This makes it easier to adapt for addition of DMA support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Add at91sam9x5ek board support, this board support the following SoCs
AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35
Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments. This patch adds a simple driver (based on the Linux driver) for
this hardware module.
This patch also adds support to clean and flush dcache during packet send
and receive.
Changes by Sandhya: Added support to clean and flush dcache during packet
send/receive and added timeouts.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
also fix NS16550_init() as we need 16x divider
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
configuration file to enable this feature.
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Hadli, Manjunath <manjunath.hadli@ti.com>
Various devices like EEPROMs require 2-byte address support to
be properly accessed. This patch adds this support for OMAP2/3/4
I2C controller driver.
I've tested it with EEPROM (16 bit address) and TPS65217 chip
(8 bit address) on TI Beaglebone board.
Unfortunately I don't have access to any compatible hardware
with 16bit data register so I can't test if those #ifdef
clauses really work.
CC: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch moves all bootcount implementations into a common
directory: drivers/bootcount. The generic bootcount driver
is now usable not only by powerpc platforms, but others as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Manfred Rudigier <manfred.rudigier@omicron.at>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
Tested-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'sf' of git://git.denx.de/u-boot-blackfin:
sf: spansion: Add support for S25FL256S
sf: winbond: fix page_size
sf: stmicro: add support for N25Q128A
sf: stmicro: add support N25Q128 parts
sf: stmicro: support JEDEC standard two-byte signature
sf: winbond: add W25Q32
cmd_spi: remove superfluous semicolon
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit a4ed3b6 "sf: inline data constants" modified winbond.c's page_size
from 256 to 4096. This prevents either/both of "sf write" writing the
correct data, or "sf read" from reading the correct data back.
This allows U-Boot running on Compulab Tegra to upgrade itself.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
commit 54652991
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips
fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads
to problems for smaller versions of this chip e.g. the 32Mbit version
with deviceid 0x16 on mgcoge. So move the code for this work around to
an own function and check previously manufacturer id and device id to
not break other flashes which don't need this work around.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Philippe De Muyter <phdm@macqel.be>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Erasing flash sectors protected with persistent protection bit (PPB)
mechanism on Spansion flash chips doesn't work. Add sector protection
status checking and sector lock and unlock commands to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Support for DS1388 is added by extending the DS1337 driver. DS1388 is
similar to DS1337. The time registers are offset by 1 (due to support
for hundreds of seconds), and there is no century bit.
The configuration and trickle charge registers are also different.
Tested on hardware with Freescale P2010 and DS1388.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Adds support for Numonyx's N25Q128 SPI flash. These devices
are used on (among others) Avnet Spartan-6 LX9 micro-evaluation
boards. Tested with "sf" commands and CONFIG_ENV_IS_IN_SPI_FLASH.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are more than the M25Pxx serial flashs that can be
used with the stmicro driver, for example: the M25PXxx or
N25Qxx serie. All these chips have burned in the original
stmicro manufacture id 0x20 together with a standard
two-byte signature.
In preperation to support all these chips the stmicro driver
have to decode the full two-byte signature.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
SMDK EVT1 has a different Winbond part, added its part details
to the SPI flash table.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Renesas SH and R-Mobile set up device using PFC.
This provide the framework. Most codes were brought from linux kernel.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The serial device of R8A7740 has the same structure as SH7372 of SH, etc.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The serial device of SH73A0 has the same structure as SH7372 of SH, etc.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The patch "spi: tegra2: rename tegra2_spi.* to tegra_spi.*"
(sha1: edffa63d3d)
renamed tegra2_spi.c to tegra_spi.c
and the patch "Merge branch 'master' of git://git.denx.de/u-boot-microblaze"
(sha1: d978780b2e)
has wrongly resolved confict.
This patch fix it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
* 'master' of git://git.denx.de/u-boot-i2c:
km/common: remove printfs for i2c deblocking code
CONFIG: SMDK5250: I2C: Enable I2C
I2C: Add support for Multi channel
I2C: Modify the I2C driver for EXYNOS5
I2C: Move struct s3c24x0_i2c to a common place.
EXYNOS: PINMUX: Add pinmux support for I2C
EXYNOS5: define EXYNOS5_I2C_SPACING
EXYNOS: Add I2C base address.
EXYNOS: CLK: Add i2c clock
mx6qsabrelite: add i2c multi-bus support
imx-common: add i2c.c for bus recovery support
i.mx53: add definition for I2C3_BASE_ADDR
i.mx: iomux-v3.c: move to imx-common directory
i.mx: iomux-v3.h: move to imx-common include directory
iomux-v3: remove include of mx6x_pins.h
mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
mxc_i2c: add bus recovery support
mxc_i2c: prep work for multiple busses support
mxc_i2c: add i2c_regs argument to i2c_imx_stop
mxc_i2c: add retries
mxc_i2c: check for arbitration lost
mxc_i2c: change slave addr if conflicts with destination.
mxc_i2c: don't disable controller after every transaction
mxc_i2c: place i2c_reset code inline
mxc_i2c: place imx_start code inline
mxc_i2c: remove redundant read
mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
mxc_i2c.c: code i2c_probe as a 0 length i2c_write
mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
mxc_i2c: create i2c_init_transfer
mxc_i2c: clear i2sr before waiting for bit
mxc_i2c: create tx_byte function
mxc_i2c: remove ifdef of CONFIG_HARD_I2C
mxc_i2c: fix i2c_imx_stop
i2c: deblock i2c bus also if accessed before realocation
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Wire up SPI driver
spi: microblaze: Adds driver for Xilinx SPI controller
microblaze: intc: Clear interrupt code
microblaze: Call serial multi initialization
microblaze: Move __udelay implementation
microblaze: Remove extern from board.c
microblaze: Wire up dts configuration
fdt: Add board specific dts inclusion
microblaze: Move individual board linker scripts to common script in cpu tree.
microblaze: Add gpio.h
microblaze: Add missing undefs for UBI and UBIFS
microblaze: Expand and correct configuration comments
microblaze: Enable ubi support
microblaze: Avoid compile error on systems without cfi flash
microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION
Conflicts:
drivers/spi/Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
This adds multiple i2c channel support for I2C.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch modifies the S3C I2C driver to suppport EXYNOS5.
The cahnges made to driver are as follows:
- I2C base address is passed as a parameter to many
functions to avoid multiple #ifdef
- Channel initialisation is moved to a commom funation
as it is required by i2c_init.
- Hardcoding for I2CCON_ACKGEN removed.
- Replaced printf with debug.
- Checkpatch issues resolved.
- Pinmux setting will be done in board/samsung/smdk5250/smdk5250.c
to avoid repeated setting of gpio lines, as it have multi bus support.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
struct s3c24x0_i2c is being moved to common local header file so that
the same can be used by s3c series and exynos series SoCs.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for calling a function that will toggle the
SCL line to return the bus to idle condition.
The actual toggling function is added in a later patch.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This helps in a multiple bus master environment which
is why I also added a wait for bus idle.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
imx_reset is only referenced once so
move to that location.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
imx_start is only referenced once so
move to that location.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
wait_for_sr_state returns i2sr on success
so no need to read again.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Not using udelay gives a more accurate timeout. The current implementation of udelay
in imx-common does not seem to wait at all for a udelay(1).
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
----
V2: Added WATCHDOG_RESET as suggested by Marek Vasut
add error message when stop fails
mxc_i2c: code i2c_probe as a 0 length i2c_write
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Initial code of i2c_read and i2c_write
is identical, move to subroutine.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Let's clear the sr register before waiting for
bit to be set, instead of clearing it after
hardware sets it. No real operational difference here,
but allows combining of i2c_imx_trx_complete and
i2c_imx_bus_busy in later patches.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Use tx_byte function instead of having 3 copies
of the code.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
This is always selected when CONFIG_I2C_MXC is
selected, so it adds no value.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Instead of clearing 2 bits, all the other
bits were set because '|=' was used instead
of '&='.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This is an improved version of the driver patch original
submitted by Graeme Smecher <graeme.smecher@mail.mcgill.ca>
The changes are:
- remove hard coded Xilinx BSP defines (XPAR_SPI_*) and
use CONFIG_SYS_SPI_BASE from config.h instead
- add extensive register struct definitions
- remove offset calculation for register access and
use the new register struct instead
- move default SPI controller configuration from
spi_setup_slave() to spi_claim_bus()
- add spi_set_speed()
- insert SPI controller deactivation in spi_release_bus()
- protect while loops in spi_xfer() with counter / timeouts
- support SPI mode flags: LSB_FIRST, CPHA, CPOL, LOOP
Come from:
http://patchwork.ozlabs.org/patch/71797/
Signed-off-by: Stephan Linz <linz@li-pro.net>
Tested-by: Michal Simek <monstr@monstr.eu>
* 'next' of git://git.denx.de/u-boot:
MPC8xx: Fixup warning in arch/powerpc/cpu/mpc8xx/cpu.c
doc: cleanup - move board READMEs into respective board directories
net: sh_eth: add support for SH7757's GETHER
net: sh_eth: modify the definitions of regsiter
net: sh_eth: add SH_ETH_TYPE_ condition
net: sh_eth: clean up for the SH7757's code
net: fec_mxc: Fix MDC for xMII
net: fec_mxc: Fix setting of RCR for xMII
net: nfs: make NFS_TIMEOUT configurable
net: Inline the new eth_setenv_enetaddr_by_index function
net: allow setting env enetaddr from net device setting
net/designware: Consecutive writes to the same register to be avoided
CACHE: net: asix: Fix asix driver to work with data cache on
net: phy: micrel: make ksz9021 phy accessible
net: abort network initialization if the PHY driver fails
phylib: phy_startup() should return an error code on failure
net: tftp: fix type of block arg to store_block
Signed-off-by: Wolfgang Denk <wd@denx.de>
SH7757 has 2 ETHERs and 2 GETHERs. This patch supports the SH7757's
GETHER. If CONFIG_SH_ETHER_USE_GETHER is defined using SH7757,
the driver handles the GETHER.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
