The current capsule authentication code checks if the environment
variable capsule_authentication_enabled is set, for authenticating the
capsule. This is in addition to the check for the config symbol
CONFIG_EFI_CAPSULE_AUTHENTICATE. Remove the check for the environment
variable. The capsule will now be authenticated if the config symbol
is set.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch adds the base support for the Marvell Octeon TX2 CN913x DB.
Only one defconfig is added with this patch. Other board variants are
available (NAND, MMC booting) and images for these boards can be
generated by following the documentation added in the included README.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is more consistent with the naming of other ram banks, and matches
what Linux is doing.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
We just need to initialize all the clocks pre-reloc. The clock driver
creates a bunch of devices, so we need to increase the pre-reloc malloc
arena.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Update the Kconfig and the board file to make the am335x board compatible
with cape detection.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
The am335x from BeagleBone use i2c EEPROM to detect capes.
The memory is wired to i2c bus 2 therefore it need to be enabled.
Add i2c2 clock, pinmux description and pinmux enable function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Add the extension_board_scan specific function to scan the information
of the EEPROM on one-wire and fill the extension struct.
Add the Kconfig symbol to enable the needs to detect DIPs.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Andre Przywara <andre.przywara@arm.com>
The BeagleBone platforms all use a common mechanism to discover and
identify extension boards (called "capes"): each extension board has an
I2C-connected EEPROM describing itself.
This patch implements a generic extension_scan_board() feature that can
be used by all BeagleBone platforms to read those I2C EEPROMs and fill
in the list of "extension" structures.
Following commits will enable this common logic on two BeagleBone
platforms.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
This commit extends the sandbox to implement a dummy
extension_board_scan() function and enables the extension command in
the sandbox configuration. It then adds a test that checks the proper
functionality of the extension command by applying two Device Tree
overlays to the sandbox Device Tree.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
[trini: Limit to running on sandbox]
Signed-off-by: Tom Rini <trini@konsulko.com>
Scrub duplicate /memory@* node entries here. Some R-Car DTs might
contain multiple /memory@* nodes, however fdt_fixup_memory_banks()
either generates single /memory node or updates the first /memory
node. Any remaining memory nodes are thus potential duplicates.
However, it is not possible to delete all the memory nodes right
away, since some of those might not be DRAM memory nodes, but some
sort of other memory. Thus, delete only the memory nodes which are
in the R-Car3 DBSC ranges.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The rcar-common/common.c contains various common board functions shared
by all R-Car and RZG boards. This board is not compiling the file in, so
add it. This way, part of the board code can be de-duplicated too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Parse MAC addresses from EEPROM and set them in the env. This is needed
to get MAC address for additional ethernet ports on the EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Create a new CONFIG_K3_DDRSS option to select the common parts of the
k3-ddrss driver. Also introduce a choice that depends on the top level
option to select CONFIG_K3_J721E_DDRSS for j721e support, and update
corresponding Kconfig as required.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
These specific configs are missing a number of migrations. In addition,
they are blocking completion of the now-expired DM_MMC migration as it
requires enabling BLK.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Supported peripherals: Ethernet, eMMC, Serial.
U-Boot SPL 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14
+0200)
Normal Boot
Trying to boot from MMC2
U-Boot 2021.04-00911-g5fa1e2ffeb-dirty (Apr 23 2021 - 09:11:14 +0200)
CPU: Freescale i.MX8MQ rev2.1 at 1000 MHz
Reset cause: POR
Model: Ronetix iMX8M-CM SoM
DRAM: 1 GiB
WDT: Started with servicing (60s timeout)
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet@30be0000 (eth0) using random MAC address -
42:0d:e7:78:da:53
eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
u-boot=>
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Current setup instructions for i.MX8QM MEK board include somewhat
conflicting instructions, so here's an attempt to fix it.
After trying both sets of firmwares, I can conclude that both of
them fail to work:
- no boot at all with imx-sc-firmware-0.7 / firmware-imx-7.6
- partial success with imx-sc-firmware-1.1 / firmware-imx-8.0:
U-Boot 2021.04-rc3-00135-ge0669a43c8 (Mar 08 2021 - 16:49:08 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
mu_hal_receivemsg timeout
Build: SCFW 65afe5f6, SECO-FW 65afe5f6, ATF a-20190
mu_hal_receivemsg timeout
sc_misc_get_boot_dev: res:16
Boot: SD0
DRAM: mu_hal_sendmsg timeout
sc_rm_is_memreg_owned: mr:0 res:21
...
Signed-off-by: Priit Laes <priit.laes@paf.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Carrier board for
creating complete i.Core MX8M Mini C.TOUCH 2.0 board.
Linux dts commit details:
commit <a142252061ff> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
C.TOUCH 2.0")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core MX8M Mini is an EDIMM SoM based on NXP i.MX8M Mini from Engicam.
i.Core MX8M Mini needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Mini EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <051c08eea682> ("arm64: dts: imx8mm: Add Engicam i.Core MX8M Mini
EDIMM2.2 Starter Kit")
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The DA9063 enables the CRYSTAL bit by default, but there is no
crystal populated on the BA16 system on module. Without explicitly
clearing the CRYSTAL bit the system runs unstable and sometimes
reboots unexpectedly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds the base support for the Marvell Octeon TX2 CN9130 CRB.
Not all interfaces are supported fully yet.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the board specific QLM/DLM init code to the Octeon 3
EBB7304 board. The configuration of each port is read from the
environment exactly as done in the 2013 U-Boot version to keep the
board and it's configuration compatible.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently u-boot supports addresses upto 39-bits only. If anybody
wants to use addresses of more than 39-bits in Linux they will have
a separate memory node in DT. In such cases they will have multiple
memory nodes.
Currently u-boot selects and runs on lower memory bank region.
But bootscript is being loaded on dram bank 0, where dram bank 0 will
point to 1st memory node in DT. If first memory node is mentioned as
higher ddr(>39-bits address) then u-boot cannot load the bootscript.
So fix this issue by setting bootscript address within the lower memory
bank region.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change "dfu_usb" to "usb_dfu" for better representation and change
required macros. Add 60s timeout of dfu-utils to start transaction.
Add support for usb thor to distro boot. Remove DFU_ALT_INFO_RAM
as we use bootcmd_usb_dfu instead of dfu_ram.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In usb boot mode distro boot should select usb device as primary boot
device instead of usb host. So make usb dfu as primary boot device. But do
not list it in boot_targets as fallback option because it is not classic
mode for booting. Using 60s timeout by default should be enough time for
dfu-utils to start transaction. In case none needs this please change
timeout value in the command or disable CONFIG_DFU_TIMEOUT.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable saving variables to MMC(FAT) and SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Enable ENV_FAT_DEVICE_AND_PART="0:auto" for Versal platforms as well.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable saving variables to MMC(FAT), NAND, SPI based on primary
bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE).
Since most of the flashes on zynq evaluation boards are 16MB in size,
set default ENV_OFFSET to 15MB(0xE00000).
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-boot might display wrong module revision information
for modules with an assembly version 'K'. "cfgblock create"
does not takes into account all revision digits from PID8.
This fix takes into account all digits of PID8
to store module revision.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Rob does not have access to any Calxeda systems anymore, also has
expressed a lack of interest in those systems in the past.
I have multiple working Midway nodes under my desk in the office, so
am happy to take over maintainership.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).
Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.
Also, to cover the whole of memory, we need to enable PHYS_64BIT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
