K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
J721S2 EVM used to store env on eMMC, since EVM and SK uses same
defconfig and there is no eMMC on SK, we need to keep env in an
interface which available on both EVM and SK. So, save env in FAT
partition of MMC SD Card.
Enable defconfigs relevant for storing env on FAT partition of MMC.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Enable configs for building multiple dtbs into a single fit image
and load the right dtb for next stage. Add k3-am68-sk-base-board
dtb along with evm dtb inside DTB FIT image. This helps to use same
defconfig for both EVM and SK
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Change configuration macro name to support all other devices in SEMPER S28
family.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Remove the main_cpsw0_qsgmii_phyinit variable from the boot
command as there is no ethernet firmware in j721s2.
Fixes: 8886341aa6 ('configs: j721s2_evm_a72_defconfig: Add A72 specific defconfig')
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BSS_MAX_SIZE
CONFIG_SPL_MAX_FOOTPRINT
Note that the da850evm platforms were violating the "only use one" rule
here, and so now hard-code their BSS limit.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FS_LOAD_KERNEL_NAME
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a little tricky since SoCFPGA has code to determine this as
runtime. Introduce a guard variable for platforms to select if they
have a static value to use. Then for ARCH_SOCFPGA, call
cm_get_qspi_controller_clk_hz() and otherwise continue the previous
behavior.
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
As the CI test for stopping platforms from being merged that were
defining symbols that had Kconfig entries, a small number of symbols
needed to be migrated again. Do so, and catch two cases the README
should also have been updated but was not.
Signed-off-by: Tom Rini <trini@konsulko.com>
