Fix wrong environment.h and remove DECLARE_GLOBAL_DATA_PTR
Fixes: 30e39ac7c9 (imx: imx7 Support for Manufacturing Protection)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Update the Kconfig and Makefile to allow build for iMX8M and
restrict the build only in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes: e27bddff4b ("imx8m: Restrict usable memory to space below 4G boundary")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The div loop uses reassign and reuse parent_rate, which causes
the parent rate reference to be wrong after the first loop, the
resulting clock becomes incorrect for div != 1.
Fixes: 829e06bf41 ("imx8ulp: clock: Add MIPI DSI clock and DCNano clock")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is the only place where i.MX8M code does SMCCC call, remove it.
The output has little value as it prints some part of commit ID, and
worse, if there is no SMC handler installed, the code outright hangs
or crashes the system.
By removing this one instance of SMCCC call, U-Boot no longer depends
on SMC handlers and can boot without hanging in any case. If there is
a need to dump this commit ID, use CMD_SMC instead and do 'smc' call
from U-Boot shell or scripts instead of hard-coding SMCCC dependency
into architecture code. This particular code can be replaced by:
=> smc 0xc2000003 0 0 0 0 0 0
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable instruction cache early on to speed up the boot process on i.MX8M.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The FlexSPI NOR boot offset does not require any special handling,
the image_offset is correct in either case (0x1000 for FlexSPI NOR
and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start
of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the
case on MX8MN/MX8MP.
The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in
case of the MX8MN/MX8MP, but fixing that needs additional plumbing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.
If provide both, kernel would failed to request the same gpio twice
and cause fec not work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The extcon is an decrepted property and not used by upstream Linux and
NXP 5.10 kernel, so we remove it before kicking linux in case it is in
dts. Otherwise distro kernel will not able to have usb function.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beside the fused modules on iMX8MP Lite, this part has also fused
GPU3D/2D, LVDS and MIPI DSI.
So we have to disable them for kernel and also disable MIPI DSI
in u-boot DTS for splash screen at runtime.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wait 1ms before issuing the first MRS command to write DDR3 Mode
registers.
There is a requirement to wait a minimum time before issuing command to
the DDR3 device, according to the JEDEC standard this time is 500us
(after RESET_n is de-asserted until CKE becomes active) + tXPR (Reset
CKE Exit time, maximum value 360ns).
It seems that for some reason this is not enforced by the MMDC
controller.
Without this change we experienced random memory initialization failures
with about 2% boot failure rate on specific problematic boards, after
this change we were able to do more than 10.000 power-cycle without a
single failure.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current DDR write level calibration routine always overwrite
the ralat/walat fields to their maximum value, just save
the existing values at the beginning of the calibration routine
and restore it at the end.
In case the delay is estimated by the user to be more than one cycle the
walat should be configured according to that, this is not
automatically done. From the i.MX6 RM:
The user should read the results of the associated delay-line at
MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the
reasonable delay may be above 1 cycle then the user should indicate it at
MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in
MDMISC[WALAT] field. For example, if the result of the write leveling calibration
is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles
then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total
delay will be 2 and 100/256 parts of a cycle
Probably it would just possible to not overwrite the mdmisc register in
the first place, since this is not present in the write_level_calib() example
in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling
Calibration).
Fixes: d339f16911 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable multiple storages for u-boot env:
MMC or SPI flash or NOWHERE for usb
so u-boot can runtime select the storage flash according to boot device.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The TEE memory should be reserved when TEE is present, so need
to runtime update dram bank and memory information according to
tee present or not.
Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable wdog_ad interrupt being triggered by CMC1 to CM33 to let CM33
know A35 reset and reinitialize rpmsg.
Clear wdog_ad and AD_PERIPH reset interrupt after A35 up, otherwise
M33 will always receive interrupt.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Assign the LPAV owner to RTD, and assign LPAV masters and peripherals
to APD. So except the masters and peripherals, other resources
(like DDR, cgc2, pcc5) in LPAV won't be reset during reboot and suspend.
No needs to initialize DDR again after reboot.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable MU0_B clk by default. When M33 image is loaded by Jlink,
the previous method not enable MU0_B clk and not able to communicate
with M33, so let's enable it by default.
And we not put it under kernel dts, because it conflicts with i.MX8QM
suspend/resume logic which requires large change.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When reset with dual boot mode, the LPAV domain won't power down
due to its master is not assigned to APD. So the NICLPAV keeps the
last setting to use PLL4PFD1. So before SPL initialize the PLL4,
we need to switch NICLPAV to FRO192, otherwise system will hang.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add i3c controller clock enable/disable function for imx8ulp.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add functions to check if M33 image is booted and handshake with M33
image via MU. A core notifies M33 to start init by FCR F0, then wait
M33 init done signal by checking FSR F0.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Some printf() have strings that doesn't terminate with end of line
and make the output hard to read.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Disable SPL exception vector which causes issue to ROM patch execution
when SPL calling ROM API.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add settings for operating PLL at 933 MHz. This setting is useful in
case the LPDDR4 DRAM should operate at 1866 MHz or 3733 MT/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
added crypto node in device tree.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX7D - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX6,i.MX6SX,i.MX6UL - added support for JR driver model.
removed sec_init() call, sec is initialized based on
job ring information processed from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Platforms can overwrite the weak definition of spl_mmc_boot_mode() to
determine where to load U-Boot proper from.
For most of them this is a trivial decision based on Kconfig variables,
but it might be desirable the probe the actual device to answer this
question.
Pass the pointer to the mmc struct to that function, so implementations
can make use of that.
Compile-tested for all users changed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ley Foon Tan <ley.foon.tan@inte.com> (for SoCFPGA)
Acked-by: Lokesh Vutla <lokeshvutla@ti.com> (for OMAP and K3)
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid passing around an extra register everywhere, save esr in
pt_regs like the rest. For proper alignment we need to have a second
(unused) register. All the printfs have to be adjusted, since
it's now an unsigned long and not an int.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Instead of a special function, send an event after driver model is inited
and adjust the boards which use this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is used in nxp u-boot tree.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
