We configure network phy configuration for internal delay, LED config,
and clock config. If we leave the phy reset gpio defined in dt the
kernel may issue a reset to the phy and break these configs. While some
may be handled by a kernel phy driver, others may not (typically LED
config).
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
binman conversion made flashing flash.bin
and u-boot.itb necessary. Update binman config
to create a single flash.bin image again.
This updates imx8mp_evk and phyCORE-i.MX8MP as they share the
same binman config.
Updated also imx8mp_evk documentation.
Tested on phyCORE-i.MX8MP.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
When purchasing imx8mm-cl-iot-gate it is able to customize the
memory size. It could be 1GB, 2GB and 4GB. We implement
board_phys_sdram_size() to detect the memory size for usage.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Currently imx8mm-cl-iot-gate_defconfig fails to produce a working boot
binary due to the lack of fip.bin:
" BINMAN all
Image 'main-section' is missing external blobs and is non-functional: blob-ext
Some images are invalid"
To make the build process more consistent with the other i.MX8M targets,
split the defconfig in two:
- imx8mm-cl-iot-gate_defconfig: standard defconfig that only
requires ATF / DDR firmware.
- imx8mm-cl-iot-gate-optee_defconfig: "more advanced" defconfig that
requires ATF / Optee / mbedtls / DDR firmware.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Display hwmon values by default when using the 'gsc' command.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add stub for tee_find_device function when CONFIG_TEE is not activated
to simplify the caller code.
This patch allows to remove the CONFIG_IS_ENABLED(OPTEE) tests
for stm32 platform.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@inaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
This adds support for the IOT2050 Basic and Advanced devices. The Basic
used the dual-core AM6528 GP processor, the Advanced one the AM6548 HS
quad-core version.
Both variants are booted via a Siemens-provided FSBL that runs on the R5
cores. Consequently, U-Boot support is targeting the A53 cores. U-Boot
SPL, ATF and TEE have to reside in SPI flash.
Full integration into a bootable image can be found on
https://github.com/siemens/meta-iot2050
Based on original board support by Le Jin, Gao Nian and Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
Generate dfu_alt_info setup at runtime for capsule update.
Enabling this feature will help with upgrading boards without remembering
what is where.
The similar change was done for ZynqMP by commit b86f43de0b ("xilinx:
zynqmp: Add support for runtime dfu_alt_info setup").
Code needs to be enabled by CONFIG_SET_DFU_ALT_INFO.
And also enable capsule on disk for RAW firmware images with efidebug
command.
Two indexes are supported for SPL flow. Images can be generated like:
./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin
./tools/mkeficapsule --raw u-boot.img --index 2 capsule2.bin
Then place them to SD card and load them:
load mmc 0 10000000 capsule1.bin && efidebug capsule update -v 10000000
load mmc 0 10000000 capsule2.bin && efidebug capsule update -v 10000000
FSBL flow will also work where only index 1 capsule is used. There
should be enough space for using boot.bin with bitstream too.
Zynq also support multiple boot locations in SPI or MMC but it is not wired
by this patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/bea5fc75a87a5971f118b46bab4aa7ca39a629c6.1630061610.git.michal.simek@xilinx.com
strncpy() simply bails out when copying a source string whose size
exceeds the destination string size, potentially leaving the destination
string unterminated.
One possible way to address is to pass MDIO_NAME_LEN - 1 and a
previously zero-initialized destination string, but this is more
difficult to maintain.
The chosen alternative is to use strlcpy(), which properly limits the
copy len in the (srclen >= size) case to "size - 1", and which is also
more efficient than the strncpy() byte-by-byte implementation by using
memcpy. The destination string returned by strlcpy() is always NULL
terminated.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After the discussion here:
https://lore.kernel.org/netdev/20210603143453.if7hgifupx5k433b@pali/
which resulted in this patch:
https://patchwork.kernel.org/project/netdevbpf/patch/20210704134325.24842-1-pali@kernel.org/
and many other discussions before it, notably:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/1512016235-15909-1-git-send-email-Bhaskar.Upadhaya@nxp.com/
it became apparent that nobody really knows what "SGMII 2500" is.
Certainly, Freescale/NXP hardware engineers name this protocol
"SGMII 2500" in the reference manuals, but the PCS devices do not
support any "SGMII" specific features when operating at the speed of
2500 Mbps, no in-band autoneg and no speed change via symbol replication
. So that leaves a fixed speed of 2500 Mbps using a coding of 8b/10b
with a SERDES lane frequency of 3.125 GHz. In fact, "SGMII 2500 without
in-band autoneg and at a fixed speed" is indistinguishable from
"2500base-x without in-band autoneg", which is precisely what these NXP
devices support.
So it just appears that "SGMII 2500" is an unclear name with no clear
definition that stuck.
As such, in the Linux kernel, the drivers which use this SERDES protocol
use the 2500base-x phy-mode.
This patch converts U-Boot to use 2500base-x too, or at least, as much
as it can.
Note that I would have really liked to delete PHY_INTERFACE_MODE_SGMII_2500
completely, but the mvpp2 driver seems to even distinguish between SGMII
2500 and 2500base-X. Namely, it enables in-band autoneg for one but not
the other, and forces flow control for one but not the other. This goes
back to the idea that maybe 2500base-X is a fiber protocol and SGMII-2500
is an MII protocol (connects a MAC to a PHY such as Aquantia), but the
two are practically indistinguishable through everything except use case.
NXP devices can support both use cases through an identical configuration,
for example RX flow control can be unconditionally enabled in order to
support rate adaptation performed by an Aquantia PHY. At least I can
find no indication in online documents published by Cisco which would
point towards "SGMII-2500" being an actual standard with an actual
definition, so I cannot say "yes, NXP devices support it".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
After getting MTD device via get_mtd_device_nm(), we need to put it with
put_mtd_device(), otherwise we get
Removing MTD device #0 (mx25l6405d) with use count 1
before booting kernel.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Since Albert Aribaud is not maintaining anymore the LaCie Ethernet Disk
mini V2 board, then I am taking over.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
I am taking over responsibility for the GE board from Sebastian Reichel.
Updating the MAINTAINERS files to reflect this.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The DM DWMAC driver is perfectly capable of configuring the ethernet
PHY reset GPIO, let the driver do it instead of doing it in the board
file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
We have one places that uses this symbol and CONFIG_TARGET_OMAPL138_LCDK
works equally well, switch to that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since cm_t35 was removed, CONFIG_CM_T3X does not exist. This lets us
simplify the code in board/compulab/common/eeprom.c a bit.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
After getting MTD device via get_mtd_device_nm(), we need to put it with
put_mtd_device(), otherwise we get
Removing MTD device #0 (mx25l6405d) with use count 1
before booting kernel.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current API is outdated as it requires a devicetree pointer.
Move these functions to use the ofnode API and update this globally. Add
some tests while we are here.
Correct the call in exynos_dsim_config_parse_dt() which is obviously
wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
Since Albert Aribaud is not maintaining anymore the LaCie Ethernet Disk
mini V2 board, then I am taking over.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
I am taking over responsibility for the GE board from Sebastian Reichel.
Updating the MAINTAINERS files to reflect this.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On MediaTek boards we cannot override the SYS_BOARD / SYS_CONFIG_NAME
variables from defconfig.
This is because in board/mediatek/mtXXXX/Kconfig this value was override
by default due to the if CONFIG_TARGET_MTXXXX condition.
Merge all the Kconfigs to the mach-medatek/Kconfig.
This way:
- we only define SYS_{SOC,VENDOR} once
- all board definitions are in a single place, simplifying the build logic.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFKxpEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBLaB/0XsIdkGAvcHLWW8yUg
27GiRznikNKwn9/qIj2ByraoUd4BvxdQV4gKHR1R9n0sgYh/8VMyLbmhRoCRKFwP
3mQ0MUyjaeU5sEWzasovJVpXhuUapEiV0jEg6t3Lgwd3mp2QK2Pk87zoleQfZNkb
VAVCnt1T+kb3y0W9oa3XZbuH2wam9T5pNWRGW70JbgzdwJNKLO1Qo7MfcUNiDxJu
Jf7uXtYwwILlN38G1KSk1ymMjfaotCqj7RzNaV3Ero57MVj3VzerKGb7H+XPOYf2
nYXyietYLJJkzvHzSDwIdCSVlOSQL8QqVB8GCmLiNQD4tG830RcvSJnYpRLylWQK
6F+Y
=Q/aS
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
The DM DWMAC driver is perfectly capable of configuring the ethernet
PHY reset GPIO, let the driver do it instead of doing it in the board
file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Add new config for storing environment from QSPI1.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: cleanup and add MAINTAINERS entry]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
In order to make it more flexible and allow modifying the base address
of DRAM without recompiling U-Boot, use memory node from device tree
with fdtdec functions.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
In order to make it more flexible and allow modifying the base address
of DRAM without recompiling U-Boot, use memory node from device tree
with fdtdec functions.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
