This adds a new board from CS GROUP. The board is called
MCR3000_2G, and has a CPU board called CMPC885.
That CPU board is shared with another equipment that will
be added in a later patch.
That board stores Ethernet MAC addresses in an EEPROM which
is accessed using SPI bus.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
This patch fixes the mpc8xx SPI driver:
- A stub callbacks for mode and speed,
- Use chip selects defined as GPIOs,
- Write proper value to disable relocation, other it fails on mpc885,
- Don't modify ports setup, ports can be different from one board to
another and are already set by board_early_init_r().
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Ports A, C and D are 16 bits ports.
Ports B and E are 32 bits ports.
The "compatible" is used to determine each port type.
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
e1-wan device-tree node doesn't exist. Remove related update
to avoid following warning at startup:
Loading Device Tree to 007fa000, end 007ff951 ... OK
Unable to update property /localbus/e1-wan:data-rate, err=FDT_ERR_NOTFOUND
Unable to update property /localbus/e1-wan:channel-phase, err=FDT_ERR_NOTFOUND
Unable to update property /localbus/e1-wan:rising-edge-sync-pulse, err=FDT_ERR_NOTFOUND
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
Both U-boot and Linux kernel have grown over the last releases
and don't fit anymore in the 2M EPROM of the board.
So, rework the setup to allow storing the Linux kernel image
on the UBIFS NAND Flash.
Also add support to FIT images as this is what the Linux kernel
look like nowadays.
Also increase CFG_SYS_BOOTMAPSZ to 32Mbytes and define
CONFIG_SYS_BOOTM_LEN with the same value, otherwise it defaults
to 8M which is not sufficient anymore with nowadays Linux kernels.
And set the netmask to 255.255.255.0 as a class C address is used.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
We can move all of the environment changes to come
from CONFIG_EXTRA_ENV_TEXT.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmPme8EACgkQxIHbvCwF
GsTJ6RAAiDVG2OFTodxLFVhzxoorrIf/piMZDxtc1ClRxF7CPe5CET18bHp0hvvw
qKJW+dk3aCUSr+E1Ma9ndAHI+/mKmEXudZj/XuUyxlVhm9P8Fw2EQRGZFeogdp0v
/tMB8c7DjW5kTg39/U3z3F7qo6ifs1I8rGcxAhvU38iuOmmIai6AZH1cEq2P2zY9
JdHPzSCVz4TOGzmhJD3wxYMn+DjsLxIT0tggGPRJzXGaAdZdLS7cl/X52rabV/Tq
aJXhjpWNl7RUiNiQbKMtltbmkJQ2MpHkhLGDj2/3H2W5sbpIx0GwDs7r0GSKJ0Ba
6ycn5NBjP3C3gcl91oWJXrzux6LN2aWqe45lgOLpL2H2pPaRlDebBEdDA+oNQKoo
mqX8pMbLfpb3nhg/fOXo/YDZ5Uug42fmpjj3Vu5+imjq9jL+tr5lxZ2oDpsUyT51
MvQXohYTfsYNHQm7M4BzGIuA66WwCJ5TJ3D/YmwdDWPnCCN+QAUMI2/d8Osbct6W
OBGaoZQoRpPZV62+mrHloXW9j8sapcQfJGejdby7S1bxagF/KG/BLXGCWH/HdWCc
TsnW+bOOF4N9gIyyyu3yRfHyE7pIyszWlNwRAuPzjwG0dxEbkboA/JdLIFic3Qsj
fk/65FSvvAeOuvNYEgsEA5VYXJzhD4oNtcNQZHIHjhSTGKBrJF4=
=HVHT
-----END PGP SIGNATURE-----
Merge tag 'efi-2023-04-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2023-04-rc2
Documentation:
* Provide page with links to talks on U-Boot
UEFI:
* Enable CTRL+S to save the boot order in eficonfig command
* Run attribute check for QueryVariableInfo() only for the file store
* Bug fixes
Others:
* Improve output formatting of the coninfo command
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 10 Feb 2023 12:15:45 PM EST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
- DM_SERIAL conversion for bcm7xxx, button input driver, qcom updates,
environment and network related cleanup, ftmac100 update, add a
IS_ENABLED conversion that was just missed.
Register mii_bus with read and write callbacks to allow the 'mii'
command to work. Use a timeout of 10 ms to wait for the R/W
operations to complete.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Replace 'phys_addr_t iobase' with 'struct ftmac100 *ftmac100' in
struct ftmac100_data. It allows to remove casting in a number of places.
Since priv->iobase is phys_addr_t, use phys_to_virt() to make
a pointer from it.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
So it will be named similarly to the related ftgmac100 driver.
The old name 'nds32_mac' is not referred to anywhere in U-Boot.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bootmenu requires an input device with arrows and enter key.
A common smartphone luckily has power, volume up/down buttons,
which may be used for controlling bootmenu.
To use driver, add 'button-kbd' to stdin.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Copied from e83a7e9453 ("powerpc/mpc83xx: Zero boot_flags arg for
calling board_init_f()")
The argument boot_flags of board_init_f() is not used at all in the
powerpc specific board.c init sequence. Now with the generic init
sequence, this boot_flags arg is used by board_init_f().
This patch sets the r3 register that is used to pass the boot_flags
argument from the start.S board_init_f() call to 0 prior to the function
call to avoid unknown content to end up in gd->flags.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: 09f3ca3dd5 ("arm, powerpc: select SYS_GENERIC_BOARD")
Linux event code must be used in input devices, using buttons.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Property count may change in /buttons node, if more button tests added,
and this will break ofnode_for_each_prop.
Add separate node for mentioned test.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
GPIO button driver requires direction functions to probe
button gpio. Those functions are blank, since pwrkey is not
really gpio, and don't support direction settings.
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Add support for Qualcomm I2C QUP driver which is inspired from
corresponding driver in Linux: drivers/i2c/busses/i2c-qup.c.
Currently this driver only support FIFO polling mode which is sufficient
to support devices like eeprom, rtc etc.
Co-developed-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Add clk_rcg_set_rate() which allows to configure clocks without programming
MND values. This is required for configuring I2C clocks on QCS404.
Co-developed-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Mike Worsfold <mworsfold@impinj.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
The Qualcom ETHQOS hardware supports an RGMII macro which needs to be
configured according to following link speeds:
- SPEED_1000
- SPEED_100
- SPEED_10
So add a corresponding glue driver to configure RGMII macro.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The GMAC controller on QCS404 SoC (support added by upcoming patch) fails
to work with maximum tx/rx_fifo_sz supported by the hardware (16K). So
allow platforms to override FIFO size using corresponding DT node
properties.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use standard pinconf drive-strength values from Linux DT bindings rather
than ones based on custom u-boot header. These changes are in direction
to make u-boot DTs for Qcom SoCs to be compatible with standard Linux
DT bindings.
Also, add support for pinconf bias-pull-up.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Currently u-boot maps whole of 1G RAM but there reserved memory ranges on
QCS404 which are reserved for TrustZone, various firmware components etc.
Any access to these reserved memory ranges causes a bus hang issue. So
disable mapping for reserved memory ranges in u-boot.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Boards may set networking variables programmatically, thus may have
CONFIG_NET on but CONFIG_CMD_NET off. The IOT2050 is an example.
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This completes what 890feecaab started by selecting ENV_APPEND and
loading the default env before any other sources. This ensures that load
operations pick up all non-writable vars from the default env and only
permitted parts from other locations according to the regular
priorities.
With this change, boards only need to define the list of writable
variables but no longer have to provide a custom env_get_location
implementation.
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Marek Vasut <marex@denx.de>
CC: Stefan Herbrechtsmeier <stefan.herbrechtsmeier-oss@weidmueller.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_EFI_SECURE_BOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
- This series brings in a large number of patches in the form of changing
CONFIG_IS_ENABLED(FOO) to IS_ENABLED(CONFIG_FOO) when there it is the
case that CONFIG_xPL_FOO is never a valid symbol. The majority of
the times where we do this, it is unintentional and does not make the
code more useful, or rarely, introduces bugs.
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_ATMEL_PIO4 defined in Kconfig
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ROCKCHIP_OTP defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_OF_BOARD defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_FEC_MXC defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT_FLASH_NAND defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This converts 5 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT_FLASH_MMC defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_FASTBOOT defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_EFI_MM_COMM_TEE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_CMD_BOOTEFI_BOOTMGR defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_ARCH_VERSAL defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_DISPLAY_AER_BRIEF defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ZYNQMP_FIRMWARE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_XEN_SERIAL defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>