This patch adds intermediate kconfig symbols which select their SoC
family. Boards then select them instead of the family symbol directly.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.
Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enables DM_USB on the Marvell AXP / A38x eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enabled the MVEBU PCIe support on the db-88f6820-gp A38x
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada
XP / 38x boards in mainline U-Boot. This is done in preparation for
the ECC SDRAM scrubbing that needs to be done in the main U-Boot.
The SPL (previously bin_hdr) has already scrubbed the area:
0x0000.0000 - 0x0100.0000
In this area this main U-Boot needs to get loaded. The main U-Boot
then can scrub the remaining SDRAM area while running from this
location.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds the configuration options to boot via SDIO/MMC on the
Marvell DB-88F6820-GP Armada A38x board. The default boot device
is still SPI NOR flash.
To enable MMC booting on this board 2 things need to be changes:
a) Change kwbimage.cfg
BOOT_FROM sdio
b) In the config header select
#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD
The generated image needs to be copied to the first bootable MMC
partition:
dd if=u-boot-spl.kwb of=/dev/sdX1
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
This patch adds SPL support for the Marvell DB-88F6820-GP board.
With this change, the bin_hdr from the original Marvell U-boot
is not needed any more on this board. The sources from bin_hdr
(SERDES/PHY and DDR setup) are now integrated in mainline
U-Boot. And this patch enables them for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enabled the USB/EHCI support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Configure and enable the SATA/SCSI (AHCI) support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board
configuration. Including support for the common partitions and
filesystems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it. Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds support for the Marvell DB-88F6820-GP Armada A38x
evaluation board.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Please note that this board support right now only supports the
main U-Boot. Without the bin_hdr integration (DDR training etc). This
will be added in a few days / weeks to complete this board port. But
till then this U-Boot version can be run on the target via the
original Marvell U-Boot via this command:
tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
