Commit graph

236 commits

Author SHA1 Message Date
Valentin Longchamp
89127c5346 km/powerpc: fix ft_board_setup prototype for km82xx & km83xx
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:58 -05:00
Valentin Longchamp
5411988242 powerpc/83xx: add support for kmtegr1 board
This board uses the same CPU (8309) as VECT1. The memory however is
different since it has NAND Flash, the NOR Flash partitioning is
different and of course the FPGAs as well.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
2015-11-18 15:28:58 -05:00
Bagavathiannan Palanisamy
cd7255fdc2 board/keymile/km82xx: setting dip_switch 3 and 4 will run bootloader
Setting dip_switch 3 and 4 also will run bootloader in COGE3 and COGE6
It is required remove local mgmt IP address, when DIP Switch PIN3 is
enabled. DIP Switch 4 also enabled to avoid u-boot update in future
for DIP switch enhancements.

Signed-off-by: Bagavathiannan Palanisamy <Bagavathiannan.Palanisamy@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:56 -05:00
Holger Brunck
8b2dd8a9b5 km/powerpc82xx: remove unused function
commit 0a4f88b98 removed the usage of our setports function, but the
function itself were not removed. So toss it it's dead code.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:55 -05:00
Holger Brunck
fc882a310d km/powerpc: remove unneeded defines
We use CONFIG_OF_LIBFDT and CONFIG_OF_BOARD_SETUP on all our powerpc
targets, so there is no need to check these defines within our C code.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:54 -05:00
Holger Brunck
d3f1d6f434 powerpc/82xx/km: add testpin detection for mgcoge3ne
On mgcoge3ne we also want to start the test application if the testpin
is asserted. But we don't have a full POST test support yet. So simply
add a function to read the testpin value.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:53 -05:00
Holger Brunck
74edc607d6 powerpc/82xx: make set/get_pin for km82xx more flexible
The get_pin and set_pin funciton was only used for pins on Port D and
therefore the value was hard coded in the function. Enhance this with a
parameter, that we are able to use this functions for other ports too.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:52 -05:00
Christoph Dietrich
c1e121e4bd powerpc/83xx: add support for kmtepr2 board
This board is similar to TUXX1, but it has differend FPGAs.

Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:51 -05:00
Tobias Müller
ef3f2f08f7 km/scripts: search for kernel/DTBs at serverip:/PRODUCTNAME via TFTP in develop mode
Search for the kernel and DTBs in a folder named PRODUCTNAME (found in the IVM)
at the TFTP server instead of the u-boot boardname.

Signed-off-by: Tobias Müller <Tobias.Mueller@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-18 15:28:51 -05:00
Holger Brunck
91b9db0be5 km/scripts: load fdt_bid_kwkey.dtb when working with tftp
When loading the dtb file via tftp we should load the one which matches
boardId and hwKey and not a common one for the boardname. We have boards
were different hwKeys are used and then we may load an incorrect dtb
file. If no fdt_bid_kwkey.dtb file is not a fallback to boardname.dtb is used.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Tobias Müller <Tobias.Mueller@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2015-11-18 15:28:50 -05:00
Valentin Longchamp
30f9ad77c4 arm/km_kirkwood: fix the #ifdef for KM_COGE5UN dip switch
There was a small typo for KM_COGE5UN that resulted in the dip switch
not to behave as expected.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:49 -05:00
Holger Brunck
e23fde7d1f arm/mgcoge3un: check dip_switch at startup
Similar to kmcoge5un we need to check the dip switch at startup
connected to the kirkwood at MPP43. If it's set we need to set the
actual_bank to zero to boot from SW bank zero. Additional to kmcoge5un
we need to check also the pin in misc_init to decide wether we wait for
the ne to start or not. If the dip_switch is set we don't wait and
continue immediately.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-11-18 15:28:48 -05:00
Tobias Müller
9ff739e422 arm/km: Fix LED configuration for 88E1118R PHY (PIGGY3)
Configure PHY LED register for Marvell 88E1118R PHY used on PIGGY3 to
match with printed descriptions on PCB

Signed-off-by: Tobias Müller <Tobias.Mueller@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[trini: Fix typo, CRTL_PAGE -> CTRL_PAGE]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-18 15:28:30 -05:00
Valentin Longchamp
60c4ae00be KM/IVM: remove ivm_read_eeprom(void)
This is not used anymore since the procedure was split into a simple
read function and a later alaysis.

The ivm_read_eeprom name is now used for the previous
ivm_simple_read_eeprom function.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-02-16 15:48:36 -05:00
Valentin Longchamp
2973b098ba 82xx/km82xx: read the IVM eeprom earlier
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.

Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-02-16 15:48:35 -05:00
Valentin Longchamp
f32b3d3fce 83xx/km83xx: read the IVM eeprom earlier
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.

Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-02-16 15:48:35 -05:00
Valentin Longchamp
0fdb6eadff 85xx/kmp204x: read the IVM eeprom earlier
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.

Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-02-16 15:48:35 -05:00
Valentin Longchamp
0bb95a68fc kirkwood/km_arm: read the IVM eeprom earlier
This allows to define the ethaddr env variable according to the the IVM
content by reading the IVM in misc_init_r.

Later, when HUSH is available the content read earlier is analyzed to
populate some non env variables.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-02-16 15:48:35 -05:00
Valentin Longchamp
16ac90c7ee KM/IVM: split the IVM reading and parsing in 2 parts
This allows to first read the IVM content (earlier in the boot sequence)
and define the ethaddr env variable thanks to the ivm_read_eepromi().
Later, the IVM content can be parsed and used to define some hush
variables, when the hush subsystem is available thanks to
ivm_analyze_eeprom().

To avoid the HW read to happen twice, the buffer passed to
ivm_read_eeprom() has to be reused by ivm_analyze_eeprom (and thus
allocated before calling ivm_read_eeprom()).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2015-02-16 15:48:34 -05:00
Holger Brunck
ab23b9a024 km/km82xx: remove CONFIG_SYS_RAMBOOT
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:10 -08:00
Simon Glass
e895a4b06f fdt: Allow ft_board_setup() to report failure
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.

Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.

Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
2014-11-21 04:43:15 +01:00
Wolfgang Denk
0060517ae0 cppcheck cleanup: fix nullPointer errors
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.

Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-11-07 16:27:07 -05:00
Stefan Roese
96c5f0816a arm: kirkwood: Change naming of dram functions from km_foo() to mvebu_foo()
Additionally the SDRAM address decoding register address is not hard coded
in the C code any more. A define is introduced for this base address.

This makes is possible to use those gpio functions from other MVEBU SoC's
as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:21 -04:00
Stefan Roese
d5c5132f87 arm: marvell: Extract kirkwood gpio functions into new common file gpio.c
This makes is possible to use those gpio functions from other MVEBU SoC's as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:21 -04:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Masahiro Yamada
47539e2317 kirkwood: kconfig: refactor Kconfig and defconfig
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
2014-08-30 21:21:21 -04:00
Valentin Longchamp
f38391793f kmp204x: reset the Zarlink clocking chips at power up only
There is the requirement on the chassis's backplane that when the clocks
have been enabled, they then should not disappear.

Resetting the Zarlink clocking chips at unit reset violates this
requirement because the backplane clocks are not supplied during the
reset time.

To avoid this side effect, both the Zarlink clocking chips are reset
only at power up.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-08-20 10:44:42 -07:00
Tom Rini
dcdb61a084 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2014-08-06 08:38:18 -04:00
Boschung, Rainer
e3917b21c0 kmp204x: prepare to use CPU watchdog
This patch configures the qrio to trigger a core reset on
a CPU reset request.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:59 -07:00
Boschung, Rainer
6caa185abd kmp204x/qrio: support for setting the CPU reset request mode
To acheive this, the qrio_uprstreq() function that sets the UPRSTREQN
flag in the qrio RESCNF reg is added.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:53 -07:00
Boschung, Rainer
a09f470d49 kmp204x: set CPU watchdog reset reason flag
Check the core timer status register (TSR) for watchdog reset,
and and set the QRIO's reset reason flag REASON1[0] accordingly.

This allows the appliction SW to identify the cpu watchdog as a
reset reason, by setting the REASON1[0] flag in the QRIO.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:46 -07:00
Boschung, Rainer
807d93d6de kmp204x/qrio: prepare support for the CPU watchdog reset reason
To achieve this, the qrio_cpuwd_flag() function that sets the CPU watchdog
flag in the REASON1 reg is added.

Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-08-01 14:18:40 -07:00
Masahiro Yamada
93d4334f7f Add board MAINTAINERS files
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:06 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Jeroen Hofstee
2716077cda board:keymile: remove unnecessary double braces
Clang interpretes an if condition like  "if ((a = b) == NULL)
as it tries to assign a value in a statement. Hence if you do
"if ((something)) it warns you that you might be confused.
Hence drop the double braces for plane if statements.

cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-06-11 16:27:06 -04:00
Simon Glass
eca86fad3d Rename hush to cli_hush
Hush is a command-line interpreter, so rename it to make that clearer.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-05-29 17:45:31 -04:00
Valentin Longchamp
2846c43e2d kmp204x: add workaround for A-004849
This should prevent the problems that the CCF can deadlock with certain
traffic patterns.

This also fixes the workaround for A-006559 that was not correctly
implemented before.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Valentin Longchamp
e20c822d0e kmp204x: update the RCW
Fix the IRQ/GPIO settings: all the muxed GPIO/external IRQs that are
used as internal interrupts are defined as GPIOs to avoid confusion
between the internal/external interrupts.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Valentin Longchamp
af47faf650 kmp204x: complete the reset sequence and PRST configuration
This adds the reset support for the following devices that was until
then not implemented:
- BFTIC4
- QSFPs

This also fixes the configuration of the prst behaviour for the other
resets: Only the u-boot and kernel relevant subsystems are taken out of
reset (pcie, ZL30158, and front eth phy).

Most of the prst config move to misc_init_f(), except for the PCIe
related ones that are in pci_init_board and the bftic and ZL30158 ones
that should be done as soon as possible.

Only the behavior of the Hooper reset is changed according to the
documentation as the application is not able to not configure the switch
when it is not reset.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Valentin Longchamp
18794944c6 kmp204x: selftest/factory test pin support
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
  a script by setting the active bank to testbank

The post_hotkeys_pressed return the state of the SELFTEST pin.

The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.

Finally, the unused #defines for the not so relevant mtest command are
removed.

Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:55 -07:00
Stefan Bigler
4921a149e1 kmp204x: handle dip-switch for factory settings
Add readout of dip-switch to revert to factory settings.
If one or more dip-switch are set, launch bank 0 that contains the
bootloader to do the required action.

Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:54 -07:00
Stefan Bigler
a53e65d053 kmp204x: Add support for the unit LEDs
The unit LEDs are managed by the QRIO CPLD. This patch adds support for
accessing these LEDs in the QRIO.

The LEDs then are set to a correct boot state:
- UNIT-LED is red
- BOOT-LED is on.

Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-05-13 08:26:54 -07:00
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Gerlando Falauto
9c134e189a arm/km: introduce kmsugp1 target
KMSUGP1 is from a u-boot perspective (almost) identical to KMNUSA.
The only difference is that the PCIe reset is connected to Kirkwood pin
MPP7_PEX_RST_OUTn, we use a dedicated config flag KM_PCIE_RESET_MPP7.
Such pin should theoretically be handled by the PCIe subsystem
automatically, but this turned out not to be the case.
So simply configure this PIN as a GPIO and issue a pulse manually.

Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Karlheinz Jerg <karlheinz.jerg@keymile.com>
Cc: Valentin Longchamp <valenting.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 17:45:36 +01:00
Gerlando Falauto
b1c2a7ae32 arm/km: define fdt_high env variable and allow backwards compatibility
Add set_fdthigh subcommand to "subbootcmds" (release) so to set "fdt_high"
This is necessary on Kirkwood so that the FDT does not get relocated
above the memory limit that the kernel cannot access
(that is the memory part reserved for the switch).
This was tested on NUSA1, where it is necessary, and on ETER1, where it
doesn't seem to hurt.

We want the scripts to also work with older versions of u-boot, where:
a) set_fdthigh is not defined (will be default env for newer u-boots)
b) the fdt will not be available

For this reason, we use "set_fdthigh" to tell whether we are running
a newer (FDT-aware) u-boot or not.
So if "set_fdthigh" runs successfully or arch != arm we try loading
the fdt; otherwise we proceed normally.

Notice how, contrary to release mode, set_fdthigh will _not_ be part of
subbootcmds for develop and ramfs, but will be executed as part of
"tftpfdt".

Since this is only needed for kirkwood cards, and it prevents the kernel
from booting on QorIQ (though it seemed to work on ETER1), we change
its definition in the default env for powerpc so that the value is only
set on ARM.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:18:13 +01:00
Gerlando Falauto
7b2268b88f arm/km: enable FDT for km_kirwkood
This consists of:
a) Defining the addresses, enabling fdtsupport [arm]
b) Defining "cramfsloadfdt"  [arm,powerpc => common]
c) Adding the FDT address to bootm [arm,powerpc => common]
d) Defining "tftpfdt" in ramfs-,develop- [arm,powerpc >= common]

This should work with 3.10 kernels, whether loaded through TFTP
(with rootfs either through NFS or TFTP-ramfs) or from the NAND.

The machid was left unchanged, this should keep compatibility with both
older and newer kernels.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:17:54 +01:00
Holger Brunck
fa6e0ecb8a arm/km: fix wrong error handling
miiphy_read and miiphy_write are returning 0 on success.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:17:39 +01:00
Holger Brunck
aef0bdc0c0 arm/km: make local function startup_allowed static
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:16:35 +01:00
Holger Brunck
bbfd509da6 arm/km: drop unneeded define
CONFIG_BOOTCOUNT_LIMIT is used on all boards from this board series. So
remove this unneeded define.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2014-02-13 16:15:32 +01:00