In future Book-E implementations IVORs will most likely go away and be
replaced with fixed offsets. The IVPR will continue to exist to allow
for relocation of the interrupt vectors.
This code adds support to setup the IVORs as their fixed offset values
per the ISA 2.06 spec when we transition from u-boot to another OS
either via 'bootm' or a cpu release.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ddr_pd_cntl isn't defined in any reference manual and thus we wil
remove especially since we set it to 0, which would most likely be its
POR value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The warning is bogus, so silence it by initializing the 'ret' variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable eSDHC Clock based on generic CONFIG_FSL_ESDHC define instead of a
platform define. This will enable all the 85xx platforms to use sdhc_clk
based on CONFIG_FSL_ESDHC.
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The value of I2C_TIMEOUT in fsl_i2c.c has several problems. First, it is
defined as CONFIG_HZ/4, but it is used as a count of microseconds, so it makes
no sense to derive it from a clock rate. Second, the current value (250) is
too low for some boards, so it needs to be increased. Third, the timeout
necessary for multiple-master arbitration is larger than the timeout for basic
read/write operations, so we shouldn't have a single constant for both timeouts.
Finally, it would be nice if we could override these values on a per-board
basis.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Reset any i2c devices that may have been interrupted during a system reset.
Normally this would be accomplished by clocking the line until SCL and SDA
are released and then sending a start condtiion (From an Atmel datasheet).
There is no direct access to the i2c pins so instead create start commands
through the i2c interface. Send a start command then delay for the SDA Hold
time, repeat this by disabling/enabling the bus a total of 9 times.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Rather than maintain/extend the current ifeq($(ARCH)) mess that exists in
the standalone Makefile, push the setting up of LOAD_ADDR out to the arch
config.mk (and rename to STANDALONE_LOAD_ADDR in the process). This keeps
the common code clean and lets the arch do whatever crazy crap it wants in
its own area.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Removed stdio.h inclusion and moved trace macros to use printf avoiding to
write debug informations to standard error.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Some files included my old standerd file header which had a "All
Rights Reserved" part. As this has never been my intention, I remove
these lines to make the files compatible with GPL v.2 and later.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix warning messages:
cmd_mtdparts.c:1429: warning: format '%08lx' expects type 'long
unsigned int', but argument 6 has type 'u32'
cmd_mtdparts.c:1429: warning: format '%08lx' expects type 'long
unsigned int', but argument 7 has type 'u32'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Added a arch_preboot_os() function that cpu specific code can implement to
allow for various modifications to the state of the machine right before
we boot. This can be useful to setup register state to a specific
configuration.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that the PCI, SATA et al compile problems have been resolved, the
cludge that was applied to avoid them can be removed
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Primary intent is to resolve build errors for this board which has been
neglected for a very long time. I do not have one of these boards, so I
cannot test functionality
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
This patch is based on a patch submitted by Jean-Christophe PLAGNIOL-VILLARD
on 18th May 2008 as part of a general i386 / sc520 fixup which was never
applied
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Removed do_pinit() - now declared in cmd_pcmcia.c
Added #define CONFIG_CMD_PCMCIA around pcmcia_off() in line with other
PCMCIA drivers
signed/unsigned type fixups
Added semi-colon after default: label as required by newer gcc
The only board that appears to use this driver is the sc520_spunk which
is very old and very likely very broken anyway. I do not have one to test
whether this patch breaks anything functionaly, I have can only check
that it compiles without warning or error
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Cast first parameter to sata_cpy()
In /drivers/block/ata_piix.h, ata_id_has_lba48(), ata_id_has_lba(),
ata_id_has_dma(), ata_id_u32(), ata_id_u64() are all defined in
include/libata.h which is included in ata.h which is included by all files
which include ata_piix.h (only ata_piix.c) so these definitions are
supurflous to (and conlict with) this in libata.h. Interestingly, my
compiler complains about ata_id_u64 already being defined, but not
ata_id_u32
ata_dump_id() is defined in include/libata.h and should not be static
(maybe should even use ata_dump_id() in libata.c
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in
commit ff4e66e93c, regressed by commit 6d7f610b09)
Cast PCI_ROM_ADDRESS_MASK to u32
Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO
Change call to pci_find_class() to pci_find_devices(). This is based on a
patch submitted on 1st March 2007 (Patch that fixes the compilation errors
for sc520_cdp board) by mushtaq_k
This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be
specified in the board config file. Dummy values have been added for the
SC520 CDP board to enable compilation, but since I do not have one of these,
I do know what the values should be
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
The current implementation has the timer being started before the interrupt
handler is installed. It the interrupt occurs before the handler is
installed, the timer interrupt is never reset and the timer stops
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
The current configuration of the Environment has the redundant copy of the
environment in the Boot Flash - This was never the intent. The Environment
should instead be in the first two sectors of the first Strata Flash
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
gcc 4.3.2 optimiser creates multiple copies of inline asm (who knows why)
Remove use of global names for labels to prevent 'symbol already defined'
errors
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
This lays the groundwork to allow architectures to share a common
mem_malloc_init().
Note that the x86 implementation was not modified as it did not fit the
mold of all other architectures.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Atmel DataFlashes by default operate with pages that are slightly bigger
than normal binary sizes (i.e. many are 1056 byte pages rather than 1024
bytes). However, they also have a "power of 2" mode where the pages show
up with the normal binary size. The latter mode is required in order to
boot with a Blackfin processor, so many people wish to convert their
DataFlashes on their development systems to this mode. This standalone
application does just that.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the NAND code now uses 64bit code, make sure we enable support for
ADI Blackfin boards in printf to avoid the warning:
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output!
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
