At present bootstage only supports U-Boot proper. But SPL can also consume
boot time so it is useful to have the record start there.
Add bootstage support to SPL. Also support stashing the timing information
when SPL finishes so that it can be picked up and reported by U-Boot
proper. This provides a full boot time record, excluding only the time
taken by the boot ROM.
Signed-off-by: Simon Glass <sjg@chromium.org>
ATF(ARM Trusted Firmware) is used by ARM arch64 SoCs, find more infomation
about ATF at: https://github.com/ARM-software/arm-trusted-firmware
SPL is considered as BL2 in ATF terminology, it needs to load other parts
of ATF binary like BL31, BL32, SCP-BL30, and BL33(U-Boot). And needs to
prepare the parameter for BL31 which including entry and image information
for all other images. Then the SPL handle PC to BL31 with the parameter,
the BL31 will do the rest of work and at last get into U-Boot(BL33).
This patch needs work with patches from Andre for SPL support multi
binary in FIT.
The entry point of bl31 and bl33 are still using hard code because we
still can not get them from the FIT image information.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
In single stage bootmode or falcon boot mode, the SPL shall update the
device tree that we load with the normal fixups done via
arch_fixup_fdt(), when possible (ie we have enough information in this
restricted environment to be able to do that still). This will include
for example updating them memory nodes.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
[trini: Reword commit message]
Move the assignment of board info to global data a bit early which is
safe,
so that ram details can be used to enable caches.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay
in thumb mode.
Similar commit:
f99993c108
Author: Matt Porter <mporter@konsulko.com>
Date: Tue May 5 15:00:23 2015 -0400
common/cmd_boot: keep ARM v7M in thumb mode during do_go_exec()
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Calls to IS_ENABLED() on a non-y/n option will always be false, even
when set. We can correct this by adding a new bool value that is set
based on the conditions required for SPL_STACK_R_MALLOC_SIMPLE_LEN to be
set instead.
Fixes: 340f418acd ("spl: Add spl_early_init()")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Changes in v2:
- Fix thinko pointed out by Lokesh
Add a Kconfig option that enables Legacy image support, this allows
boards to explicitly disable this, for instance when needed for
security reasons.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_SPL_ABORT_ON_RAW_IMAGE causes SPL to abort and move on when it
encounters RAW images, express this same functionality as a positive
option enabling support for RAW images: CONFIG_SPL_RAW_IMAGE_SUPPORT
Also move uses of this to defconfigs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Rework Kconfig logic a little, move to common/spl/Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
At present malloc_base/_limit/_ptr are not initialised in spl_init() when
we call spl_init() in board_init_f(). This is due to a recent change aimed
at avoiding overwriting the malloc area set up on some boards by
spl_relocate_stack_gd().
However if CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is not defined, we now
skip setting up the memory area in spl_init() which is obviously wrong.
To fix this, add a new function spl_early_init() which can be called in
board_init_f().
Fixes: b3d2861e (spl: Remove overwrite of relocated malloc limit)
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Rewrote spl_{,early_}init() to avoid duplicate code:
Rewrite/expand commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
This reverts commit 8c36e99f21.
There is misunderstanding in commit 8c36e99f21 ("armv8: release
slave cores from CPU_RELEASE_ADDR"). How to bring the slave cores
into U-Boot proper is platform-specific. So, it should be cared
in SoC/board files instead of common/spl/spl.c. As you see SPL
is the acronym of Secondary Program Loader, there is generally
something that runs before SPL (the First one is usually Boot ROM).
How to wake up slave cores from the Boot ROM is really SoC specific.
So, the intention for the spin table support is to bring the slave
cores into U-Boot proper in an SoC specific manner. (this must be
done after relocation. see below.)
If you bring the slaves into SPL, it is SoC own code responsibility
to transfer them to U-Boot proper. The Spin Table defines the
interface between a boot-loader and Linux kernel. It is unrelated
to the interface between SPL and U-Boot proper.
One more thing is missing in the commit; spl_image->entry_point
points to the entry address of U-Boot *before* relocation. U-Boot
relocates itself between board_init_f() and board_init_r(). This
means the master CPU sees the different copy of the spin code than
the slave CPUs enter. The spin_table_update_dt() protects the code
*after* relocation. As a result, the slave CPUs spin in unprotected
code, which leads to unstable behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
spl_init on some boards is called after stack and heap relocation, on
some platforms spl_relocate_stack_gd is called to handle setting the
limit to its value CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN when simple
SPL malloc is enabled during relocation. spl_init should then not
re-assign the old pre-relocation limit when this is defined.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When using ARMv8 with ARMV8_SPIN_TABLE=y, we want the slave cores to
wait on spin_table_cpu_release_addr, until the Linux kernel will "wake" them
by writing to that location. The address of spin_table_cpu_release_addr is
transferred to the kernel using the device tree that is updated by
spin_table_update_dt().
However, if we also use SPL, then the slave cores are stuck at
CPU_RELEASE_ADDR instead and as a result, never wake up.
This patch releases the slave cores by writing spl_image->entry_point to
CPU_RELEASE_ADDR location before the end of the SPL code
(at jump_to_image_no_args()).
That way, the slave cores will start to execute the u-boot and will get to
the spin-table code and wait on the correct address
(spin_table_cpu_release_addr).
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new top-level config option so support booting an image stored
in RAM. This allows to move the RAM boot support into a sparate file
and having a single condition to compile that file.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
There is no CONFIG_OF_PLATDATA, only CONFIG_SPL_OF_PLATDATA, so rename
the two references to CONFIG_OF_PLATDATA to CONFIG_SPL_OF_PLATDATA.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since entry_point and load_addr are addresses, they should be
represented as longs to cover the whole address space and to avoid
warning when compiling the SPL in 64-bit.
Also adjust debug prints to add the 'l' specifier, where needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Create a boot_from_devices() function to handle trying each device. This
helps to reduce the size of the already-large board_init_r() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to name each method so that we can print out this name when
using the method. Currently this happens using a separate function. In
preparation for unifying this, add a name to each method.
The name is only available if we have libcommon support (i.e can use
printf()).
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_SPL_STACK_R is enabled, and spl_init() is called before
board_init_r(), spl_relocate_stack_gd() will move global_data to a new
place in memory. This affects driver model since it uses a list for the
uclasses. Unless this is updated the list will become invalid. When
looking for a non-existent uclass, such as when adding a new one, the loop
in uclass_find() may continue forever, thus causing a hang.
Add a function to correct this rather obscure bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices (e.g. dra7xx) support loading to RAM using DFU without
having direct boot from RAM support. Make sure the linker list
does not contain BOOT_DEVICE_RAM if CONFIG_SPL_RAM_DEVICE is not
enabled.
Fixes: 98136b2f26 ("spl: Convert spl_ram_load_image() to use linker list")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
There is no need for this to be in the BSS region. By moving it we can delay
use of BSS in SPL. This is useful for machines where the BSS region is not
in writeable space. On 64-bit x86, SPL runs from SPI flash and it is easier
to eliminate BSS use than link SPL to run with BSS at a particular
cache-as-RAM (CAR) address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than having a global variable, pass the spl_image as a parameter.
This avoids BSS use, and makes it clearer what the function is actually
doing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Update existing users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. We need two variants - one for BOOT_DEVICE_CPGMAC and one for
BOOT_DEVICE_USBETH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a linker list declaration for this method and remove the explicit
switch() code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Include updating the DFU case]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a linker list macro which can be used to declare an SPL image loader.
Update spl_load_image() to search available loaders for the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Rather than act on the global variable, pass the required struct in as a
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reworks spl_set_header_raw_uboot to allow having both os boot
(which comes with a valid header) and aborting when no valid header is
found (thus excluding raw u-boot.bin images).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Other payload than uImage is currently considered to be raw U-Boot
image. Check also for zImage in Falcon mode.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for loading from UBI volumes on the top of NAND
and OneNAND.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Allwinner devices support SPI flash as one of the possible
bootable media type. The SPI flash chip needs to be connected
to SPI0 pins (port C) to make this work. More information is
available at:
https://linux-sunxi.org/Bootable_SPI_flash
This patch adds the initial support for booting from SPI flash.
The existing SPI frameworks are not used in order to reduce the
SPL code size. Right now the SPL size grows by ~370 bytes when
CONFIG_SPL_SPI_SUNXI option is enabled.
While there are no popular Allwinner devices with SPI flash at
the moment, testing can be done using a SPI flash module (it
can be bought for ~2$ on ebay) and jumper wires with the boards,
which expose relevant pins on the expansion header. The SPI flash
chips themselves are very cheap (some prices are even listed as
low as 4 cents) and should not cost much if somebody decides to
design a development board with an SPI flash chip soldered on
the PCB.
Another nice feature of the SPI flash is that it can be safely
accessed in a device-independent way (since we know that the
boot ROM is already probing these pins during the boot time).
And if, for example, Olimex boards opted to use SPI flash instead
of EEPROM, then they would have been able to have U-Boot installed
in the SPI flash now and boot the rest of the system from the SATA
hard drive. Hopefully we may see new interesting Allwinner based
development boards in the future, now that the software support
for the SPI flash is in a better shape :-)
Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option
in a board defconfig, then building U-Boot and finally flashing
the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with
a help of the sunxi-fel tool:
sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin
The device needs to be switched into FEL (USB recovery) mode first.
The most suitable boards for testing are Orange Pi PC and Pine64.
Because these boards are cheap, have no built-in NAND/eMMC and
expose SPI0 pins on the Raspberry Pi compatible expansion header.
The A13-OLinuXino-Micro board also can be used.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When CONFIG_OF_PLATDATA is enabled, we cannot use the u-boot,dm-pre-reloc
device tree property since the device tree is not available. However,
dt-platdata.c only includes devices which would have been present in the
device tree, and we can assume that all such devices are needed for SPL.
If they were not needed, they would have been omitted to save space.
So in this case, bind all devices regardless of the u-boot,dm-pre-reloc
setting. This avoids needing to add a DM_FLAG_PRE_RELOC to every driver,
thus affecting U-Boot proper also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow configuring the begining of the malloc_f area in SPL.
This patch uses the same CONFIG_MALLOC_F_ADDR established by
the sandbox.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Remove the check for GD_FLG_SPL_INIT in spl_relocate_stack_gd().
The check will always fail. This is because spl_relocate_stack_gd()
is called from ARM's crt0.S and it is called before board_init_r().
The board_init_r() calls spl_init(), which sets the GD_FLG_SPL_INIT
flag.
Note that reserving the malloc area in RAM is not a problem even
if the GD_FLG_SPL_INIT flag is not set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
Support loading FIT in SPL for RAM bootmode.
CONFIG_SPL_LOAD_FIT_ADRESS points to address where FIT image is stored
in memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Call this function before passing control from SPL.
For fpga case it is necessary to enable for example level shifters
when bitstream is programmed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When defined, SPL will proceed to another boot method
if the image it has loaded does not have a signature.
This is useful if the subsequent boot methods are much
more complex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Allow the spl_parse_image_header() to return value. This is convenient
for controlling the SPL boot flow if the loaded image is corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
On some sunxi boards (and presumably also non sunxi boards) u-boot can
be either loaded from a sdcard in a micro-sd slot, or from eMMC.
Print which MMC spl tries to boot from, to help debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As of gcc 5.2.1 for Thumb-1, it is not possible any
more to assign gd from C code, as gd is mapped to r9,
and r9 may now be saved in the prolog sequence, and
restored in the epilog sequence, of any C functions.
Therefore arch_setup_gd(), which is supposed to set
r9, may actually have no effect, causing U-Boot to
use a bad address to access GD.
Fix this by never calling arch_setup_gd() for ARM,
and instead setting r9 in arch/arm/lib/crt0.S, to
the value returned by board_init_f_alloc_reserve().
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
For a simple static string, use panic_str() which prevents calling
printf needlessly.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.
Make SPL take into account the correct mmc device.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we support alternative boot devices, it can sometimes be
unclear which boot devices was actually used. Provide a function to
announce which boot devices are attempted during boot.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce spl_boot_list array, which defines a list of boot devices
that SPL will try before hanging. By default this list will consist
of only spl_boot_device(), but board_boot_order() can be overridden
by board code to populate the array with custom values.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor spl image load code out of board_init_r and into its own
function. This is a preparation for supporting alternative boot
devices.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.
Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
malloc_simple uses a part of the stack as heap, initially it uses
SYS_MALLOC_F_LEN bytes which typically is quite small as the initial
stacks sits in SRAM and we do not have that much SRAM to work with.
When DRAM becomes available we may switch the stack from SRAM to DRAM
to give use more room. This commit adds support for also switching to
a new bigger malloc_simple heap located in the new stack.
Note that this requires spl_init to be called before spl_relocate_stack_gd
which in practice means that spl_init must be called from board_init_f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
spl_relocate_stack_gd only gets called from arch/arm/lib/crt0.S which
clears the bss directly after calling it, so there is no need to clear
it from spl_relocate_stack_gd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As a debug option, add positive confirmation that SPL has completed
execution. This can help with diagnosing the location of unexpected hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.
Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
During the Kconfig conversion one of the changes was missed.
CONFIG_SPL_STACK_R should be CONFIG_SPL_STACK_R_ADDR since we want the
address.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
introduce CONFIG_SPL_PANIC_ON_RAW_IMAGE.
An SPL which define this will panic() if the
image it has loaded does not have a mkimage
signature.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
At present SPL uses a single stack, either CONFIG_SPL_STACK or
CONFIG_SYS_INIT_SP_ADDR. Since some SPL features (such as MMC and
environment) require a lot of stack, some boards set CONFIG_SPL_STACK to
point into SDRAM. They then set up SDRAM very early, before board_init_f(),
so that the larger stack can be used.
This is an abuse of lowlevel_init(). That function should only be used for
essential start-up code which cannot be delayed. An example of a valid use is
when only part of the SPL code is visible/executable, and the SoC must be set
up so that board_init_f() can be reached. It should not be used for SDRAM
init, console init, etc.
Add a CONFIG_SPL_STACK_R option, which allows the stack to be moved to a new
address before board_init_r() is called in SPL.
The expected SPL flow (for CONFIG_SPL_FRAMEWORK) is documented in the README.
Signed-off-by: Simon Glass <sjg@chromium.org>
For version 1:
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Some boards have a special way of loading U-Boot that does not fit with
the existing SPL code. For example sunxi uses an 'FEL' mode where U-Boot
is loaded over USB. Add a CONFIG option and boot mode for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Microblaze currently doesn't use printf in SPL. So this one line was the only
reference to it and resulted in the printf functionality to be pulled in.
Exceeding the 4k size limit. Lets change the printf back to puts so that
Microblaze is fixed again. The only drawback is that the detected boot-device
number will not be printed. But this message alone should be helpful enough
to get an idea where the boot process is broken.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
We had the problem on an AM33xx platform, that SPL detected an
unsupported boot-device. But since this message is a debug message
it took a bit of time to really know, where the hangup in SPL
resulted from. So let's change this debug message to a printf
and also print the detected boot-device that is not supported.
This makes debugging of such cases much easier.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
When enabled, set up driver model for SPL. This allows SPL to use the same
drivers as the main U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
enable to boot only a raw u-boot.bin image from nand with the
CONFIG_SPL_NAND_RAW_ONLY define. This option saves space on
boards where spl space is low.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The parameters of size_t type shall be formatted using "%zu" and not
using "%d".
Precision argument for the "%.*s" parameters shall be of int type.
Signed-off-by: Vasili Galka <vvv444@gmail.com>
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
If image name is longer than 32 bytes, then it will be truncated.
This will remove '\0' at the end of the line, so printf will
go out of string limit.
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
The boot parameters are read from individual variables
assigned for each of them. This been corrected and now
they are stored as a part of the global data 'gd'
structure. So read them from 'gd' instead.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
[trini: Add igep0033 hunk]
Signed-off-by: Tom Rini <trini@ti.com>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
This patch will allow use SPL to boot an u-boot from the OneNAND.
Tested with IGEPv2 board with a OneNAND from Numonyx
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
[trini: Add <spl.h> hunk to fix warning]
Signed-off-by: Tom Rini <trini@ti.com>
In case of usbeth booting just call net_load_image("usb_ether").
This patch also adds CONFIG_SPL_USBETH_SUPPORT and
CONFIG_SPL_MUSB_NEW_SUPPORT config options to enable linking of SPL
against USB gagdet support and new MUSB driver resp.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch enables the SPL framework to be used on powerpc platforms
and not only ARM.
timer_init() does not exist on PPC systems. The timer (decrementer) is
initialized and enabled in interrupt_init() here. And currently
interrupt_init() is called after relocation to SDRAM. Since the only
powerpc SPL implementation (a3m071) doesn't need a timer, let's remove
this timer_init() call for PPC systems.
Signed-off-by: Stefan Roese <sr@denx.de>
Change jump_to_image_no_args() to a weak symbol to allow override by
SoC specific code. This is required by tegra because the SPL runs on
a different CPU from the image it is loading, so tegra specific
initialization is required to start the host CPU. Pass in spl_image
as a parameter for the same reason.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We have not strictly speaking relocated at this point, do not claim that
we have. This is not required for output.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
First, remove the puts from the case where we don't have an mkimage
header as this is somewhat common and intentional for no-arg target
images. Second, rework the final switch statement in board_init_r to,
in the case of !CONFIG_SPL_OS_BOOT be only about doing debug prints
about if we know what the magic is or not (the CONFIG_SPL_OS_BOOT case
is unchanged). Then we call jump_to_image_no_args(). This gives us the
same behavior as before but with slightly smaller code.
Signed-off-by: Tom Rini <trini@ti.com>
By setting CONFIG_SYS_UBOOT_START boards can now use a different entry
point for their U-Boot image. So the U-Boot entry point is not fixed
to CONFIG_SYS_TEXT_BASE any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
On some system (e.g. powerpc), the load-address and entry-point is
located at address 0. So the current approach to load the image
(payload) including the header to the address "load-address - 64"
can't work here.
This patch adds an flag to skip this copying including header to
the SPL framework. By setting SPL_COPY_PAYLOAD_ONLY, only the
playload will be copied. This will be used by the SPL NOR flash
driver on powerpc.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
SPL NOR flash booting support is quite simple. Only copying of the
images is needed.
On MPC5xxx we need to make sure to only use the standard memcpy()
implementation and not the MPC5xxx specific one. As the MPC5xxx
version has some complexity which is not needed for this SPL
booting.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
If an u-boot image is not found, SPL thinks to load a bare
u-boot.bin image with a maximum size of 200KB.
Use CONFIG_SYS_MONITOR_LEN instead.
Signed-off-by: Stefan Roese <stefan.roese@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
In SPL (CONFIG_SPL_FRAMEWORK) board_init_f must setup the stack pointer,
clear the BSS and call board_init_r. We mark this as weak as some
platforms may need to perform additional initalization at this point.
We provide a gd that we know will be in a usable location, once the BSS
has been cleared to help with this as well. Finally, we no longer call
relocate_code so remove that from the armv7 version.
Next, both board_init_f and jump_to_image_linux are going to be
inherently arch-specific, so move these versions to arch/arm/lib/spl.c
Signed-off-by: Tom Rini <trini@ti.com>
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards. We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave
the NAND one in-place as we plan to replace it later in this series.
We use common/spl to avoid linker problems with respect to merging
constant strings in objects. Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.
Signed-off-by: Tom Rini <trini@ti.com>
