The interrupt collector macro name for i.MX23 is MXS_ICOLL_BASE,
this is correct and matches the documentation of both i.MX23 and
i.MX28. Align the i.MX28 macro accordingly. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Sync the devicetree files used in the kernel for the imx8mm-phyboard-polis
with the corresponding devicetree files in U-Boot.
Replaced phycore-imx8mm.dts with kernel dts imx8mm-phyboard-polis-rdk.dts
Synced with kernel 6.5.0-rc1 commit
e752a4f9589c (arm64: dts: freescale: imx8mm-phyboard: Add I2C4 pinmuxing)
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Commit 0aea5dda29 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Currently, building imx8qm_dmsse20a1_defconfig leads to the following
warning:
aarch64-linux-ld.bfd: invalid origin for memory region .sdram
Fix it by using the same SPL memory layout as done in the imx8mq_evk.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Function ddr_load_train_firmware() is called 4 times in a loop by
ddr_cfg_phy(). The first 3 calls are all '1D' type and just loading the
same FWs. Let's add a type check and save 2 of them. This helps to
reduce DDRPHY training time from 269 ms down to 212 ms, and thus speed
up boot time ~ 50 ms.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The commit in linux kernel 81186dc16101 ("dt-bindings: zynqmp: add
destination mailbox compatible") make compatible string for child nodes
mandatory that's why add it.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-5-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As of now only one mailbox agent is supported by mailbox driver.
On zynqmp platform there are about 7 mailbox agents which can communicate
over same IPI channel to U-Boot. This patch series introduces new
"zynqmp_ipi_dest" driver which adds one to multi-channel mailbox
support.
Following format in device-tree is expected as per latest bindings:
zynqmp-ipi {
compatible = "xlnx,zynqmp-ipi-mailbox";
mbox_1: mailbox@1 {
/* New compatible for child node */
compatible = "xlnx,zynqmp-ipi-dest-mailbox";
...
};
...
mbox_n: mailbox@n {
compatible = "xlnx,zynqmp-ipi-dest-mailbox";
...
}
};
Then mailbox client uses child mailbox node as following:
ipi-dest-1 {
...
mboxes = <mbox_1 0>, <mbox_1 1>;
mbox-names = "tx", "rx";
...
};
New "zynqmp_ipi_dest" driver is for devices with
"xlnx,zynqmp-ipi-dest-mailbox" compatible string. This driver will take care
of mailbox send recv ops and it replaces previous "zynqmp_ipi" driver.
Now "zynqmp_ipi" driver simply binds each child device with "zynqmp_ipi_dest"
driver.
However, its important to maintain backward comaptibility with previous
bindings where child node does not have compatible string. In such case, new
driver isn't probed by U-Boot during boot and system fails to boot. To
resolve this issue firmware-zynqmp.c driver probes all the IPI parent node
driver which binds each child node device with "zynqmp_ipi_dest" driver.
This makes sure corresponding child driver will be
probed when requested using mbox_get_by_name or mbox_get_by_idx
framework calls.
This way multiple mailbox agents are supported in device-tree without breaking
previous binding support.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-4-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
If U-Boot is running in Exception Level 3 then use hardcode
register values for mailbox message passing with PMU.
This is only supported for zynqmp platform.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-3-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use SMC calls to TF-A to operate IPI for execution level below 3. For
EL3 use hardcode IPI registers as TF-A isn't available in EL3.
Hence, in EL3 remote and local IPI ids retrieved using xlnx,ipi-id
property are unused.
Signed-off-by: Tanmay Shah <tanmay.shah@amd.com>
Link: https://lore.kernel.org/r/20231204215620.63334-2-tanmay.shah@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
In case of A/B update systems there should be an option to load the same
binary/binaries to different location and they should work.
Before this patch boot.bin with U-Boot SPL can be added to whatever 32k
offset in SPI and SPL finds u-boot.itb at CONFIG_SYS_SPI_U_BOOT_OFFS
offset. In case of A/B update systems that means that SPL is at different
locations but it still points to the same u-boot.itb which is not correct.
That's why include multiboot value to offset calculation to be able to
point to image from the same base.
It doesn't affect any current system which starts from 0 offset.
This patch also change Kria defconfig which uses A/B setup. Partition
A starts at multiboot 64, partition B at multiboot 496.
And also print message about used SPI offset which is useful for all cases.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/93903a53ad9358ae69991558b787f574797effbe.1699619666.git.michal.simek@amd.com
Add the xfer callback which is used by the MMC_SPI driver and generally by
the dm_spi_xfer callback.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Tested-by: Love Kumar <love.kumar@amd.com>
Link: https://lore.kernel.org/r/20231116164336.140171-3-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Modify start_transfer and related functions to take a udevice parameter
as input instead of spi_slave. This is needed so that start_transfer can
be used directly via the xfer callback. Also fix a compiler warning.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Tested-by: Love Kumar <love.kumar@amd.com>
Link: https://lore.kernel.org/r/20231116164336.140171-2-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The host bridge MMIO region is disabled by default due to which MMIO
accesses cause an exception. Fix it by setting the bridge enable bit.
This change is ported from the linux pcie-xilinx driver.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231116165103.140968-3-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
As per the xlnx,axi-ethernet-1.00.a DT documentation in linux, the AXI
DMA registers can be obtained via the reg property or via a separate
node for the axistream DMA controller. Currently only the latter is
supported, so add support to fetch the DMA controller registers from the
"reg" property.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20231116164024.139934-1-mchitale@ventanamicro.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable the initial kria SOM specific configurations like pinctrl,
pinconf etc. Also add the environment file.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20231109042407.6123-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Systems without getopt support fall back to plain full bdinfo print,
handle such a case, which occurs e.g. with sandbox_flattree_defconfig .
Fixes: 8827a38714 ("test: bdinfo: Test bdinfo -h")
Fixes: 2696f3ab81 ("test: bdinfo: Test bdinfo -m")
Fixes: 3ff2d796a6 ("test: bdinfo: Test bdinfo -e")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Recently pylint has started to complain about:
No name 'fs_helper' in module 'tests' (no-name-in-module)
Due to:
from tests import fs_helper
However, we have:
test/py/tests/fs_helper.py
And since we do not want to add a dummy test/py/tests/__init__.py to
silence this warning we instead just disable it as needed.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The bdinfo -e should print only the board ethernet settings.
Test the expected output.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The bdinfo -m should print only the board memory layout.
Test the expected output.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The bdinfo -h should print error message that -h is an unknown
parameter and then command help text. Test the expected output.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Factor out the core of test for all bdinfo output into bdinfo_test_all()
and then reuse it to verify that both 'bdinfo' and 'bdinfo -a' print all
the bdinfo output.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename bdinfo_test_move() to bdinfo_test_full(). The former is a
remnant of deriving this test from another test. No functional
change.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Enable GETOPT so that 'bdinfo' command with getopt() support can be
tested in CI.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for printing ethernet settings only via 'bdinfo -e' .
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for printing memory layout only via 'bdinfo -m' .
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add optional support for getopt() and in case this is enabled via
GETOPT configuration option, implement support for 'bdinfo -a'.
The 'bdinfo -a' behaves exactly like bdinfo and prints 'all' the
bdinfo information. This is implemented in preparation for other
more fine-grained options.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
We currently use an outdated format 32-bit format for SMBIOS tables.
So we must allocate SMBIOS tables below 4 GiB.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The wdt_start function takes timeout_ms as a parameter and starts the
watchdog with this value. However, when you output the message, it shows
the default timeout value for the watchdog device.
So this patch fixes that part to output the correct timeout value.
Before -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (60s timeout)
After -->
StarFive # wdt start 3000
WDT: Started watchdog@13070000 without servicing (3s timeout)
Fixes: c2fd0ca1a8 ("watchdog: Integrate watchdog triggering into the cyclic framework")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Compiling with CONFIG_USB_XHCI_PCI and CONFIG_PCI=n results in
usb/host/xhci-pci.c:48:(.text.xhci_pci_probe+0x44):
undefined reference to `dm_pci_write_config32
Add the missing Kconfig dependency.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Like Rockchip RK3328 and RK3568, the RK3588 also have a single node to
represent the glue and ctrl for USB 3.0.
Use rk_ops as driver data to select correct ctrl node for RK3588 DWC3.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
USB UFI uses fixed 12-byte commands (as does RBC, which is not
supported), but SCSI does not have this limitation. Use the correct
command block lengths depending on the subclass.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Some devices like YubiKeys need more time before SET_ADDRESS. The spec
says we need to wait 10ms.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
We need to get the DMA address before incrementing the pointer, as that
might move us onto another segment.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
Now that we always check the return value, just return NULL on timeouts.
We can still log the error since this is a problem, but it's not reason
to panic.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
