When env support is disabled then usage of env_get() generates linker
errors. So do not compile env_get() when env support is disabled (for
example when disabled only in SPL).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher then linker throws
error about undefined symbol mmc_mode_name(). So compile mmc_mode_name()
also when CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If env is stored on SD card then U-Boot SPL automatically calls mmc_init()
before it is going to load proper U-Boot from SD card.
If env is not stored on SD card then U-Boot SPL fails to read proper U-Boot
from SD card due to missing mmc_init() call.
So add missing mmc_init() call into fsl_esdhc_spl's mmc_boot() function.
It fixes booting from SD card on P2020 boards without env support in SPL.
mmc_init() returns early if card was already initialized, so there is no
issue with calling this function more times.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In pre-PBL header is stored size of code which BootROM copies from SD card
to L2/SRAM. This size has upper limit of L2 cache size. In most cases this
is size of U-Boot SPL or size of L2 cache.
Therefore this size in pre-PBL header cannot be used for determining size
of proper U-Boot.
So always use CONFIG_SYS_MMC_U_BOOT_SIZE for determining size of proper
U-Boot which stored on SD card.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pre-PBL BootROMs (MPC8536E, MPC8569E, P2020, P1011, P1012, P1013, P1020,
P1021, P1022) require custom BOOT signature on sector 0 and MBR/DBR
signature is not required at all.
So add check for BOOT signature and remove check for MBR/DBR.
This allows U-Boot SPL to load proper U-Boot on pre-PBL BootROMs platforms
also from SD cards which do not have MBR/DBR signature on sector 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
_start symbol contains only 32-bit data number 0x27051956 despite it is
marked as text section. This magic number is IH_MAGIC which is used for
marking uboot image header.
mpc85xx start.S code does not define valid uboot image header, so IH_MAGIC
number in _start symbol is useless there.
Moreover this _start symbol is not used at all. Entry point is at symbol
_start_e500.
So because this _start symbol is not used for anything, completely remove
it with IH_MAGIC number. After _start symbol was _start_cont symbol, so
replace all relative address calculations by _start_cont.
Signed-off-by: Pali Rohár <pali@kernel.org>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
NXP/Freescale Layerscape CPUs support high-speed serial interfaces (SERDES)
that can be configured for the application. Interfaces not used by the
application can be set to protocol 0 to turn them off and save power, but
U-Boot would emit a warning that 0 was invalid for a SERDES protocol on
boot. Replace the warning text with a notice that the SERDES is disabled.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For now, this only provides reset and poweroff functions.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
If we are running in EL2 skip PSCI implementation setup. This avoids an
exception if CONFIG_ARMV8_PSCI is set, but u-boot is started by TF-A.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are two different implementations to do a secure monitor call:
smc_call() and arm_smccc_smc(). The former is defined in fwcall.c and
seems to be an ad-hoc implementation. The latter is imported from linux.
smc_call() is also only available if CONFIG_ARMV8_PSCI is not defined.
This makes it impossible to have both PSCI calls and PSCI implementation
in one u-boot build. The layerscape SoC code decide at runtime via
check_psci() if there is a PSCI support. Therefore, this is a
prerequisite patch to add PSCI implementation support for the layerscape
SoCs.
Note, for the TFA part, this is only compile time tested with
(ls1028ardb_tfa_defconfig).
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
psci_update_dt() is also required if CONFIG_ARMV8_PSCI is set, that is,
if u-boot is the PSCI provider.
Guard the check which is intended to call into the PSCI implementation
in the secure firmware, by the proper macro SEC_FIRMWARE_ARMV8_PSCI.
Mark the function as weak because - unfortunately - there is already
a stub of the same function in arch/arm/mach-rmobile/psci-r8a779a0.c
which does not the same as the common one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a Kconfig for this erratum, but it is ignored for armv8.
Respect it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
On Layerscape platforms, the DTB is loaded from boot filesystem,
per the fdt_addr description in doc/README.distro, it must be
removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Add "-q" to fdt addr and use it in distro_bootcmd to make the user
experience less scary reading in normal try/fail cases.
- Let the adc update an environment variable like many other commands do
- Fix TPL SEPARATE_BSS check when locating DTB
- Allow ":" in PXE file names again
- Two Apple M1 fixes
Unless you have a spare Apple Silicon machine, getting access to
the serial port on Apple Silicon machines requires special
hardware. Given that most machines come with a built-in screen
the framebuffer is likely to be the most convenient output device
for most users. While U-Boot will output to both serial and
framebuffer, OSes might not. Therefore set stdout-path to point
at /chosen/framebuffer when a keyboard is connected to the machine.
This behaviour can be overridden by setting the "stdout" variable
in the U-Boot environment. I addition to that keep the serial
console as the default when running under the m1n1 hypervisor.
The m1n1 hypervisor virtualizes the serial port such that it
can be easily accessed from any other machine with a USB port.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Janne Grunau <j@jannau.net>
Tested-by: Janne Grunau <j@jannau.net>
Enable CONFIG_NO_FB_CLEAR to preserve the Asahi logo. Since that
logo is drawn on a black background also enable
CONFIG_SYS_WHITE_ON_BLACK such that text printed by U-Boot is still
visible.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
- U-boot's PXE flow supports prefixing your bootfile name with an
IP address to fetch from a server other than the DHCP server,
e.g. `hostIPaddr:bootfilename`:
a93907c43f
- However, this breaks bootfile paths which contain a colon, e.g.
`f0:ad:4e:10:1b:87/7/pxelinux.cfg/default`
- This patch checks whether the `hostIPaddr` prefix is a valid
IP address before overriding the serverIP otherwise the whole
bootfile path is preserved
Signed-off-by: Lyle Franklin <lylejfranklin@gmail.com>
distro_bootcmd uses this construct a few times to test $fdt_addr_r,
and fall back on $fdtcontroladdr if not set/invalid:
if fdt addr ${fdt_addr_r}; then
...
else
...
fi
If the `fdt addr` test fails, it prints the following message on the
console, suggesting there is an error when there is not:
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
To remove this potentially confusing error message, this patch adds -q
as a 'quiet' option for fdt addr, and uses this flag in
config_distro_bootcmd.h
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Add the ability to save ADC conversion result in an environment
variable. This is useful for further arbitrary processing by the
U-Boot scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Commit 690af71850 changed this condition
from an explicit
IS_ENABLED(CONFIG_SPL_SEPARATE_BSS)
to
CONFIG_IS_ENABLED(SEPARATE_BSS)
The documentation for CONFIG_IS_ENABLED() in include/linux/kconfig.h
implies that we will get the correct behaviour, but the actual behaviour
differs such that this condition is now always false.
This stopped TPL being able to load the device tree blob at least on the
ROCKPro64 board (RK3399 SoC), since the wrong device tree location was
chosen.
The issues causing this behaviour with CONFIG_IS_ENABLED() are:
1. The documentation implies that CONFIG_SPL_BUILD =>
CONFIG_SPL_<option> is considered before the TPL equivalent.
Actually, the TPL options have higher priority - see definition of
_CONFIG_PREFIX.
2. The documentation implies a fallthrough, eg. if CONFIG_SPL_BUILD is
defined but the CONFIG_SPL_<option> is not, then it will proceed to
check if CONFIG_TPL_BUILD
Actually, if CONFIG_TPL_BUILD is defined, then it stops there
and CONFIG_SPL_BUILD is not considered - see definition of
_CONFIG_PREFIX.
During TPL build, at least for the ROCKPro64, both CONFIG_TPL_BUILD
and CONFIG_SPL_BUILD are defined, but because of the above, only TPL
options are considered. Since there is no CONFIG_TPL_SEPARATE_BSS,
this fails.
Fixes: 690af71850 ("fdt: Correct condition for SEPARATE_BSS")
Signed-off-by: Andrew Abbott <andrew@mirx.dev>
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes: 3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Allow to disable PHY driver in SPL because it checks the CONFIG_SPL_PHY
variable for SPL builds.
The same change was done for usb by commit fd09c205fc ("usb:
s/CONFIG_DM_USB/CONFIG_IS_ENABLED(DM_USB)/").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add watchdog controller driver for NPCM7xx/npcm8xx
the wdt design of npcm750 and npcm845 is the same.
so the driver can work on npcm750 and npcm845.
about npcm845 wdt dtsi i will followed kernel dts name
to use nuvoton,npcm750-wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds simple documentation about common properties for watchdog
in the device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Fix SPL_SYS_MALLOC_SIMPLE and non-SPL_FRAMEWORK boards (a large number
of PowerPC platforms)
- Remove duplication of crc16 functionality
- Migrate COUNTER_FREQUENCY to CONFIG_COUNTER_FREQUENCY and have it in
Kconfig
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 35bb60787b. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in
config header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: Re-run migration]
Set default COUNTER_FREQUENCY according to config header file
under include/configs/
i.MX6UL/ULL/7D/8QM/8QXP all has system counter frequency run at 8MHz,
so set default value for them.
SUNXI/EXYNOS/ROCKCHIP_RK3128/ROCKCHIP_RK3288/ROCKCHIP_RK322X/ROCKCHIP_RK3036
at 24MHz. ARCH_LX2160A at 25MHz
ARCH_ZYNQMP at 100MHz
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ATSHA204A uses bit-reversed checksum of standard CRC-16 with polynomial
x^16 + x^15 + x^2 + 1.
This ATSHA204A specific checksum can be calculated just by using common
U-Boot functions bitrev16() and crc16().
So replace custom driver CRC-16 implementation by common U-Boot functions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Implementation in linux/crc16.h provides standard CRC-16 algorithm with
polynomial x^16 + x^15 + x^2 + 1. Use it and remove duplicate ext4 CRC-16
specific code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
