Commit graph

13287 commits

Author SHA1 Message Date
Aneesh V
d2f18c275e omap4: utility function to identify the context of hw init
The basic hardware init of OMAP4(s_init()) can happen in 4
different contexts:
 1. SPL running from SRAM
 2. U-Boot running from FLASH
 3. Non-XIP U-Boot loaded to SDRAM by SPL
 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
    Configuration Header feature

What level of hw initialization gets done depends on this
context. Add a utility function to find this context.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Laurence Withers
732590b397 DA8xx: fix LPSC constants
Some of the LPSC constants were incorrect, and some were missing. This
commit fixes the incorrect constants (which were not used anywhere in
the tree) and adds all constants for both DA830 and DA850, as per the
TI datasheets.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Laurence Withers
37dbd1c1ad DA8xx: switch an enum to defines for consistency
There are two main sets of LPSC constants, depending on the processor
family.  The DA8xx constants were given in an enum whereas the non-DA8xx
constants were preprocessor defines. This commit switches the DA8xx
constants to defines for consistency.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Laurence Withers
2c6e0b07dc DA8xx: add MMC/SD controller addresses
Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Laurence Withers
da51e424d2 DaVinci EMAC: declare function for all DA8xx CPUs
The function davinci_emac_mii_mode_sel() is defined in
board/davinci/common/misc.c for any DA8xx CPU which has
CONFIG_DRIVER_TI_EMAC enabled. However, the prototype was only being
declared in <include/asm/arch/davinci_misc.h> for the DA850 EVM board.
This patch declares it for all DA8xx CPUs where CONFIG_DRIVER_TI_EMAC
is enabled.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Laurence Withers
f517afd5df DA8xx: add generic GPIO driver
Add a generic GPIO driver for the DaVinci DA8xx processors. It is turned
on by defining CONFIG_DA8XX_GPIO and fulfills the generic GPIO interface
specified in <asm/gpio.h> . The driver has support for both manipulating
GPIO pins as well as automatically configuring the pin multiplexor
registers to set the pin function to GPIO.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Laurence Withers
0bf98f1d13 DaVinci: rename gpio_defs.h to gpio.h
In preparation for a generic GPIO driver for the DA8xx processors,
rename <asm/arch/gpio_defs.h> to <asm/arch/gpio.h> and fix up all files
which include it.

Signed-off-by: Laurence Withers <lwithers@guralp.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Sanjeev Premi
5626f336ca omap3evm: eth: Include functions only when necessary
These functions are not required when CONFIG_CMD_NET
is not defined:
  - setup_net_chip()
  - reset_net_chip()
  - board_eth_init()

This patch wraps them in #ifdef CONFIG_CMD_NET...#endif

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Sriramakrishnan
c06825873d omap3evm: Update ethernet reset sequence for Rev.G board
The GPIO pin used for resetting the external LAN chip has
changed for Rev.G board.

The patch uses generic gpio API instead of direct access
to corresponding registers.

Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:18 +02:00
Sanjeev Premi
6921b314a8 omap3evm: eth: split function setup_net_chip
In current implementation, the function sets up the ethernet
chip and resets it. The steps to reset depend upon the board
revision.

The patch moves the reset actions to new function reset_net_chip().

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:18 +02:00
Sanjeev Premi
80bb756dbe omap3: Include array definition only when it is used
The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().

Enclose definition of this array in #ifdef...#endif for
the same.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:18 +02:00
Wolfgang Denk
d50a8f45c9 Merge branch 'master' of git://git.denx.de/u-boot-mmc
* 'master' of git://git.denx.de/u-boot-mmc:
  Revert "AT91:mmc:fix multiple read/write error"
2011-08-02 22:39:36 +02:00
Simon Guinot
7432ed05a3 sf: macronix: disable write protection when initializing
Signed-off-by: Simon Guinot <sguinot@lacie.com>
2011-08-02 22:02:34 +02:00
Shaohui Xie
9445ce0873 sf: spansion: add support for S25FL129P_64K
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
2011-08-02 22:01:27 +02:00
Macpaul Lin
2d722e0549 mtd/spi/macronix.c: add MX25L4005 and MX25L8005
Add support of MX25L4005 and MX25L8005 according to the datasheet
http://www.mct.net/download/macronix/mx25l8005.pdf

This patch has been tested with MX25L4005 and MX25L8005

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2011-08-02 21:54:40 +02:00
Wolfgang Denk
0886eef9ba Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
  net/4xx: Install interrupt handler after driver registration
2011-08-02 21:52:21 +02:00
Wolfgang Denk
1902692aa0 Merge branch 'master' of git://git.denx.de/u-boot-blackfin
* 'master' of git://git.denx.de/u-boot-blackfin:
  Blackfin: jtag-console: fix timer usage
  Blackfin: switch to common display_options()
  Blackfin: serial: move early debug strings into .rodata section
  Blackfin: adi boards: also set stderr to nc with helper
  Blackfin: update anomaly lists to latest public info
  Blackfin: serial: convert to bfin_{read,write} helpers
  Blackfin: split out async setup
  Blackfin: adi boards: enable pretty flash progress output
  Blackfin: drop unused dma.h header from start code
  Blackfin: portmux: allow header to be included in assembly files
  Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: enable mmc_spi support
  Blackfin: cm-bf537e/cm-bf537u/tcm-bf537: update network settings
  Blackfin: sync MMR read/write helpers with Linux
  Blackfin: gpio: optimize free path a little
  Blackfin: post: setup default CONFIG_SYS_POST_WORD_ADDR
  Blackfin: uart: fix printf warning
  Blackfin: add init.elf helper code
  Blackfin: dont reset SWRST on newer bf526 parts
  Blackfin: adi boards: enable multi serial support by default
  Blackfin: uart: add multiple serial support
  Blackfin: uart: move debug buffers into local bss
2011-08-02 21:46:53 +02:00
Wolfgang Denk
cc4e6d2556 Merge branch 'master' of git://git.denx.de/u-boot-mips
* 'master' of git://git.denx.de/u-boot-mips:
  README: update MIPS related informations
  MIPS: make cache operation mode configurable
  MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFG
  MIPS: INCA-IP: rename inca-swap-bytes host tool
2011-08-02 21:45:45 +02:00
Wolfgang Denk
982db890e8 tqm834x.c: fix compiler warning
Fix:

tqm834x.c:299: warning: passing argument 1 of 'get_ram_size' discards
qualifiers from pointer target type

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2011-08-02 12:49:17 -05:00
Wolfgang Denk
33a6b9e90b environment.h: fix warning: "CONFIG_ENV_IS_EMBEDDED" redefined
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
2011-08-01 15:20:16 +02:00
Wolfgang Denk
e6a857da74 fpga: constify to fix build warning
Fix compiler warning:

cmd_fpga.c:318: warning: passing argument 3 of 'fit_image_get_data'
from incompatible pointer type

Adding the needed 'const' here entails a whole bunch of additonal
changes all over the FPGA code.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Murray Jensen <Murray.Jensen@csiro.au>
Acked-by: Andre Schwarz<andre.schwarz@matrix-vision.de>
2011-08-01 15:19:40 +02:00
Wolfgang Denk
f6c019c454 Unify timer_init() and cpu_init() prototypes
Clean up some duplicated prototype declarations.
Get rid of now useless AVR32 initcalls.h file.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
2011-08-01 15:10:15 +02:00
seedshope
5589073a16 ARM: fix error: conflicting types for 'setenv'
Also remove bogus comment.

Signed-off-by: Zhong hongbo <bocui107@gmail.com>
Changed commit message
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
2011-08-01 15:07:06 +02:00
Wolfgang Denk
5791293986 cfb_console.c: checkpatch cleanup
Fix the following:

ERROR: do not initialise statics to 0 or NULL
ERROR: do not use assignment in if condition

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-08-01 15:03:07 +02:00
Wolfgang Denk
72c65f6f6d cfb_console.c: drop custom PRINTD() and use debug() instead
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-08-01 14:58:55 +02:00
Wolfgang Denk
64e40d72ea Cosmetic: reformat drivers/video/cfb_console.c
Run cfb_console.c through indent and manually fix some of he
deficiencies of the automatic line breaking.

Fix multiline comments, excessive line spacing and such.

No changes to code done.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-08-01 14:58:41 +02:00
Daniel Schwierzeck
92bbd64e39 README: update MIPS related informations
Amend section 'Directory Hierarchy' for current MIPS directory.
Describe config options for MIPS.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-07-31 23:26:41 +09:00
Daniel Schwierzeck
ab2a98b117 MIPS: make cache operation mode configurable
Currently the cache operation mode is hard-coded to
CONF_CM_CACHABLE_NONCOHERENT. This is not appropiate for CPUs or SOCs
which operate at a different mode.

This patch makes the cache operation mode configurable via board config.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-07-31 23:26:41 +09:00
Daniel Schwierzeck
7185adb48e MIPS: rename INFINEON_EBU_BOOTCFG to CONFIG_SYS_XWAY_EBU_BOOTFG
This define is a board-specific config option and should be
renamed to follow the U-Boot naming convention. Additionally,
add an explaining comment for this option.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-07-31 23:26:41 +09:00
Daniel Schwierzeck
60b74bde92 MIPS: INCA-IP: rename inca-swap-bytes host tool
The INCA-IP SoC belongs to the Lantiq XWAY SoC product portfolio.
For the upcoming support of other Lantiq SoC devices this tool should
not solely depend on the INCA-IP board.

Rename the tool to xway-swap-bytes and add an config option
to enable compilation optionally.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Thomas Langer <thomas.langer@lantiq.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-07-31 23:25:41 +09:00
Wolfgang Denk
dd620b2633 Merge branch 'master' of /home/wd/git/u-boot/custodians
* 'master' of /home/wd/git/u-boot/custodians:
  powerpc/8xxx: Remove dependency on <usb.h>
  powerpc/85xx: enable USB2 gadget mode for corenet ds board
  powerpc/85xx: verify the device tree before booting Linux
  MPC8xxx: drop redundant boot messages
  powerpc/85xx: Fix build failure for P1023RDS
  powerpc/p2041rdb: Enable SATA support
  powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500
  powerpc/85xx: Fix up clock_freq property in CAN node of dts
  85xx: enable FDT support for STX SSA board
  powerpc/85xx: provide 85xx flush_icache for cmd_cache
  powerpc/p2041rdb: Enable backside L2 cache support
  powerpc/85xx: Handle the lack of L2 cache on P2040/P2040E
  powerpc/85xx: Add support for P2041[e] XAUI in SERDES
  powerpc/85xx: Rename P2040 id & SERDES to P2041
  powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
  powerpc/85xx: Fix setting of EPAPR_MAGIC value
2011-07-30 01:39:14 +02:00
Wolfgang Denk
84b5e8022e Constify getenv(), setenv() and hash code functions
This is needed to get rid of build warnings like

main.c:311: warning: passing argument 2 of 'setenv' discards qualifiers from pointer target type

which result from commit 09c2e90 "unify version_string".

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andreas Biemann <andreas.devel@googlemail.com>
2011-07-30 01:37:44 +02:00
Wolfgang Denk
7ca9296e1b README: udate Coding Style description to current status quo
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-07-30 01:36:25 +02:00
Kumar Gala
5756736176 powerpc/8xxx: Remove dependency on <usb.h>
We used <usb.h> for USB_MAX_DEVICE.  However this requires we actual
build in support for USB into u-boot (which should not be required for
device tree fixup).

At this time no FSL SoC that utilizies this code (83xx/85xx) has more
than 2 USB controllers.  So we replace USB_MAX_DEVICE with a local
define FSL_MAX_NUM_USB_CTRLS.

If/when a device shows up with more than 2 controllers we can easily
bump this value or refactor into a proper define per SoC.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 16:04:56 -05:00
Shaohui Xie
a3a3e7b2c3 powerpc/85xx: enable USB2 gadget mode for corenet ds board
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:43 -05:00
Timur Tabi
90f89f099d powerpc/85xx: verify the device tree before booting Linux
Introduce ft_verify_fdt(), a function that is called after the device tree
has been fixed up, that displays warning messages if there is a mismatch
between the physical addresses of some devices that U-Boot has configured
with what the device tree says the addresses are.

This is a particular problem when booting a 36-bit device tree from a
32-bit U-Boot (or vice versa), because the physical address of CCSR is
wrong in the device tree.  When the operating system boots, no messages are
displayed, so the user generally has no idea what's wrong.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Wolfgang Denk
21cd5815a7 MPC8xxx: drop redundant boot messages
Current code would print RAM size information like this:

	DRAM:  DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)

Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:

	DRAM:  256 MiB (DDR1, 64-bit, CL=2, ECC off)

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Kumar Gala
74d9d5239f powerpc/85xx: Fix build failure for P1023RDS
When we added the fman fdt fixup we forgot to fixup the P1023RDS
platform.  So we would get:

fdt.c: In function 'fdt_fixup_fman_firmware':
fdt.c:465:15: error: 'CONFIG_SYS_FMAN_FW_LENGTH' undeclared (first use in this function)
fdt.c:465:15: note: each undeclared identifier is reported only once for each function it appears in

Add the needed #defines in P1023RDS.h to fix this.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Mingkai Hu
aa7f281ce4 powerpc/p2041rdb: Enable SATA support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Kumar Gala
8992738db7 powerpc/85xx: Cleanup handling of PVR detection for e500/e500mc/e5500
At some point we broke the detection of e500v1 class cores.  Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:39 -05:00
Bhaskar Upadhaya
65bb8b060a powerpc/85xx: Fix up clock_freq property in CAN node of dts
Fix up the device tree property associated with the Flexcan clock
frequency. This property is used to calculate the bit timing parameters
for Flexcan.

Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Wolfgang Denk
28415b62d1 85xx: enable FDT support for STX SSA board
We also have to shift TEXT_BASE to accomodate for the additional
code size.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Matthew McClintock
0a9fe8ee7e powerpc/85xx: provide 85xx flush_icache for cmd_cache
This provides a function that will override the weak function
flush_icache to let 85xx boards to flush the icache

cc: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
2011-07-29 08:53:38 -05:00
Mingkai Hu
cd420e0b2a powerpc/p2041rdb: Enable backside L2 cache support
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Kumar Gala
acf3f8da98 powerpc/85xx: Handle the lack of L2 cache on P2040/P2040E
The P2040/P2040E have no L2 cache.  So we utilize the SVR to determine
if we are one of these devices and skip the L2 init code in cpu_init.c
and release.  For the device tree we skip the updating of the L2 cache
properties but we still update the chain of caches so the CPC/L3 node
can be properly updated.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Kumar Gala
db564bccef powerpc/85xx: Add support for P2041[e] XAUI in SERDES
We add XAUI_FM1 into the SERDES tables for P2041[e] devices.  However
for the P2040[e] devices that dont support XAUI we handle this at
runtime via SVR checks.  If we are on a P2040[e] device the SERDES
functions will behave as follows:

is_serdes_prtcl_valid() will always report invalid if prtcl passed in is
XAUI_FM1.

serdes_get_prtcl() will report NONE if the prtcl in the table is set to
XAUI_FM1.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Kumar Gala
88b91f2d3b powerpc/85xx: Rename P2040 id & SERDES to P2041
P2041 is the superset part that covers both P2040 & P2041.  The only
difference between the two devices is that P2041 supports 10g/XAUI and
has an L2 cache.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:37 -05:00
Stephen George
f110fe940c powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.

Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:37 -05:00
Kumar Gala
70bfb032ec powerpc/85xx: Fix setting of EPAPR_MAGIC value
Had a typo in the ifdef for 85xx, should be CONFIG_MPC85xx for it to get
triggered.  Was pull in the non-BookE magic number.

Reported-by: John Cortell
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:37 -05:00
Andreas Bießmann
ce0f709bcd cfb_console: fix build breakage
Commit 09c2e90c11 "unify version_string"
introduced a build breakage in cfb_console.c

---8<---
cfb_console.c:1497: warning: format '%s' expects type 'char *', but
argument 3 has type 'const char (*)[]'
--->8---

Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
2011-07-29 11:28:26 +02:00