T4160QDS shares the same platform as T4240QDS. T4160 is a low power
version of T4240, with eight e6500 cores, two DDR3 controllers, and
slightly different SerDes protocols.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Separate CONFIG_PPC_T4240 from board config file. Prepare to add more SoC
variants supported on the same board.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Protocols are constants. Fix arrays with const prefix.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The PIR parsing algorithm we used is not only for E6500. It applies to all
SoCs with chassis 2.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use decimal and hexadecimal for protocol numbers. It helps to match with
SoC user manual.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 internal UTMI phy is different comparing to previous UTMI PHY
in P3041.
This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for
T4240.
The phy timing is very sensitive and moving the phy enable code to
cpu_init.c will not work.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 has voltage ID fuse. Read the fuse and configure the voltage
correctly. Core voltage has higher tolerance on over side than below.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Missing nodes of crypto, pme, etc in device tree is not a fatal error.
Setting up the qman portal should skip the missing node and continue
to finish the rest.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Should check if interleaving is enabled before using interleaving mode.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Update the timing table to support more rank density, based on the theory
that similar density DIMMs have similar clock adjust and write level start
timing. Update the timing for 1600 and 1866 MT/s. Tested with Micron
MT18JSF1G72AZ-1G9E1 DIMMs, iDIMM M3CN-4GMJ3C0C-M92.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Lane H on SerDes4 should be SATA2 instead of SATA1
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. fix 10G mac offset by plus 8;
2. add second 10G port info for FM1 & FM2 when init ethernet info;
3. fix 10G lanes name to match lane protocol table;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reverse the bit sequence to set and display serdes clock frequency
correctly. The correct bit maps in BRDCFG2 are
0 1 2 3 4 5 6 7
S1RATE[1:0] S2RATE[1:0] S3RATE[1:0] S4RATE[1:0]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The L1 D-cache on e6500 is write-through. This means that it's not
considered a good idea to have the L1 up and running if the L2 is
disabled. We don't actually *use* the L1 until after the L2 is
brought up on e6500, so go ahead and move the L1 enablement after
that code is done.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Fix ccsr_gur for corenet platform. Remove non-exist registers. Add fuse
status register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Makes it a bit easier to see if we've properly set them. While
we're in there, modify the accesses to HDBCR0 and HDBCR1 to actually
use those definitions.
Signed-off-by: Andy Fleming <afleming@freescale.com>
The bit positions for FMAN1 freq in RCW is different for B4860.
Also addded a case when FMAN1 frewuency is equal to systembus.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added the LAN9730 to list of supported devices. This chip is used
in the sEVM, uEVM and som5_evb. Tested on the som5_evb with dhcp
and ping.
Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
Sparc only really sets up the ramdisk, but we should still use
image_setup_linux() so that setup is common across all architectures
that use the FDT.
Cover-letter
Introduce a common image_setup_linux() function
This series continues the work to tidy up the image code. Each
architecture has its own code for setting up ready for booting linux.
An attempt is made here to unify these in a single image_setup_linux()
function.
The part of the image code that deals with FDT is split into image-fdt.c
and a few tweaks are added to make FIT images more viable in SPL.
END
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having similar code in m68k, use image_setup_linux() which
should be common across all architectures that use the FDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than having similar code in powerpc, use image_setup_linux() which
should be common across all architectures that use the FDT.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the common FDT setup function that is now available in image. Move
the FDT-specific code to a new bootm-fdt.c and remove unused headers
from bootm.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
With fewer #ifdefs the code is more readable and more of the code is
compiled for all boards. Add defines in the header file to control
what features are enabled, and then use if() instead of #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems to be a common function for several architectures, so create
a common function rather than duplicating the code in each arch.
Also make an attempt to avoid introducing #ifdefs in the new code, partly
by removing useless #ifdefs around function declarations in the image.h
header.
Signed-off-by: Simon Glass <sjg@chromium.org>
The image file is still very large, and some of the code is only used when
libfdt is in use. Move this code into a new file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is very large, and in SPL it isn't always useful to print
out image information (in fact there might not even be a console
active). So disable this feature unless this option is set.
Signed-off-by: Simon Glass <sjg@chromium.org>
The fit_handle_file() function is quite long - split out the part that
loads and checks a FIT into its own function. We will use this
function for storing public keys into a destination FDT file.
The error handling is currently a bit repetitive - tidy it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Much of the image code uses addresses as ulongs and pointers interchangeably,
casting between the two forms as needed.
This doesn't work with sandbox, which has a U-Boot RAM buffer which is
separate from the host machine's memory.
Adjust the cost so that translating from a U-Boot address to a pointer uses
map_sysmem(). This allows bootm to work correctly on sandbox.
Note that there are no exhaustive tests for this code on sandbox, so it is
possible that some dark corners remain.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de> (v1)
This function will be used to print signatures as well as hashes, so rename
it. Also make it static since it is not used outside this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We intend to add signatures to FITs also, so rename this function so that
it is not specific to hashing. Also rename fit_image_set_hashes() and
make it static since it is not used outside this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The string " error\n" appears in each error string. Move it out to a
common place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The existing function is long and most of the code is indented a long
way. Before adding yet more code, split this out into its own function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de> (v1)
This is the main entry point to the FIT image verification code. We will
be using it to handle image verification with signatures, so rename the
function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function doesn't need to be exported, and with verification
we want to use it for setting the 'value' property in any node,
so rename it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function has become quite long and much of the body is indented quite
a bit. Move it into a separate function to make it easier to work with.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
This code is never compiled into U-Boot, so move it into a separate
file in tools/ to avoid the large #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The FIT code is about half the size of the >3000-line image.c. Split this
code into its own file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
One we split out the FIT code from image.c we will need this function.
Export it in the header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Rather than repeat the line
#if defined(CONFIG_TIMESTAMP) || defined(CONFIG_CMD_DATE) || \
defined(USE_HOSTCC)
everywhere, put this in a header file and #define IMAGE_ENABLE_TIMESTAMP
to either 1 or 0. Then we can use a plain if() in most code and avoid
the #ifdefs.
The compiler's dead code elimination ensures that the result is the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Iterating through subnodes with libfdt is a little painful to write as we
need something like this:
for (depth = 0, count = 0,
offset = fdt_next_node(fdt, parent_offset, &depth);
(offset >= 0) && (depth > 0);
offset = fdt_next_node(fdt, offset, &depth)) {
if (depth == 1) {
/* code body */
}
}
Using fdt_next_subnode() we can instead write this, which is shorter and
easier to get right:
for (offset = fdt_first_subnode(fdt, parent_offset);
offset >= 0;
offset = fdt_next_subnode(fdt, offset)) {
/* code body */
}
Also, it doesn't require two levels of indentation for the loop body.
Signed-off-by: Simon Glass <sjg@chromium.org>
(Cherry-picked from dtc commit 4e76ec79)
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Move this definition from aisimage.c to mkimage.h so that it is available
more widely.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
We don't measure boot timing on the host, or with SPL, so use both
conditions in the bootstage header. This allows us to avoid using
conditional compilation around bootstage_...() calls. (#ifdef)
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than needing to call one of many hashing algorithms in U-Boot,
provide a function hash_block() which handles this, and can support all
available hash algorithms.
Once we have md5 supported within hashing, we can use this function in
the FIT image code.
Signed-off-by: Simon Glass <sjg@chromium.org>
