The Tegra keyboard controller provides a simple interface to a matrix
keyboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add tegra_i2c_get_dvc_bus_num() to obtain the I2C bus number of DVC bus.
This allows us to talk to the PMU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a definition of the memory controller node according to the bindings
here:
http://patchwork.ozlabs.org/patch/132928/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Save SDRAM parameters into the warmboot scratch registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add code to set up the warm boot area in the Tegra CPU ready for a
resume after suspend.
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Power supplies must be adjusted in line with clock frequency. This code
provides a simple routine to set the voltage to allow operation at maximum
frequency.
- Split PMU code into separate TPS6586X driver
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for setting up the memory controller parameters. Boards
can set up an appropriate table in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a basic header file for this register, to be filled in as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to know which type of chip we are running on - the Tegra
family has several SKUs. This can be determined by reading a
fuse register, so add this function to ap20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These headers provide access to additional Tegra features.
flow - start/stop CPUs
sdram - parameters for SDRAM
fuse - access to on-chip fuses / security settings
gp_padctl - pad control and general purpose registers
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Provides an interface to aes.c for the warmboot code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Yen Lin <yelin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add clock_ll_read_pll() to read PLL parameters and clock_get_osc_bypass()
to find out if the Oscillator is bypassed. These are needed by warmboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to include this from board code, so move the header into
an easily-accessible location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This macro is generally useful to make it available in common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Do not define serial_putc() and serial_puts() calls if
CONFIG_SPL_SERIAL_SUPPORT is set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This code is part of battery boot support for i.MX28.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
If the LCD controller is on before the CPU goes into reset, the traffic on LCDIF
data pins interferes with the BootROM's boot mode sampling. So shut the
controller down.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Pass memory size from SPL via structure located in SRAM instead of SCRATCH
registers. This allows passing more data about boot from SPL to U-Boot, like the
boot mode pads configuration.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
After an update to the MX51 reference manual (Rev. 5), the
values of the PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH
are now clearly wrong:
"Bit 13:
High / Low Output Voltage Range. This bit selects the output voltage mode for
SD2_CMD. 0 High output voltage mode
1 Low output voltage mode"
The values are currently negated in code - fixed.
Reported-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: David Jander <david.jander@protonic.nl>
Acked-by: David Jander <david.jander@protonic.nl>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This solves issues when larger amount of DRAM is used, like 256MB.
Behave the same in case of CPU bypass as we do in case of EMI
bypass, but wait 15 ms. We need to wait until the clock domain
stabilizes.
This issue seemed to have been caused by not waiting after frobbing
with the CPU bypass, it was unrelated to memory, but had a direct
impact, causing trouble. This was yet another X-File of the
imx-bootlets, sigh. The conclusion is, trying a semi-random delay
(there is delay after the EMI bypass change), the issue is fixed.
Another possible explanation is that we do not do the "simple memory
test" FSL does in their imx-bootlets (1000 R/W cycles to/from piece of
the memory, while also outputing something on the serial port). This
might have caused the similar delay in the imx-bootlets and therefore
they didn't need to add this explicitly.
For now, this seems good fix enough, but to me, whole that memory
init code in imx-bootlets is completely flunked and it'd need deeper
investigation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
FSL 2.6.35 kernel assumes that the bootloader passes the CONFIG_REVISION_TAG information.
The kernel uses this data to distinguish between Dialog versus mc34708 based boards,
and also to distinguish between revA and revB of the mc34708 based boards.
Suggested-by: Yu Li <yk@magniel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
types.h must be included in imx-regs.h if one wants to include
imx-regs.h in a board configuration file. That for one's part is
necessary, if one wants to use addresses defined in imx-regs.h.
For example, fsl_esdhc.c needs CONFIG_SYS_FSL_ESDHC_ADDR defined and
a proper thing is to define it with IMX_MMC_SDHCx_BASE in board
configuration file. This patch fixes the build in that case.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Defining CONFIG_FSL_ESDHC brings in a call to get_clocks, so let's
implement get_clocks function. This is how it seems to be implemented
elsewhere.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
Init the core regulator voltage to 1.2V. This is required for the correct
functioning of the GPU and when the ARM LDO is set to 1.225V. This is a
workaround to fix some memory clock jitter.
Note: This should be but can't be done in the DCD. The bootloader
prevents access to the ANATOP registers.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
This reverts commit 69d26d09de.
Apparently, this commit got mainline only because of out-of-tree
port and causes breakage on board that is mainline. Revert.
Reason:
* The OOT board has 512MB of DRAM, enabling this additional address
line enabled it to work fine with 512MB of RAM.
* Every mainline port has max. 256MB of DRAM, therefore this revert
has no impact on any mainline port
* Though this caused a problem with new M28 board with 256MB of DRAM
where the chips are wired differently. The patch-to-be-reverted
caused the DRAM to behave like this:
[128MB chunk #1][128MB chunk #1 again][128MB chunk #2][128MB chunk #2 again]
Therefore to retain the current one-memory-init-rules-them-all situation,
revert this patch until another board emerges and will actually be pushed
mainline that needs different setup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Print CPU information within board_late_init().
This is in preparation for adding 1GHz support, which requires programming a PMIC
via I2C. As I2C is only available after relocation, print the CPU information
later at board_late_init(), so that the CPU frequency can be printed correctly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
mx5: Add clock config interface
Add clock config interface support, so that we
can configure CPU or DDR clock in the later init
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
get_ahb_clk() is a common function between mx5 and mx6.
Place it into imx-common directory.
Cc: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The MX53 SATA interface can use an internal clock (USB PHY1)
instead of an external clock. This is an undocumented feature, but used
on most Freescale's evaluation boards, such as MX53-loco.
As stated by Freescale's support:
Fuses (but not pins) may be used to configure SATA clocks.
Particularly the i.MX53 Fuse_Map contains the next information
about configuring SATA clocks :
SATA_ALT_REF_CLK[1:0] (offset 0x180C)
'00' - 100MHz (External)
'01' - 50MHz (External)
'10' - 120MHz, internal (USB PHY)
'11' - Reserved
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Add base address and MXC_SATA_CLK to return
the clock used for the SATA controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI
based LCD Panel could be used with it. This patch supports MIPI-DSI driver
based Samsung SoC chip.
LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
board file and LCD panel driver specific function registered to mipi_dsim_ddi
structure at lcd panel init function called system init.
In the MIPI-DSI driver, find lcd panel driver by using registered
lcd panel name, and then initialize lcd panel driver.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
This patch support EXYNOS FB and FIMD display drivers.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
To sets up lcd and mipi clock in EXYNOS display driver, added clock interface.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This is definitions of system registers and power mananagement registers for EXYNOS SoC.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
TZPC IP is common across Exynos based SoC'c. Renaming exynos5_tzpc
in arch/arm/include/asm/arch-exynos/tzpc.h to exynos_tzpc will allow generic
usase of tzpc.
Also modify board/samsung/smdk5250/tzpc_init.c to use exynos_tzpc.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This rule confirms that if we're on ARM and we have enabled THUMB builds
that we have a new enough toolchain to produce a working binary.
Changes in v2:
- Switch to ALL-$(CONFIG_SYS_THUMB_BUILD) in arch/arm/config.mk (Mike F)
- Simplfy checkthumb test after doing the above
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Avoid using __attribute__ ((__packed__)) unless it's
absolutely necessary. "packed" will remove alignment
requirements for the respective objects and may cause
alignment issues unless alignment is also enforced
using a pragma.
Here, these packed attributes were causing alignment
faults in Thumb build.
Signed-off-by: Aneesh V <aneesh@ti.com>
Enable -march=armv7-a for armv7 platforms if the tool-chain
supports it. This in turn results in Thumb-2 code generated
for these platforms if CONFIG_SYS_THUMB_BUILD is enabled.
Signed-off-by: Aneesh V <aneesh@ti.com>
Enable Thumb build and ARM-Thumb interworking based on the new
config flag CONFIG_SYS_THUMB_BUILD
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Use ENTRY and ENDPROC with assembly functions to ensure
necessary assembler directives for all functions.
Signed-off-by: Aneesh V <aneesh@ti.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This will add ARM specific over-rides for the defines
from linux/linkage.h
Signed-off-by: Aneesh V <aneesh@ti.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
Warm reset is not functional in case of omap5430ES1.0.
So override the weak reset_cpu function to use
cold reset instead.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The reset.S has the function to do a warm reset on OMAP
based socs. Moving this to a reset.c file so that this
acts a common layer to add any reset related functionality
for the future.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
PD_TIM bit field which specifies the power down timing is defined
to occupy bits 8-11, where as it is actually from 12-15 bits.
So correcting this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Make the sysctrl structure common, so that it can
be used in generic functions across socs.
Also change the base address of the system control module, to
include all the registers and not simply the io regs.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The full internal SRAM of size 128kb is public in the case of OMAP5 soc.
So change the base address accordingly.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The different silicon revision variable names was defined for OMAP4 and
OMAP5 socs. Making the variable common so that some code can be
made generic.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The break statement is missing in init_omap_revision function, resulting
in a wrong revision identification. So fixing this.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The nominal opp vdd values as recommended for
ES1.0 silicon is set for mpu, core, mm domains using palmas.
Also used the right sequence to enable the vcores as per
a previous patch from Nishant Menon, which can be dropped now.
http://lists.denx.de/pipermail/u-boot/2012-March/119151.html
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.
As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This change adds initial support for NXP LPC32x0 SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: bfin_sdh: drop dos part hardcode
Blackfin: move gd/bd to bss by default
Blackfin: gd_t: relocate volatile markings
* 'master' of git://git.denx.de/u-boot-nds32:
board/adp-ag102: add configuration of adp-ag102
board/adp-ag102: add board specific files
nds32/ag102: add ag102 soc support
nds32/ag102: add header support of ag102 soc
* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
CMD: Remove CMD_LOG, it's unused
CMD: Fix typo KGBD -> KGDB on debris board
CMD: Drop CONFIG_CMD_EMMC, it's not used
CMD: Drop CONFIG_CMD_DFL, it's not used
CMD: Drop CMD_DCR, it's not used
CMD: Drop CMD_CAN, it's not used
CMD: Remove CMD_AUTOSCRIPT, it's not used
AT91: Drop AT91_SPIMUX command from cmd_all
The CCSR relocation code in start.S writes to MAS7 on all e500 parts, but
that register does not exist on e500v1.
Signed-off-by: Timur Tabi <timur@freescale.com>
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.
Master needs to:
1. Set outbound SRIO windows in order to configure slave's registers
for the core's releasing.
2. Check the SRIO port status when release slave core, if no errors,
will implement the process of the slave core's releasing.
Slave needs to:
1. Set all the cores in holdoff by RCW.
2. Be powered on before master's boot.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.
Master needs to:
1. Put the slave's ucode image into it's own memory space.
2. Set an inbound SRIO window covered slave's ucode stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.
The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image in master NOR flash.
3. Normally boot from local NOR flash.
4. Configure SRIO switch system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to SRIO1 or SRIO2 by RCW.
3. RCW should configure the SerDes, SRIO interfaces correctly.
4. Slave must be powered on after master's boot.
For the master module, need to finish these processes:
1. Initialize the SRIO port and address space.
2. Set inbound SRIO windows covered slave's u-boot image stored in
master's NOR flash.
3. Master's u-boot image should be generated specifically by
make xxxx_SRIOBOOT_MASTER_config
4. Master must boot first, and then slave can be powered on.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Currently "u-boot", the elf file generated via u-boot-nand.lds does not
contain required debug information i.e. .debug_{line, info, abbrev, aranges,
ranges} into their respective _global_ sections.
The original ld script line arch/powerpc/cpu/mpc85xx/start.o
KEEP(*(.bootpg)) is not entirely correct because the start.o file is already
processed by the linker,therefore the file wildcard in "KEEP(*(.bootpg))" will
not process start.o again for bootpg.
So Fix u-boot-nand.lds to generate these debug information.
Signed-off-by: Anmol Paralkar <b07584@freescale.com>
Signed-off-by: John Russo <John.Russo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
NAND SPL code never compile the vector table.
So no need to setup interrupt vector table for NAND SPL.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
After relocation of vector table in SDRAM's lower address, IVORs value should
be updated with new handler addresses.
As vector tables are relocated to 0x100,0x200... 0xf00 address in DDR.IVORs
are updated with 0x100, 0x200,....f00 hard-coded values.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
For e500 and e500v2 architecturees processor IVPR address should be alinged on
64K boundary.
in start.S, CONFIG_SYS_MONITOR_BASE is stored blindly in IVPR assuming it to be
64K aligned. It may not be true always. If it is not aligned, IVPR + IVORs may
not point to an exception handler.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platforms
The driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platforms
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Now that run_command() handles both parsers, clean up sandbox to use it.
This fixes a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized
do_bootm_linux for ARM. During the re-organization, the call to
fdt_fixup_ethernet() was removed. I assume this was useful, so add it
back.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Commit 0a672d4 "arm: Add Prep subcommand support to bootm" re-organized
do_bootm_linux() for ARM. During the re-organization, the code to pass
the device tree to the kernel was removed. Add it back. This restores
the ability to boot a kernel using device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Allen Martin <amartin@nvidia.com>
We don't need these setup manually, so let the bss do the rest. On
Blackfin systems, we clear the bss before executing any C code that
would use these, so this should be fine.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This makes Blackfin behave the same as other ports, and fixes many gcc
warnings that show up with 4.5+:
board.c:40:1: warning: optimization may eliminate reads and/or
writes to register variables
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add device address offsets header of ag102 soc.
Add ag102 into mach-types.h.
Add asm-offsets.c for helping convert C headers into asm.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
We certainly don't want the compiler to reorganise the code for dcache flushing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Stefano Babic <sbabic@denx.de>
As well as pushed for ARM926EJS, we certainly don't want
the compiler to reorganise the code for dcache flushing
Fix checkpatch warnings as well.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Freescale SOCs require an header to u-boot.bin
The patch adds u-boot.imx to the default targets
if the imx file is set (IMX_CONFIG).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
CC: Loïc Minier <loic.minier@linaro.org>
CC: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Dirk Behme <dirk.behme@googlemail.com>
This fixes the issue where mxs_dma_init() was called either twice or never,
without introducing any new init hooks.
The idea is to allow each and every device using the APBH DMA block to
configure and request only the channels it uses, instead of making it call init
for all the channels as is now.
The common DMA block init part, which only configures the block, is then called
from CPUs arch_cpu_init() call.
NOTE: This patch depends on:
http://patchwork.ozlabs.org/patch/150957/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Misaligned warnings are useful to debug faulty drivers.
A misaligned warning is printed also when the driver
is correct - use debug() instead of printf().
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Since commit 5c1ad3e6f8
(net: fec_mxc: allow use with cache enabled) the FEC_MXC
driver uses flush_dcache_range() and invalidate_dcache_range()
functions. This driver is also configured for ARM1136 based
'flea3' and 'mx35pdk' boards which currently do not build
as there are no ARM1136 specific flush_dcache_range() and
invalidate_dcache_range() functions. Add various ARM1136
cache functions to fix building for 'flea3' and 'mx35pdk'.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging:
LMB: Fix undefined lmb_reserve() on non-lmb platforms
MIPS: fix endianess handling
MIPS: fix inconsistency in config option for cache operation mode
MIPS: board.c: fix init of flash data in bd_info
* 'master' of git://git.denx.de/u-boot-nios:
nios2 - adjust gbl data off to account for bd_info
nios2: implement get_ticks and get_tbclk
nios2: add flush_dcache_range function
Make endianess of target CPU configurable. Use the new config
option for dbau1550_el and pb1000 boards.
Adapt linking of standalone applications to pass through
endianess options to LD.
Build tested with:
- ELDK 4 mips_4KC- and mips4KCle
- Sourcery CodeBench Lite 2011.03-93
With this patch all 26 MIPS boards can be compiled now in one step by
running "MAKEALL -a mips".
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Commit ab2a98b117 missed to
use the new config option in dcache_enable().
Fix this to avoid inconsistencies if someone wants to disable
and enable D-caches.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Boards with CONFIG_SYS_NO_FLASH should not forced to define
CONFIG_SYS_FLASH_BASE. In this case the flash data in bd_info
should be initialized with 0 like the other archs do.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
This command boots Linux zImage from where the zImage is loaded to. Passing
initrd and fdt is supported.
Tested on i.MX28 based DENX M28EVK
Tested on PXA270 based Voipac PXA270.
NOTE: This currently only supports ARM, but other architectures can be easily
added by defining bootz_setup().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: albert.u.boot@aribaud.net
Cc: afleming@gmail.com,
Cc: Simon Glass <sjg@chromium.org>,
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
* 'master' of git://git.denx.de/u-boot-arm: (146 commits)
arm: Use common .lds file where possible
arm: add a common .lds link script
arm: Remove unneeded setting of LDCSRIPT
Define CPUDIR for the .lds link script
arm: Remove zipitz2 link script
Allow arch directory to contain .lds without requiring Makefile
OMAP: Remove omap1610inn-based boards
arch/arm/cpu/armv7/omap-common/clocks-common.c: Fix build warnings
board/ti/beagle/beagle.c: Fix build warnings
sdrc.c: Fix typo in do_sdrc_init() for SPL
tegra: i2c: Add I2C driver
tegra: fdt: i2c: Add extra I2C bindings for U-Boot
tegra: i2c: Select I2C ordering for Seaboard
tegra: i2c: Enable I2C on Seaboard
tegra: i2c: Select number of controllers for Tegra2 boards
tegra: i2c: Initialise I2C on Nvidia boards
tegra: Enhance clock support to handle 16-bit clock divisors
fdt: Add function to allow aliases to refer to multiple nodes
tegra: Rename NV_PA_PMC_BASE to TEGRA2_PMC_BASE
tegra: fdt: Enable FDT support for Ventana
tegra: fdt: Enable FDT support for Seaboard
tegra: usb: Enable USB on Seaboard
tegra: usb: Add common USB defines for tegra2 boards
tegra: usb: Add USB support to nvidia boards
arm: Check for valid FDT after console is up
fdt: Avoid early panic() when there is no FDT present
tegra: usb: Add support for Tegra USB peripheral
tegra: fdt: Add function to return peripheral/clock ID
usb: Add support for txfifo threshold
tegra: usb: fdt: Add USB definitions for Tegra2 Seaboard
tegra: usb: fdt: Add additional device tree definitions for USB ports
tegra: fdt: Add clock bindings for Tegra2 Seaboard
tegra: fdt: Add clock bindings
tegra: fdt: Add additional USB binding
fdt: Add tegra-usb bindings file from linux
fdt: Add staging area for device tree binding documentation
tegra: fdt: Add device tree file for Tegra2 Seaboard from kernel
tegra: fdt: Add Tegra2x device tree file from kernel
arm: fdt: Add skeleton device tree file from kernel
fdt: Add basic support for decoding GPIO definitions
fdt: Add functions to access phandles, arrays and bools
fdt: Tidy up a few fdtdec problems
fdt: Add tests for fdtdec
fdt: Add fdtdec_find_aliases() to deal with alias nodes
arm: Tegra2: Fix ELDK42 gcc failure with inline asm stack pointer load
net: fec_mxc: allow use with cache enabled
net: force PKTALIGN to ARCH_DMA_MINALIGN
i.MX28: Enable caches by default
i.MX28: Make use of the bounce buffer
i.MX28: Do data transfers via DMA in MMC driver
MMC: Implement generic bounce buffer
i.MX28: Add cache support to MXS NAND driver
i.MX28: Add cache support into the APBH DMA driver
ARM926EJS: Implement cache operations
board/vpac270/onenand.c: Fix build errors
nhk8815: fix build errors
atmel-boards: add missing atmel_mci.h
ARM: highbank: setup env from boot source register
ARM: highbank: change env config to use nvram
ARM: highbank: add reset support
ARM: highbank: Add boot counter support
ARM: highbank: change TEXT_BASE to 0x8000
ARM: highbank: fix us_to_tick calculation
ARM: highbank: add missing get_tbclk
ARM: highbank: fix warning for calxedaxgmac_initialize
net: calxedaxgmac: fix build due to missing __aligned definition
EXYNOS: Add structure for Exynos4 DMC
EXYNOS: SMDK5250: Support all 4 UARTs
ARM: fix s3c2410 timer code
ARM: davinci: fixes for cam_enc_4xx board
omap3_spi: receive transmit mode
calimain, enbw_cmc: Fix typo in comments
Davinci: ea20: use gpio framework to access gpios
OMAP3: mt_ventoux: sets its own mtdparts
OMAP3: mt_ventoux: updated timing for FPGA
twl4030: fix potential power supply handling issues
NAND: TI: fix warnings in omap_gpmc.c
cam_enc_4xx: Rename 'images' to 'imgs'
arm: Add Prep subcommand support to bootm
OMAP3: twister: add support to boot Linux from SPL
SPL: call cleanup_before_linux() before booting Linux
OMAP3: SPL: do not call I2C init if no I2C is set.
Add cache functions to SPL for armv7
devkit8000: Implement and activate direct OS boot
omap/spl: change output of spl_parse_image_header
omap-common/spl: Add linux boot to SPL
devkit8000/spl: init GPMC for dm9000 in SPL
omap-common: Add NAND SPL linux booting
devkit8000: add config for spl command
Add cmd_spl command
mx53ard: Initialize return code with error
mx53: Make PLL2 to be the parent of UART clock
configs: imx: Use CONFIG_SF_DEFAULT_CS
mx28evk: Provide default values for SPI bus and chip select
USB: ehci-mx6: Add proper IO accessors
mx6: Read silicon revision from register
i.MX28: Drop __naked function from spl_mem_init
mxs_spi: Return proper timeout error
i.MX28: Make the stabilization delays shorter
pmic_i2c: Return error in case of invalid pmic_i2c_tx_num
mx6: Remove duplicate definition of ANATOP_BASE_ADDR
mx6: Fix reset cause for Power On Reset case
i.MX6: mx6qsabrelite: add MACH_TYPE_MX6Q_SABRELITE
i.MX6: mx6q_sabrelite: add CONFIG_REVISION_TAG
i.MX28: Enable additional DRAM address bits
mx6q: mx6qsabrelite: setup_spi() should be called in board_init to allow use for environment
mx31: add "ARM11P power gating" to get_reset_cause
mx31pdk: Fix CONFIG_SYS_MEMTEST_END
efikamx: Fix CONFIG_SYS_MEMTEST_END
mx53smd: Fix CONFIG_SYS_MEMTEST_END
mx53evk: Fix CONFIG_SYS_MEMTEST_END
mx51evk: Fix CONFIG_SYS_MEMTEST_END
i.MX6: mx6qsabrelite: add ext2 support
imximage: Remove overwriting of flash_offset
IXP: Fix GPIO_INT_ACT_LOW_SET()
IXP: Fix NAND build warning on PDNB3 and SCPU
IXP: Move PDNB3 and SCPU from Makefile to boards.cfg
IXP: Squash warnings in IXP NPE
IXP: Fix missing MACH_TYPE_{ACTUX?,PNB3,DVLHOST}
IXP: Make IXP buildable with arm-linux- toolchains
Examples: Properly append LDFLAGS to LD command
SPL: Enable YMODEM support on BeagleBone and AM335x EVM
SPL: Add YMODEM over UART load support
SPL: Add README.omap3
README: document more SPL config options
spl.c: Use __noreturn decorator
config.mk: Check for -fstack-usage support
config.mk: Make cc-option create a file under include/generated
...
Each cpu directory currently has its own .lds file. This is only needed
in most cases because the start.o file is in a different subdir.
Now that we can factor out this difference, we can move most cpus over
to the common .lds file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most ARM CPUs use a very similar link script. This adds a basic
script that can be used by most CPUs.
Two new symbols are introduced which are intended to eventually be
defined on all architectures to make things easier for generic relocation
and reduce special-case code for each architecture:
__image_copy_start is the start of the text area (equivalent to the
existing _start on ARM). It marks the start of the region which must be
copied to a new location during relocation. This symbol is called
__text_start on x86 and microblaze.
__image_copy_end is the end of the region which must be copied to a new
location during relocation. It is normally equal to the start of the BSS
region, but this can vary in some cases (SPL?). Making this an explicit
symbol on its own removes any ambiguity and permits common code to always
do the right thing.
This new script makes use of CPUDIR, now defined by both Makefile and
spl/Makefile, to find the directory containing the start.o object file,
which is always placed first in the image.
To permit MMU setup prior to relocation (as used by pxa) we add an area
to the link script which contains space for this. This is taken
from commit 7f4cfcf. CPUs can put the contents in there using their
start.S file. BTW, shouldn't that area be 16KB-aligned?
Signed-off-by: Simon Glass <sjg@chromium.org>
This is set by the top level Makefile anyway, so drop it. This does
have the effect of changing the order - now the board link script will
have preference over the CPU one. But this seems more correct anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix:
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
clocks-common.c: In function 'setup_non_essential_dplls':
clocks-common.c:323:6: warning: variable 'sys_clk_khz' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Tom Rini <trini@ti.com>
Add basic i2c driver for Tegra2 with 8- and 16-bit address support.
The driver requires CONFIG_OF_CONTROL to obtain its configuration
from the device tree.
(Simon Glass: sjg@chromium.org modified for upstream)
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add U-Boot's peripheral clock information to the Tegra20 device tree file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
I2C ports have a 16-bit clock divisor. Add code to handle this special
case so that I2C speeds below 150KHz are supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Change this name to fit with the current convention in the Tegra
header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When using CONFIG_OF_CONTROL, add a check that we have a valid FDT
and panic() if not. This must be done after the console is ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.
Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:
aliases {
/* This defines the order of our USB ports */
usb0 = "/usb@0xc5008000";
usb1 = "/usb@0xc5000000";
};
drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A common requirement is to find the clock ID for a peripheral. This is the
second cell of the 'clocks' property (the first being the phandle itself).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds clock references to the USB part of the device tree for U-Boot,
and marks USB1 as supporting legacy mode (which we disable in the driver).
The USB timing information may vary between boards sometimes, but for
now we hard-code it in C. This is because all current T2x boards use
the same values, we will deal with T3x later and we first need to agree
on the format for this timing information in the fdt and may in fact
decide that it has no place there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds a basic binding for the oscillator and peripheral clocks. The
second cell is the clock number, defined as the bit number within the clock
enable register if the peripheral clock.
This uses the RFC clock bindings from Grant Likely so may change later:
https://lkml.org/lkml/2011/12/12/498
It is taken from Stephen Warren's patch here:
http://patchwork.ozlabs.org/patch/141359/
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
config.mk is updated to provide this file to boards through the
built-in mechanism:
/include/ ARCH_CPU_DTS
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The 4.2.2 gcc in the ELDK42 release doesn't like the direct SP
load using a constant in tegra2_start. Change it to use a load
thru another reg using mov sp, %0 : : "r"(CONST).
Tested on my Seaboard T20-A03, U-Boot loads and runs OK. Also
compiled all tegra2 builds with both gcc 4.2.2 and 4.4.1 OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Implement reset for highbank platform. Reset is triggered via a wfi
instruction, so enabling armv7 for the compiler is necessary.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
udelay calls were off due to failing to convert us to ns. Fix this and drop
the unnecessary shifts since NS_PER_TICK is only 7ns.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The get_tbclk function was missing and the recent commit "common: add
possibility for readline_into_buffer timeout" makes it required.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Add exynos4_dmc structure in dmc.h for exynos4 dram controllor(DMC).
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch fixes the s3c24x0 timer code to work with the ARM
relocation feature.
Signed-off-by: David Mueller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds prep subcommand to bootm implementation of ARM. When bootm is called
with the subcommand prep the function stops right after ATAGS creation and
before announce_and_cleanup.
This is used in command "cmd_spl export"
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
Call i2c initialization in spl_board_init only if I2C
is configured for the board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Simon Schwarz <simonschwarzcor@gmail.com>
This only outputs "Assuming u-boot.bin..." if debug is active.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
This adds Linux booting to the SPL
This depends on CONFIG_MACH_TYPE patch by Igor Grinberg
(http://article.gmane.org/gmane.comp.boot-loaders.u-boot/105809)
Related CONFIGs:
CONFIG_SPL_OS_BOOT
Activates/Deactivates the OS booting feature
CONFIG_SPL_OS_BOOT_KEY
defines the IO-pin number u-boot switch - if pressed u-boot is
booted
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
Address where the kernel boot arguments are expected - this is
normaly RAM-begin + 0x100
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Linux crashes if the GPMC isn't configured for the dm9000.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
This implements booting of Linux from NAND in SPL
Related config parameters:
CONFIG_SYS_NAND_SPL_KERNEL_OFFS
Offset in NAND of direct boot kernel image to use in SPL
CONFIG_SYS_SPL_ARGS_ADDR
Address where the kernel boot arguments are expected - this is
normally RAM-start + 0x100 (on ARM)
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
Change the parent UART clock to be PLL2, so that U-boot can also boot
a Freescale 2.6.35 kernel for mx53.
FSL kernel and U-boot changed the UART parent from PLL3 to PLL2 to avoid
conflicts with IPU clocks, so that the video resolution can be changed
without affecting the UART clock.
On a 2.6.35 kernel the serial console is messed up after IPU driver is loaded
and this patch fixes this problem.
Tested on a mx53loco board booting a FSL kernel and also a mainline kernel.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of hardcoding the mx6 silicon revision, read it in run-time.
Also, besides the silicon version print the mx6 variant type: quad,dual/solo
or solo-lite.
Tested on a mx6qsabrelite, where it shows:
CPU: Freescale i.MX6Q rev1.0 at 792 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
Instead of compiling the function and using the result as a constant, simply use
the constant.
NOTE: This patch works around bug:
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=52546
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cut down the VDDIO/VDDA regulator stabilization delays to 500 uS. That should be
enough according to the datasheet and bootlets.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Robert Deliën <robert@delien.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
After booting mx6qsabrelite from POR the following is reported:
CPU: Freescale i.MX61 family rev1.0 at 792 MHz
Reset cause: unknown reset
This is because both the POR and WDOG bits are set after reset.
Fix this by also checking both bits in the POR case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enables all fourteen address lines for DRAM
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
The GPIO_INT_ACT_LOW_SET was incorrectly handling interrupt lines higher than 7.
This is due to the fact that there are two registers for total of 16 lines.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
IxEthAcc.c: In function ‘ixEthAccInit’:
IxEthAcc.c:105:21: warning: comparison between ‘IxEthDBStatus’ and ‘enum <anonymous>’ [-Wenum-compare]
IxEthDBAPISupport.c: In function ‘ixEthDBPortAddressSet’:
IxEthDBAPISupport.c:633:18: warning: variable ‘ackPortAddressLock’ set but not used [-Wunused-but-set-variable]
IxQMgrDispatcher.c: In function ‘ixQMgrLLPShow’:
IxQMgrDispatcher.c:1194:18: warning: variable ‘q’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Add -EB flag to LD to switch endianness of the linker. This should make armeb
targets buildable again. Also, make use of U-Boot's internal libgcc instead of
toolchain's one, this works around the use of libraries from GCC, which might be
little endian.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch fixes erroneous 32-bit access to registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch introduces an 8-bit register, mx28_register_8, in order to
prepare for fixing erroneous 32-bit wide access of registers
hw_clkctrl_frac0 and hw_clkctrl_frac1.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.
Signed-off-by: Robert Delien <robert@delien.nl>
Fix ptrace and interrupt register overflow warning.
Add missing P0 and P1 (r26 and r27) into register lists.
These register are usually used in OS.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
Add calls to bootstage before and after relocation, and just
before jumping to the OS.
The idea here is you can call bootstage_report() to get a report.
Additionally, if you define CONFIG_BOOTSTAGE_REPORT then a report is
printed automatically by U-Boot just before jumping to the kernel.
Signed-off-by: Simon Glass <sjg@chromium.org>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-avr32:
atmel_mci.h: remove outdated register macros
doc/git-mailrc: add <me> to avr32 alias
ATMEL: remove old atmel_mci driver
ATMEL: use generic mmc framework
All boards are using the gen_atmel_mci driver now, so no need
to carry the old driver around.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
gen_atmel_mci works on AVR32 as well, so no need to use the legacy
mmc driver. This also has the nice side effect of being able to use
SDHC cards an those boards.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This adds simple command-line parsing to sandbox. The idea is that it
sets up the state with options provided, and this state can then be
queried later, as needed.
New flags are declared with the SB_CMDLINE_OPT_SHORT helper macro,
pointers are automatically gathered up in a special section, and
then the core code takes care of gathering them up and processing
at runtime. This way there is no central place where we have to
store a list of flags with ifdefs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In order to pass command line arguments to sandbox we need to be able
to act on them. So take control back at the end of board_init_r() from
where we can call the main loop or do something else.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The state exists through the life of U-Boot. It can be adjusted by command
line options and perhaps later through a config file. It is available to
U-Boot through state_...() calls (within sandbox code).
The primary purpose of this is to contain the "hardware" state. It should
only be used by sandbox internal code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since we provide all our own library calls, the fortification from
glibc just gets in our way (which some distros enable by default).
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This provides a way of simulating GPIOs by setting values which are seen
by the normal gpio_get/set_value() calls.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This provides a way for callers to create files for writing. The flags
are translated at runtime, for the ones we support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This adds support for a controlling fdt, mirroring the ARM implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We should include the sys/time.h header to avoid warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tidy this up as the list is long and likely to get longer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
