The push / pop instructions used in this file are available only with
more recent tool chains:
cache.S: Assembler messages:
cache.S:133: Error: bad instruction `push {r0,r1,r2,lr}'
cache.S:160: Error: bad instruction `pop {r1,r2,r3,pc}'
cache.S:164: Error: bad instruction `push {r0,r1,r2,lr}'
cache.S:191: Error: bad instruction `pop {r1,r2,r3,pc}'
Change push/pop into stmfd/ldmfd instructions to support older
versions of binutils as well.
I verified that the modified source code generates exactly the same
binary code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rix <tom@bumblecow.com>
Conflicts:
CONFLICT (rename/add): Rename
board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile
in 89b765c7f6.
board/ti/tnetv107xevm/Makefile added in HEAD
But files were identical, so no problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the Marvell Orion5x SoC.
It has no use alone, and must be followed by a patch
to add Orion5x support for serial, then support for
the ED Mini V2, an Orion5x-based product from LaCie.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Part of this patch is by: Mikhail Kshevetskiy.
Stack must be aligned to 8 bytes on PXA (possibly all armv5te) for LDRD/STRD
instructions. In case LDRD/STRD is issued on an unaligned address, the behaviour
is undefined.
The issue was observed when working with the NAND code, which was rendered
disfunctional. Also, the vsprintf() function had serious problems with printing
64bit wide long longs. After aligning the stack, this wrong behaviour is no
longer present.
Tested on:
Marvell Littleton PXA310 board
Toradex Colibri PXA320 board
Aeronix Zipit Z2 PXA270 handheld
Voipac PXA270 board
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
initialized for CS1
From: Vaibhav Hiremath <hvaibhav@ti.com>
The patch makes sure that size for SDRC CS1 gets calculated
only when the CS1 SDRC is initialized.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This is an initial commit with
basic functionality, more commits with drivers, etc. to follow.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
initialized for CS1
From: Vaibhav Hiremath <hvaibhav@ti.com>
The patch makes sure that size for SDRC CS1 gets calculated
only when the CS1 SDRC is initialized.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This is an initial commit with
basic functionality, more commits with drivers, etc. to follow.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The ARM1136 cache_flush() function uses the "mcr p15, 0, rn, c7, c7, 0"
instruction which means "Invalidate Both Caches" when in fact the intent
is to clean and invalidate all caches. So add an "mcr p15, 0, %0, c7,
c10, 0" instruction to "Clean Entire Data Cache" prior to the "Invalidate
Both Caches" instruction to insure that memory is consistent with any
dirty cache lines.
Also fix a couple of "flush v*" comments in ARM1136 cpu_init_crit() so
that they correctly describe the actual ARM1136 CP15 C7 Cache Operations
used.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Fix the following compiler problems:
arch/arm/cpu/arm920t/a320/liba320.a(timer.o): In function `udelay':
/home/wd/git/u-boot/work/arch/arm/cpu/arm920t/a320/timer.c:160: multiple definition of `udelay'
lib/libgeneric.a(time.o):/home/wd/git/u-boot/work/lib/time.c:34: first defined here
lib/libgeneric.a(time.o): In function `udelay':
time.c:(.text+0x1c): undefined reference to `__udelay'
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix MX51 CPU detect message.
Original string was:
CPU: Freescale i.MX51 family 3.0V at 800 MHz
which can be misinterpreted as 3.0 Volts instead of the silicon revision.
,change it to:
CPU: Freescale i.MX51 family rev3.0 at 800 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The QONG module can be downsized and delivered
with 128MB instead of 256MB. The patch adds
run time support for the two different memory
configurations.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Replace call to imx_get_mpllclk with imx_get_armclk
to show frequency of ARM core instead of mpll internal
bus in print_cpuinfo.
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
The lowlevel_init file contained some hard-coded values
to setup the RAM. These board related values are moved into
the board configuration file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Because of s5pc1xx gpio is same as s5p seires SoC,
move gpio functions to drvier/gpio/
and modify structure's name from s5pc1xx_ to s5p_.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This helps to clean up the include/ directory so that it only contains
non-architecture-specific headers and also matches Linux's directory
layout which many U-Boot developers are already familiar with.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk
This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
