At SPL stage when stack is relocated, the stack pointer needs to be
updated, the stack pointer may point to stack in on chip memory even
though stack is relocated.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
During compilation splash_source puts out below warning for type
conversion in splash_load_fit for bmp_load_addr and fit_header.
Change their type to uintptr_t to fix the warnings.
common/splash_source.c: In function ‘splash_load_fit’:
common/splash_source.c:366:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
366 | img_header = (struct legacy_img_hdr *)bmp_load_addr;
| ^
common/splash_source.c:376:49: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
376 | res = splash_storage_read_raw(location, (u32)fit_header, fit_size);
| ^
common/splash_source.c:401:25: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
401 | memmove((void *)bmp_load_addr, internal_splash_data, internal_splash_size);
The above warnings are generated if CONFIG_FIT is enabled.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
This enables implementing custom logic after a bitstream was loaded
into the fpga.
Signed-off-by: Christian Taedcke <christian.taedcke@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Link: https://lore.kernel.org/r/20230720072724.11516-1-christian.taedcke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Some devices keep 2 copies of the bootloader_message in the misc
partition and write each in sequence when updating. This ensures that
there is always one valid copy of the bootloader_message. Teach u-boot
to optionally try a backup bootloader_message from a specified offset if
the primary one fails its CRC check.
Signed-off-by: Joshua Watt <JPEWhacker@gmail.com>
The output is garbled when tiny printf() is used. Correct this by adding
a special case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When video is set up in SPL, U-Boot proper needs to use the correct
parameters so it can write to the display.
Put these in a bloblist so they are available to U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to see the base of the malloc region. This is visible when
debugging but not in normal usage.
Add it to the global data so that it can be shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
At present this leaves the stack at the pre-relocation value. This is not
ideal since we want to have U-Boot running entirely from the top of
memory.
In addition, the new global_data pointer is not actually used, since
the global_data pointer itself is relocated, then the pre-relocation value
is changed, so the effective value (after relocation) does not update.
Adjust the implementation to follow the 32-bit code more closely, with a
trampoline function which is passed the new stack and global_data pointer.
This ensures that the correct values come through even when relocating.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a bit more detail so it is clear that multiple devices are
supported, but only one per driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In case of OF_SEPARATE (!OF_EMBED), the devicetree blob is placed
after _end, and fdt_find_separate() always returns _end. There is
a .bss section after _end and the section is cleared before relocation.
When GD_FLG_SKIP_RELOC is set, relocation is skipped, so the blob is
still in .bss section, but will be cleared. As a result, the devicetree
become invalid.
To avoid this issue, should relocate it regardless of GD_FLG_SKIP_RELOC
in reloc_fdt().
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
memalign() returns a pointer which is to be freed by free(). To call
unmap_sysmem() is incorrect, furthermore it was called in a wrong scope.
Also add a check for allocation error.
Fixes: d7af2baa49 ("crypto/fsl: Fix HW accelerated hash commands")
Cc: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This feature is different enough from bootstd that it probably deserves
its own log category. It cannot use a uclass since it is not a device.
Add a new category.
Signed-off-by: Simon Glass <sjg@chromium.org>
As implemented in the arch/arm/mach-rockchip/tpl.c file,
the CONFIG_TPL_BANNER_PRINT option will not work
if either of these options is not enabled.
Add dependency constraints to the CONFIG_TPL_BANNER_PRINT option
definition to prevent configuration problems
where option is enabled but do not take effect.
Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
CONFIG_SYS_CONSOLE_ENV_OVERWRITE is implemented in common/console.c
when "#if CONFIG_IS_ENABLED(SYS_CONSOLE_IS_IN_ENV)" is met.
It is recommended to add dependency constraints to its definition.
Suggested-by: Yanjie Ren <renyanjie01@gmail.com>
Signed-off-by: Ying Sun <sunying@nj.iscas.ac.cn>
Describe which numeric values can be used for as scratch options for
OpenSBI.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, spl_end points to the __bss_end address, which
is an external RAM address instead of the end of the SPL text
section in the internal RAM.
This causes boot failures on imx6-colibri, for example:
```
Trying to boot from MMC1
SPL: Image overlaps SPL
resetting ...
```
Fix this problem by assigning spl_end to _image_binary_end, as this
symbol properly represents the end of the SPL text section.
From u-boot-spl.map:
.end
*(.__end)
0x00000000009121a4 _image_binary_end = .
Fixes: 77aed22b48 ("spl: spl_legacy: Add extra address checks")
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # DH i.MX6Q DHCOM PDK2
The current mechanism is unnecessarily complex. Simplify the whole mechanism
such that the entire fitImage is signed, IVT is placed at the end, followed
by CSF, and this entire bundle is also authenticated. This makes the signing
scripting far simpler.
Signed-off-by: Marek Vasut <marex@denx.de>
The intent here was to allow ANSI codes to be disabled, since it was
proving impoosible to test operation of the menu code when it kept moving
the cursor. Unfortunately this ended up in the patch.
Correct this by enabling ANSI again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Pali Rohár <pali@kernel.org>
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Fixes: 32bab0eae5 ("menu: Make use of CLI character processing")
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Ensure that every write is flushed to memory and afterward reads are
from memory.
Since the algorithm rely on the fact that accessing to not existent
memory lead to write at addr / 2 without this modification accesses
to aliased (not physically present) addresses are cached and
wrong size is returned.
This was discovered while working on a TI AM625 based board
where cache is normally enabled, see commit c02712a748 ("arm: mach-k3: Enable dcache in SPL").
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
If only FIT images are enabled and loading the FIT image fails,
spl_nor_load_image() should return an error instead of zero.
Without this patch:
>>SPL: board_init_r()
spl_init
Trying to boot from NOR
Unsupported OS image.. Jumping nevertheless..
image entry point: 0x0
With patch:
>>SPL: board_init_r()
spl_init
Trying to boot from NOR
SPL: failed to boot from all boot devices (err=-6)
.### ERROR ### Please RESET the board ###
Signed-off-by: Mario Kicherer <dev@kicherer.org>
Add support to load the next stage image from an NVMe disk which may
be formatted as an EXT or FAT filesystem.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
[trini: Drop hunk changing disk/part.c as that breaks other users]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a generic API to support loading of SPL payload from any supported
filesystem on a given partition of a block device.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Add kconfig options to enable NVME and PCI NVMe support in SPL
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new function fdt_copy_fixed_partitions to copy the fixed
partition nodes from U-Boot device tree to Linux kernel
device tree and to dynamically configure the MTD partitions.
This function fdt_copy_fixed_partitions is only based on device tree
with livetree compatible function and replace the function
fdt_fixup_mtdparts based on mtdparts variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch is a preliminary patch to use ofnode function
is fdt_support to read the U-Boot device tree with livetree
compatible functions.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 9905cae65e ("fs: ext4: check the minimal partition size
to mount"), a valid size needs to be provided when mounting
an ext filesystem. Fix the spl ext driver to use the parition size
instead of 0 when mounting the filesystem.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Invoking the sandbox with
/u-boot -c ⧵0xef⧵0xbf⧵0xbd
results in a segmentation fault.
Function b_getch() retrieves a character from the input stream. This
character may be > 0x7f. If type char is signed, static_get() will
return a negative number and in parse_stream() we will use that
negative number as an index for array map[] resulting in a buffer
overflow.
Reported-by: Harry Lockyer <harry_lockyer@tutanota.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Per the fit_conf_get_node() API doc, it returns configuration node
offset when found (>=0).
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_STORAGE and matching SYS_USB_FAT_BOOT_PARTITION .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_HOST and updates help text of both USB_HOST
and SPL_USB_HOST .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add method to remove video driver before loading u-boot proper. When
bootstage changes from SPL to u-boot proper, noo method is called to
remove video driver, and at u-boot proper if video driver is not
enabled, the video driver starts displaying garbage on the screen,
because there is no reserved space for video and the frame buffer gets
u-boot proper data written.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Fix comments error in EVENT_DEBUG description:
this get usefui -> this to get useful
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The u-boot hush shell doesn’t support the unset command to clear a
variable and therefore an empty value ("c=") should be a valid value
for the set_local_var function to clear the variable. This partial
reverts commit aa72252963 ("common: cli_hush: avoid dead code") and
only checks for a `=` in the string. Additionally explicit call the
unset_local_var function to remove the variable if the value is empty.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function fdt_simplefb_enable_existing_node() should be static as it is not
used outside common/fdt_simplefb.c.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Avoid using preprocessor compilation directives and instead use simple
logical expressions for better readability since compiler will anyway
optimize out the respective code block if condition is not satisfied.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
To support splash screen at both u-boot proper and SPL use
CONFIG_IS_ENABLED and CONFIG_VAL to check for video related Kconfigs at
respective stages.
Replace CONFIG_CMD_BMP with CONFIG_BMP to enable splash_display function
at u-boot proper and SPL.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
