The initial patch had typos that caused four defconfigs to miss the
symbol transition to Kconfig. CONFIG_SYS_QE_FW_ADDR and
CONFIG_SYS_FMAN_FW_ADDR are currently initialized to 0 by default
on these builds, which prevents the firmware from loading.
Add the correct symbols to these defconfigs.
Fixes: a97a071d10 ("configs: fsl: migrate FMAN/QE specific defines to Kconfig")
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make it in a same way as on the other FOXMC products, this also helps to
avoid unwanted stop caused by some terminal servers that are sending junk
on the serial line.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch: 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the EXPU1 NOR layout.
- Extending mtd partitions according defined EXPU1 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This is used by out ESW for reading u-boot build version.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This is used by out ESW for reading u-boot build version.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update for pg-wcom-ls102x designs is introduced
with patch 81fb05e.
This patch enables already added support by:
- Defining default u-boot build as bootpackage (factory) image.
- Defining u-boot update image location according to the SELI8 NOR layout.
- Extending mtd partitions according defined SELI8 NOR layout.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The Ten64 is a networking-oriented MiniITX board
using the NXP LS1088A SoC.
This patch provides the bare minimum to support
Ten64 boards under U-Boot for distroboot.
Some related drivers have not yet been submitted
and this basic support lacks some of the
opinionated defaults provided by our firmware
distribution.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The GoFlex Home board has the network chip Marvell 88E1116R.
Use uclass mvgbe and the compatible driver M88E1118R to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: use CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add to support rsa 3072 bits algorithm in tools
for image sign at host side and adds rsa 3072 bits
verification in the image binary.
Add test case in vboot for sha384 with rsa3072 algorithm testing.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is enabled for quite a few boards which don't create ACPI tables.
Tidy this up by dropping the option for some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have sadly found their way to ARM now. Allow any arch to support
generating ACPI tables.
Disable this for the tools build.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 270f8710f9 ("crc32: Add crc32 implementation using
__builtin_aarch64_crc32b") enabled the usage of ARMv8 CRC instructions
by default, for all arm64 builds. And indeed all Arm Ltd. v8 Cortex-A
cores support the instructions, and they are mandatory starting with
architecture revision v8.1, so realistically every known hardware
implementation should support them.
The Arm Fastmodel however defaults to the bare minimum ARMv8 feature set
by default, which means v8.0 without the CRC instructions, so U-Boot
hangs very early at the moment, without any output (the boot-wrapper or
TF-A printing the last visible lines).
Support for those instructions can be enabled on the model command line
by either:
-C cluster0.cpu0.enable_crc32=1 (for each core)
or by using a higher architecture revision by default:
-C cluster0.has_arm_v8-1=1 (for each cluster)
Of course any arch revision higher than v8.1 would work as well.
But for the sake of a smooth out-of-the-box experience, let's just
disable the usage of those instructions in the defconfig, to avoid
random hangs without any clues.
Reported-by: Ross Burton <ross.burton@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch configures U-Boot SPL for DHCOR SoM to permit DFU upload of
SPL and subsequent u-boot.itb for recovery or commissioning purposes.
To start U-Boot on DHCOR based board, e.g. Avenger96, proceed as follows:
- Install dfu-util on the host PC (in debian this is package 'dfu-util')
- Power off the Avenger96 board.
- Connect both USB-serial console and USB-OTG microB ports to host PC.
- Switch Avenger96 to USB boot mode -- BOOT0..2 switches all set to 0.
- Power on the Avenger96 board.
- Verify using '$ dmesg' that a new device has been detected as follows:
New USB device found, idVendor=0483, idProduct=df11, bcdDevice= 2.00
New USB device strings: Mfr=1, Product=2, SerialNumber=3
Product: DFU in HS Mode @Device ID /0x500, @Revision ID /0x0000
Manufacturer: STMicroelectronics
- Upload U-Boot SPL:
$ dfu-util -a 1 -D u-boot-spl.stm32
- Upload U-Boot proper:
$ dfu-util -a 0 -D u-boot.itb
- At this point, SPL will wait for user to press "Ctrl-C" on serial
console. When ready to interact with U-Boot, press Ctrl-C to start
the bootloader.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_AT91_EFLASH
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Eugen Hristev <eugen.hristev@microchip.com>
Use moveconfig.py script to convert define CONFIG_SYS_MAX_FLASH_BANKS
and CONFIG_SYS_MAX_FLASH_BANKS_DETECT to Kconfig and move these entries
to defconfigs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Re-switch to IS_ENABLED check in spi-nor-core.c, re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Falcon mode is very useful in improving boot speed. A question that
Falcon mode asks is "Where do I look for the kernel". With MMC boot
media, the correct answer is CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR.
The scope of this patch is to move this to Kconfig.
It is possible for a system to support Falcon mode from NOR but not
MMC. In that case, mmc_load_image_raw_os() would not be used. To
address this, conditionally compile mmc_load_image_raw_os() when
SPL_FALCON_BOOT_MMCSD, instead of SPL_OS_BOOT.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move spl_start_uboot to its own guard in spl_mmc.c, rerun migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
After next branch was merged to v2022.01 release, U-Boot on A3720 started
printing "<debug_uart>" line on UART during booting. There is no need to
print this debug line by default, so disable it via config option
CONFIG_DEBUG_UART_ANNOUNCE in all config files for Armada 3720 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
On of the MiniPCIe ports on Turris Omnia is also a mSATA port. Whether
it works in SATA or PCIe mode is determined by a strapping pin, which
value is read from the MCU.
We already determine which type of card is connected when configuring
SerDeses.
But until now we left both SATA and PCIe port 0 nodes in device tree
enabled, and so the SATA driver is probed in U-Boot / Linux even if we
know there is no mSATA card, and similarly PCIe driver tries to link on
port 0 even if we know there is mSATA card, not a PCIe card.
Fixup device tree blob to disable SATA node if mSATA card is not
present, and to disable PCIe port 0 node if mSATA card is present.
Do this for U-Boot's DT blob before relocation and also for kernel DT
blob before booting.
This ensures that software does not try to use SATA or PCIe HW when
corresponding PHY is not configured.
Signed-off-by: Pali Rohár <pali@kernel.org>
[ refactored and fixed some issues ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The Khadas vim3 and vim3l defconfigs introduced with:
* f89b90d2d9 ("configs: add khadas-vim3{l}_android for AOSP support")
* 425f06f86e ("configs: prepare khadas-vim3{l}_ab_android for AOSP support")
were based on an outdated defconfig prior to the ede1f4f297 ("configs:
amlogic: Disable CONFIG_NET_RANDOM_ETHADDR when unnecessary") cleanup.
Disable CONFIG_NET_RANDOM_ETHADDR for the android configs as well to
stay consistent.
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220112084023.2858375-1-mkorpershoek@baylibre.com
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
CONFIG_PHANDLE_CHECK_SEQ will allow different sequence number for nodes
that have the same name, but they are different.
In sama7g5ek case, there are multiple 'i2c@600' nodes which are child
nodes of different parent 'flexcom' nodes.
These are different i2c busses even if the node is the same, and have to be
differentiated.
Without this config, the sequence number 0 is reused for two i2c busses, and
this is something that we have to avoid:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
Looking for 'i2c' at 6236, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
After this patch:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
- i2c1, /ahb/apb/flexcom@e2818000/i2c@600
Found seq 1
Before the patch:
=> i2c bus
Bus 0: i2c@600
Bus 0: i2c@600 (active 0)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
=>
After the patch:
=> i2c bus
Bus 0: i2c@600
Bus 1: i2c@600 (active 1)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Memory layout in the comment is from Armada XP platform which uses load
address 0x40004030. DB-88f6720 is Armada 375 platform which uses same load
address as Armada 38x which is 0x40000030.
Currently SPL support for Armada 375 is unfinished and does not work. There
is missing Serdes initialization and DDR3 training code. So nobody noticed
that CONFIG_SPL_* options are not correct.
Fix at least CONFIG_SPL_TEXT_BASE constant and remove incorrect comments
about memory layout. So it is not misleading.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Add MVEBU PCIe configs
- Also add SYS_THUMB_BUILD to keep u-boot image size within 512K
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The only user of board_pex_config() weak function is A385 controlcenterdc
board. It looks like that code in its board_pex_config() function needs to
be executed after PCIe link is up. Therefore put this code into
spl_board_init() function which is called after a38x serdes initialization,
and therefore it is after the serdes hws_pex_config() function finishes
(which is the state before this change).
With this change completely remove board_pex_config() function as it is not
used anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
Since commit f7ac30b042, the pin muxing for mmc was removed from the
board file to be managed by DM_MMC which requires PINCTRL to work. It
made the change for sabrelite but nitrogen configs were forgotten.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Increase CONFIG_ENV_OFFSET to avoid the environment region to
overlap with U-Boot proper.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
After the conversion to DM the SD card shows up as 'mmc 2'
device.
Adjust the 'mmcdev' and the distro command 'func' accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Use binman to pack images.
Note that imx8mm_venice supports several boards via multiple DTB's thus
in the fit node we must use:
- fit,fdt-list = "of-list"
- fdt-SEQ
- config-SEQ
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The standard 1GB Nano was converted to binman, but the 2G version
was neglected. Convert it to binman as well.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
