The cpu_eth_init() is only used by the legacy ethernet driver framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Map all resource for R5 to operate properly.
The patch is done based on the commit 23f7b1a776 ("armv7R: K3: am654:
Enable MPU regions") which also map the whole 4GB at first and then change
mapping for DDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It was protected just for SPL_OS_BOOT but this function is only called when
SPL_ATF is enabled that's why change macro name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Value of shunt resistor for INA226s that monitor VCCINT and VCC_SOC power
rails are incorrect. This patch corrects those values.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
There is 2nd pca9548 mux on I2C1 bus that controls SFP0, SFP1, and QSFP1
ports. Channel 0 and 1 are connected to J287 connector for SFP0 & SFP1, and
channel 2 is connected to J288 connector for QSFP1.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add read/write memory utilities for 16 and 32 bits. Add these
api's for both little and big endian systems similar to arm
architecture.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not source xilinx board Kconfig by other boards. These configs should be
available only when Xilinx platforms are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there is no Bank I so instances 8 and 9 need to be
incremented as a minimum change.
An alternative (less opaque) implementation would be to use a bank-name
property instead but this would require modifying the driver code too.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the <reg> property,
while the device tree defines the address relative to a declaration in
the parent pinctrl node.
Changing the device tree to fix a driver issue would normally be wrong,
however:
- I have run the first version of U-Boot in which this driver appears
(v2016.03) and the same problem exists, so this is not a regression;
- There is no code that references a parent device tree node that might
suggest the intent of the author was to parse the DT as it exists now;
- The equivalent Linux PIC32 GPIO driver also uses absolute addresses
for the GPIO <reg> property. This change brings the U-Boot DT more
into line with Linux.
Additionally, the data sheet (Microchip ref. 60001361H) shows that the
register set to control a GPIO bank spans 0xE0 bytes, but the device
tree specified size is only 0x48 bytes.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The PIC32MZ DA Starter Kit does not need the card detect workaround
because the SDCD signal line is connected properly. Disable the
workaround in this case.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
Add boolean input argument @no_map to helper function
fdtdec_add_reserved_memory() to add or not "no-map" property
for an added reserved memory node.
Property no-map is used by the Linux kernel to not not map memory
in its static memory mapping. It is needed for example for the|
consistency of system non-cached memory and to prevent speculative
accesses to some firewalled memory.
No functional change. A later change will update to OPTEE library to
add no-map property to OP-TEE reserved memory nodes.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present 64-bit sunxi boards use the Makefile to create a FIT, using
USE_SPL_FIT_GENERATOR. This is deprecated.
Update sunxi to use binman instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Linking a U-Boot larger than 1MB fails with PIE enabled:
u-boot/arch/arm/cpu/armv8/start.S:71:(.text+0x3c): relocation
truncated to fit: R_AARCH64_ADR_PREL_LO21 against symbol `__rel_dyn_end'
defined in .bss_start section in u-boot.
This extends the supported range by using adrp & add to load symbols
early while starting up.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PIE requires a 4K aligned load address. If this is not met, trap
the startup sequence in a WFI loop rather than running into obscure
failures.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mention the requirement of 4K aligned load addresses in the
help section for the POSITION_INDEPENDENT option.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Atmel PIT timer is not available for next products that
have another timer hardware block.
To be able to use the common at91 code, guard the code that uses PIT
by ifdefs.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We already have a function to retrieve the mac address from one EEPROM.
For boards with a second Ethernet interface, however, we would
require another EEPROM with a second unique MAC address.
Introduce at91_set_eth1addr which will look for a second EEPROM
and set the 'eth1addr' variable with the obtained MAC address.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>