Like other Allwinner A64 boards, pinebook also need altering
auto-numbering of mmc2 to mmc1 which is available in common
sunxi dsti file, sunxi-u-boot.dtsi
Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which
takes more precedence for u-boot.dtsi inclusion and it eventually
failed to include the sunxi-u-boot.dtsi.
So, this patch add support to include the sunxi-u-boot.dtsi in the
sun50i-a64-pinebook-u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook
Environment and fastboot mmc devices are configured based on the number
of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA.
If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot
mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device.
But with DM_MMC the mmc devices are numbered as per the dts node
enablement. If there is a chance of having enabling all mmc nodes
in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices
will failed to assign proper emmc device since mmc2 is emmc in most
of the Allwinner platforms.
So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since
aliases take precedence over auto-numbering.
If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe
sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2
the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1
and mmc2 become mmc1
Without aliases of mmc1 = &mmc2;
-------------------------------
MMC: mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2
With aliases of mmc1 = &mmc2;
----------------------------
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... OK
Some platforms like A20 has mmc0...mmc3, but there is no usecases now
for enabling all mmc controllers in any of A20 board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Some Allwinner clock devices have parent clocks and reset gates itself,
which need to be activated for them to work.
Add some code to just assert all resets and enable all clocks given.
This should enable the A80 MMC config clock, which requires both to be
activated. The full CCU devices typically don't require resets, and have
just fixed clocks as their parents. Since we treat both as optional and
enabling fixed clocks is a NOP, this works for all cases, without the need
to differentiate between those clock types.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
If a board DT describes a cd-gpios property, but also marks the storage
as non-removable, we must ignore the GPIO (as Linux does).
Teach the DM_MMC part of the Allwinner MMC driver about the
non-removable DT property, to fix DM_MMC access on the SoPine and
Pine64-LTS board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.
However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.
When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.
Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Now that we have the gate clocks and the reset gates in our new
Allwinner clock driver, let's make use of them in the MMC driver, when
DM_MMC is defined.
We treat the reset device as optional now, as the older SoCs don't
implement it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A80 gates clock already be part of CLK framework, so just
add mod_clk offset with A80 compatible string.
Cc: Rask Ingemann Lambertsen <rask@formelder.dk>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Unlike other Allwinner SoC's, H6 uses a different MMC mod clock offset.
Connect that with the respective compatible string.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add MMC compatible strings for A83T, A64, H5.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The A80 handles resets and clock gates for the MMC devices differently,
outside of the CCU IP block. Consequently we have a separate clock
device with a separate binding for that.
Implement that with the respective clock gates and resets to allow the
A80 taking part in the DM_MMC game.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: fix a80 mmc clock config compatible]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add the MMC clock gates and reset bits for all the Allwinner SoCs.
This allows them to be used by the MMC driver.
We don't advertise the mod clock yet, as this is still handled by the
MMC driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: add V3S, A80 gates/resets]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Enable USB host controllers for Amarula A64-Relic board,
the respective nodes are already present in DTS.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Per Kever Yang, 32768 is a reasonable max size for TPL on RK3288.
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rather than checking for CONFIG_TPL_BUILD and then re-defining
CONFIG_SPL_TEXT_BASE make use of CONFIG_TPL_TEXT_BASE directly.
Cc: York Sun <york.sun@nxp.com>
Cc: Po Liu <po.liu@nxp.com>
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: Timur Tabi <timur@tabi.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
slre_match() checks if caps == NULL. In this case it does not try to
update it. So there is no need to create a buffer caps which we do not
evaluate.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Change multiple usages of 'j' into 'rgn'; fix whitespace/coding style
reported by patman.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
As a follow-up, change the name of the newly introduced function
'lmb_get_unreserved_size' to 'lmb_get_free_size', which is more
appropriate.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix test/lib/lmb.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Handle correctly directory arch/arm/mach-stm32mp/ :
Add a trailing slash to include all files
and subdirectory files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Linux kernel binding is using atmel,24c08 compatible string. On the
other hand there is atmel,24c08a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
These eeproms are available on several ZynqMP development boards.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The dtoc tests need to be adapted to dtoc being changed to output platdata
structs as const, which has been introduced in commit 7d05d3a8e3 ("dtoc:
make generated platdata structs const").
Fixes: 7d05d3a8e3 ("dtoc: make generated platdata structs const")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
I'm working on getting OpenBSD to run on the Atmel SAMA5D3 Xplained.
OpenBSD uses an EFI bootloader, which requires the "load" command to
work, since "fatload" doesn't initialize the EFI memory addresses
properly. To get "load" on the SAMA5D3 version of U-Boot, I propose
adding the CONFIG_CMD_FS_GENERIC option.
Signed-off-by: Greg Czerniak <greg@czerniak.info>
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
In case when the environment on some location is malformed (CRC isn't
matching), there is a chance we won't be able to save the environment to
that location. For example, consider the case when we only have the
environment on eMMC, but it's zeroed out. In that case, we won't be able
to "env save" to it, because of "bad CRC" error. That's happening
because in env_load() function we consider malformed environment as
incorrect one, and defaulting to the location with highest (0)
priority, which can be different from one we are dealing with right now
(e.g., highest priority can be ENV_FAT on SD card, which is not
inserted, but we want to use ENV_MMC on eMMC, where we were booted
from).
This issue began to reproduce after commit d30ba2315a ("u-boot: remove
driver lookup loop from env_save()") on BeagleBone Black, but that
commit didn't introduce the wrong logic, it just changed the behavior
for default location to use, merely revealing this issue.
To fix that, let's implement next logic in env_load():
1. Try to find out correct environment; if found -- use it
2. If working environment wasn't found, but we found malformed one
(with bad CRC), let's use it for further "env save". But make sure
to use malformed environment location with highest priority.
3. If neither correct nor malformed environment was found, let's
default to environment location with highest priority (0)
Steps to reproduce mentioned issue on BeagleBone Black (fixed in this
patch):
1. Boot from SD card and erase eMMC in U-Boot shell:
=> mmc dev 1
=> mmc erase 0 100000
=> gpt write mmc 1 $partitions
2. Write new SPL and U-Boot to eMMC; the rest of eMMC will stay filled
with zeroes
3. Boot from eMMC; try to do:
=> env save
4. Observe the error (incorrect behavior). Correct behavior: environment
should be stored correctly on eMMC, in spite of it has "bad CRC"
Fixes: d30ba2315a ("u-boot: remove driver lookup loop from env_save()")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Callers of env_import*() functions might want to check the case when we
have incorrect environment (with bad CRC). For example, when environment
location is being defined in env_load(), call chain may look like this:
env_load() -> drv->load() = env_mmc_load() -> env_import()
Return code will be passed from env_import() all way up to env_load().
Right now both env_mmc_load() and env_import() return -EIO error code,
so env_load() can't differentiate between two cases:
1. Driver reports the error, because device is not accessible
2. Device is actually accessible, but environment is broken
Let's return -ENOMSG in env_import(), so we can distinguish two cases
mentioned above. It will make it possible to continue working with "bad
CRC" environment (like doing "env save"), instead of considering it not
functional (implemented in subsequent patch).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.
Allow these devices to set this from Kconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
CLI support with the HUSH parser is not currently SPL safe due to it's
use of realloc. That function is not defined for SPLs that use
SYS_MALLOC_SIMPLE. CLI support can be built in to SPL and some functions
do work, but use of some like run_command() will cause build to fail.
When no SPL code calls this function build works as the compiler removes
this unreachable code so the unresolved symbols are ignored.
If DFU support is enabled in SPL then MMU DFU support may get brought in
also, this code does make a call to run_command() causing build to fail
if the HUSH parser is not built-in. To break this odd and unneeded
dependency chain we use CONFIG_IS_ENABLED where appropriate to prevent
calls into HUSH code from SPL. This also removes our need to pull in the
rather unrelated source file when SPL_DFU is defined.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do this by using $(SPL_) in Makefiles and CONFIG_IS_ENABLED in C code.
This ensures the files and features are only built into the right build
for which they are enabled. Using the macros to simplify this patch was
made possible by the config symbol rename done in the last patch.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
It is not possible to link the SPL image when CONFIG_GPIO is enabled
but CONFIG_SPL_GPIO is not. Use the IS_ENABLED macro instead to
correctly check whether CONFIG_{SPL_}GPIO is enabled.
This commit fixes the following errors:
* undefined reference to `dm_gpio_get_value
* undefined reference to `gpio_request_by_name'
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[trini: Move guard to fix warning in msdc_ops_get_wp()]
Signed-off-by: Tom Rini <trini@konsulko.com>
The code is checking for incomplete read when it see the INT_XFER_COMPL
flag, but it forget to first check whether there is anything left in the
FIFO to copy to the RX buffer. This means that sometimes we will get
errors because of erroneous incomplete read operation.
This commit fixes the driver re-ordering the code so that we first
check for data inside the RX fifo and only after check the status
of the INT_XFER_COMPL flag.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
As Poplar supports running TF-A with OP-TEE as BL32
payload, add op-tee node in DT, which enables usage of
OP-TEE driver (which provides an interface for requesting services
from OP-TEE).
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
It adds missing pinctrl headers, updates clock header and sync up Poplar
device tree with kernel 4.20 release.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Add pinctrl node for TLMM and add mux request for uart node.
* Rename uart to the actual board uart port.
* Fix indentendation of sdhc2 node.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The TLMM_GPIO_ENABLE bit is actually use to disable
the GPIO. change it to TLMM_GPIO_DISABLE so it's clearer.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add pinctrl driver for Dragonboard820c, currently with only
one mux func to initialize pins for serial console.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The PLL for the UART was not set, and relied on previous
initializtion made by LK. add the appropriate initialization.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The imgextract command runs a number of checks of
the specified fit. Where it checks for a load address
for compressed images the logic in the expression
is inverted as fit_image_check_comp returns 1 on
success and not 0.
Deploy u-boot-spl.stm32 binary in u-boot root folder like
the rest of the boards.
This makes it more streamlined when building in Yocto, Buildroot etc..
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
A few platforms recently added in CONFIG_DFU_MMC under include/configs
rather than via the defconfig, update them.
Signed-off-by: Tom Rini <trini@konsulko.com>
A couple of trivial fixes and improvements for ARC
Most notable are:
* Move of ENV_SIZE/ENV_OFFSET to Kconfig
* Fix with private structure allocation for arc_uart
* Definition of CONFIG_SYS_CACHELINE_SIZE useful for building drivers
Even though we don't use CONFIG_SYS_CACHELINE_SIZE in ARC-specific code
it is used a lot in different drivers for alignment purposes.
So we define it and make much more drivers at least compilable for ARC.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
"i" gets incremented before we're entering loop body
and effectively we iterate from 1 to 8 instead of 0 to 7.
This way we:
a) Skip the first line of struct hs_versions
b) Go over it and access memory beyond the structure
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
