Commit graph

13 commits

Author SHA1 Message Date
Lokesh Vutla
e938b22521 arm: K3: Clean and invalidate Linux Image before jumping to Linux
U-Boot cleans and invalidate L1 and L2 caches before jumping to Linux
by set/way in cleanup_before_linux(). Additionally there is a custom
hook provided to clean and invalidate L3 cache.

Unfortunately on K3 devices(having a coherent architecture), there is no
easy way to quickly clean all the cache lines for L3. The entire address
range needs to be cleaned and invalidated by Virtual Address. This can
be implemented using the L3 custom hook but it take lot of time to clean
the entire address range. In the interest of boot time this might not be
a viable solution.

The best hit is to make sure the loaded Linux image is flushed so that
the entire image is written to DDR from L3. When Linux starts running with
caches disabled the full image is available from DDR.

Reported-by: Andrew F. Davis <afd@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25 17:33:21 -04:00
Lokesh Vutla
e69ffdb763 arm: k3: Use driver_name to get ti_sci handle
Use the driver name to get ti_sci handle rather than relying
on just the FIRMWARE uclass.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:32:20 -04:00
Lokesh Vutla
f8ca912189 arm: k3: Add support for printing CPUINFO
Add support for printing CPU info for all K3 devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-11 13:31:18 -04:00
Andreas Dannenberg
e630afe1de arm: K3: common: Allow for early console functionality
Implement an early console functionality in SPL that can be used before
the main console is being brought up. This helps in situations where the
main console is dependent on System Firmware (SYSFW) being up and running,
which is usually not the case during the very early stages of boot. Using
this early console functionality will allow for an alternate serial port
to be used to support things like UART-based boot and early diagnostic
messages until the main console is ready to get activated.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-11 10:07:33 -04:00
Andrew F. Davis
29c9db4d98 board: ti: am654: Disable TRNG node for HS devices
On HS devices the access to TRNG is restricted on the non-secure
ARM side, disable the node in DT to prevent firewall violations.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-04 12:21:23 -04:00
Lokesh Vutla
e8d3a18639 arm: k3: Fix getting ti_sci handle
API get_ti_sci_handle() is relying on the device-tree node name
to be "dmsc" for probing the ti_sci device. But with the introduction
of debug messages for dmsc, the node name changed to dmsc@44083000.
Because of this ti_sci is never probed cause a boot failure. Instead
of relying on device-tree node name, use the first available firmware
node for probing ti_sci.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-09-13 11:56:30 -04:00
Lokesh Vutla
c2562d7c9e arm: K3: j721e: Add basic support for J721E SoC definition
The J721E SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration to enable lower system costs
of automotive applications such as infotainment, cluster, premium
Audio, Gateway, industrial and a range of broad market applications.
This SoC is designed around reducing the system cost by eliminating
the need of an external system MCU and is targeted towards ASIL-B/C
certification/requirements in addition to allowing complex software
and system use-cases.

Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep
  capable dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA),
  C7x floating point Vector DSP, Two C66x floating point DSPs.
* 3D GPU PowerVR Rogue 8XE GE8430
* Vision Processing Accelerator (VPAC) with image signal processor and Depth
  and Motion Processing Accelerator (DMPAC)
* Two Gigabit Industrial Communication Subsystems (ICSSG), each with dual
  PRUs and dual RTUs
* Two CSI2.0 4L RX plus one CSI2.0 4L TX, one eDP/DP, One DSI Tx, and
  up to two DPI interfaces.
* Integrated Ethernet switch supporting up to a total of 8 external ports in
  addition to legacy Ethernet switch of up to 2 ports.
* System MMU (SMMU) Version 3.0 and advanced virtualisation
  capabilities.
* Upto 4 PCIe-GEN3 controllers, 2 USB3.0 Dual-role device subsystems,
  16 MCANs, 12 McASP, eMMC and SD, UFS, OSPI/HyperBus memory controller, QSPI,
  I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Two hardware accelerator block containing AES/DES/SHA/MD5 called SA2UL
  management.
* Configurable L3 Cache and IO-coherent architecture with high data throughput
  capable distributed DMA architecture under NAVSS
* Centralized System Controller for Security, Power, and Resource
  Management (DMSC)

See J721E Technical Reference Manual (SPRUIL1, May 2019)
for further details: http://www.ti.com/lit/pdf/spruil1

Add base support for J721E SoC

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2019-07-26 21:49:25 -04:00
Lokesh Vutla
c0669d28ee armv7R: k3: Release all the exclusive devices
Release all the exclusive devices held by SPL.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-26 21:49:22 -04:00
Andreas Dannenberg
f9380a730d armv7R: K3: am654: Shut down R5 core after ATF startup on A53
Rather than simply parking the R5 core in WFE after starting up ATF
on A53 instead use SYSFW API to properly shut down the R5 CPU cores
as well as associated timer resources that were pre-allocated. This
allows software further downstream to properly and gracefully bring
the R5 cores back online if desired.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-26 21:49:22 -04:00
Lokesh Vutla
a9a84480f4 arm: k3: Add support for updating msmc dt node
Certain parts of msmc sram can be used by DMSC or can be
marked as L3 cache. Since the available size can vary, changing
DT every time the size varies might be painful. So, query this
information using TISCI cmd and fixup the DT for kernel.
Fixing up DT does the following:
- Create a sram node if not available
- update the reg property with available size
- update ranges property
- loop through available sub nodes and delete it if:
	- mentioned size is out if available range
	- subnode represents l3 cache or dmsc usage.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12 08:05:51 -04:00
Lokesh Vutla
6ce424a920 arm: k3: Add a wrapper to get tisci handle
Create a wrapper to get the ti sci handle.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-04-12 08:05:51 -04:00
Andreas Dannenberg
4a1fa524e9 arm: mach-k3: common: Clean up ATF image startup function
Perform some cosmetic cleanup of the ATF image startup function, namely
fixing a spelling mistake, capitalization of a few words, spacing, as
well aligning how errors are printed and as using panic() for cases that
were using a combination of printf() + hang().

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-02-09 07:51:02 -05:00
Lokesh Vutla
a3501a4a44 armv7R: K3: am654: Add support to start ATF from R5 SPL
Considering the boot time requirements, Cortex-A core
should be able to start immediately after SPL on R5.
Add support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2018-11-16 16:51:58 -05:00