
Fixes: 816226d27e ("cpu: add CPU driver for microblaze")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220829170205.1274484-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The drivers informs the user that a post config was not run after FPGA
configuration. This message is unnecessary in SPL because the
ps7_post_config function is called via spl_board_prepare_for_boot
function before jump_to_image_no_args function from board_init_r
function.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220808145331.24723-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Move arm twd timer driver from zynq to generic location.
DM timer drivers are designed differently to original driver. Timer is
counting up and not down.
Information about clock rates are find out in timer_pre_probe() that's
why there is no need to get any additional information from DT in the
driver itself (only register offset).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Link: https://lore.kernel.org/r/20220805061629.1207-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
We can check if the message was acknowledged in the common
ti_sci_do_xfer() which lets us remove it from after each call to this
function. This simplifies the code and reduces binary size.
Signed-off-by: Andrew Davis <afd@ti.com>
The inline hint is not needed here, the compiler will do the right thing
based on if we are compiling for speed or for code size. In this case the
inline causes this function to be placed inside each callsite which is
not the right thing to do for either speed nor size. There is no
performance benefit to this due to the larger function size reducing
cache locality, but there is a huge size penalty. Remove inline keyword.
Signed-off-by: Andrew Davis <afd@ti.com>
We don't need to print the same message in every location, just
print it in the function that fails and remove all the extra
message printouts.
Signed-off-by: Andrew Davis <afd@ti.com>
This ti_sci_do_xfer() function already prints out the reason for the
failure, and the caller of each of these functions should also notify
the user of the failed task. Remove this extra level of error message.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently for all Qcom SoCs/boards there are separate compatibles for
GPIO and pinctrl. But this is inconsistent with official (upstream) Linux
bindings which requires only a single compatible "qcom,<SoC name>-pinctrl"
and there is no such compatible property as "qcom,tlmm-<SoC name>".
So fix this inconsistency for Qcom SoCs in order to comply with upstream
DT bindings. This is done via removing compatibles from "msm_gpio" driver
and via binding to "msm_gpio" driver from pinctrl driver in case
"gpio-controller" property is specified for pinctrl node.
Suggested-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
With GPIO LV/MV subtype available, add "qcom,pms405-gpio" compatible
which requires support for GPIO MV subtype.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Since the base functionality remains the same for a reset driver on Qcom
SoCs, so leverage that to convert ipq4019 specific reset driver to a
generic Qcom reset driver. With that one just need to provide SoC specific
reset table.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
QCS404 SoC supports two types of PHY, one supports high speed mode or
USB2 PHY and the other supports super speed mode or USB3 PHY. So add
corresponding PHY drivers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Re-sync again on some linux part, add some fixes for fsl_elbc from
Pali and switch
imx8mn bsh to use nand base ident
For nand subsystem tested on:
- imx8mn Macronix MX30LF4G18AC
- P2020 based board Turris 1.1 for fsl_elbc
The gpio-button driver depends on DM_GPIO, add it to Kconfig to avoid
build errors.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Add timer support for Kirkwood and MVEBU devices.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
During compilation gcc throws warning:
drivers/mtd/nand/raw/fsl_elbc_nand.c: In function ‘fsl_elbc_nand_probe’:
drivers/mtd/nand/raw/fsl_elbc_nand.c:841:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return fsl_elbc_chip_init(0, (void *)dev_read_addr(dev), dev);
^
Fix it by using dev_read_addr_ptr() function which returns pointer instead
of dev_read_addr() which returns integer type.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Subpage write support for freescale eLBC NAND controller driver is
implemented in U-Boot and was fixes in the commit d3963721d9 ("nand: Sync
with Linux v4.1").
So remove NAND_NO_SUBPAGE_WRITE flag from the fsl_elbc_nand.c driver. This
partially revert commit cb04c77234 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE
to eLBC and IFC drivers"), only eLBC driver part.
With this change U-Boot with default settings can read from NAND UBIFS
image created on Linux with Linux default settings. Prior this change
U-Boot was unable to read from NAND UBIFS images created with Linux default
settings due to differnet UBI geometry.
Linux kernel fsl_elbc_nand.c driver also does not set NAND_NO_SUBPAGE_WRITE
flag and has implemented subpage write support.
Fixes: cb04c77234 ("nand/fsl: add NAND_NO_SUBPAGE_WRITE to eLBC and IFC drivers")
Fixes: d3963721d9 ("nand: Sync with Linux v4.1")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-By: Michael Trimarchi<michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8fc82d456e40a0.
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7bb427990ee364.
Rename the function to match this new behavior.
NOTE: fix nand_detect/nand_get_flash_type parameters in
mxs_nand_spl. This code seems never executed by any board
as alternative for nand detect
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 4722c0e958e636.
The returned "type" is never used in nand_scan_ident() and spl code
Make nand_get_flash_type() simply return an integer value in order
to avoid unnecessary ERR_PTR/PTR_ERR dance.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 8cfb9ab68f9070.
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
The kmtegr1 board is out of maintenance and can be removed. As it is the
only board in the tree using MPC8309 the support for this CPU is dropped
completely.
Signed-off-by: Holger Brunck <holger.brunck@hitachienergy.com>
The deadline for DM_ETH migration passed 2 years ago. Now that
platforms which cannot be migrated have been either removed or had
drivers disabled, and platforms that needed minor help to migrate have
been forcefully migrated, we can complete the migration.
This entails select'ing DM_ETH under NETDEVICES, and then removing now
extraneous depends on lines. In a few places, we can now either remove
options or just simplify later dependencies.
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
As this driver has been converted to DM_ETH and the migration deadline
is 2 years passed, remove the legacy code and callers.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
When using DM_ETH, which should be the default now, we need to always
have DM_MDIO and FSL_LS_MDIO enabled, so select them.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Wasim Khan <wasim.khan@nxp.com>
Cc: Udit Agarwal <udit.agarwal@nxp.com>
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Manish Tomar <Manish.Tomar@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver has not been converted to DM_ETH. The migration
deadline passed 2 years ago.
Cc: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This driver has not been converted to DM_ETH. The migration deadline
passed 2 years ago.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
This converts the following to Kconfig:
CONFIG_FSL_NGPIXIS
CONFIG_SYS_FSL_QMAN_V3
CONFIG_SYS_FSL_RAID_ENGINE
CONFIG_SYS_FSL_RMU
CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
CONFIG_SYS_FSL_SRIO_LIODN
CONFIG_SYS_FSL_TBCLK_DIV
CONFIG_SYS_FSL_USB1_PHY_ENABLE
CONFIG_SYS_FSL_USB2_PHY_ENABLE
CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
And we remove the entries from the README for a number of already
converted items.
Signed-off-by: Tom Rini <trini@konsulko.com>
In generally it is not permitted to implement an ofnode function only for
flat tree or live tree. Both must be supported. Also the code for
live tree access should be in of_access.c rather than ofnode.c which is
really just for holding the API-conversion code.
Update ofnode_write_prop() accordingly and fix the test so it can work
with flat tree too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these to VESA, itself an abbreviation, to avoid a conflict with
Verified Boot for Embedded.
Rename this to avoid referencing VBE.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 44645f87de ("mmc: Fix mmc_switch excessive timeout") introduced
a side effect where CMD13 SEND_STATUS is issued in case mmc_wait_dat0()
does not return -ENOSYS and $send_status is not set. This happens on all
hardware which does implement .mmc_wait_dat0 callback, e.g. i.MX8M .
This leads to lengthy timeout before booting OS in case of eMMC in one
of the HS200/HS400 modes, since the card cannot respond to CMD13 while
downgrading from HS200/HS400 to regular HS mode.
Fix this by adding the missing conditional.
Fixes: 44645f87de ("mmc: Fix mmc_switch excessive timeout")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
