This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].
SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.
SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.
This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.
SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.
Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmi
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adorns messages generated by dev_xxx with the device and driver
names. It also redirects dev_xxx to log when it is available. The names
of these functions very roughly take inspiration from Linux, but there is
no deeper correlation.
Both struct udevice and struct device are supported when logging, though
logging with struct device is no better than using log_xxx. The latter is
supported because of the large amount of existing code which logs with
struct device.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
This substitutes literal log levels with their symbolic constants.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
In the live tree API ofnode_parse_phandle_with_args, the cell_count
argument must be used when cells_name is NULL.
But this argument is not provided to the live DT function
of_parse_phandle_with_args even it is provided to
fdtdec_parse_phandle_with_args.
This patch adds support of the cells_count parameter in dev_ and
of_node API to allow migration and support of live DT:
- of_parse_phandle_with_args
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently of_match_ptr is used to avoid referencing compatible strings
when OF_CONTROL is not enabled. This behaviour could be improved by
taking into account also OF_PLATDATA, as when this configuration is
enabled the compatible strings are not used at all.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In common clock framework the relation b/w parent and child clocks is
determined based on the udevice parent/child information. A clock
parent could be changed based on devices needs. In case this is happen
the functionalities for clock who's parent is changed are broken. Add
a function that reparent a device. This will be used in clk-uclass.c
to reparent a clock device.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the description of devfdt_get_addr_ptr, this function should
return NULL on failure, but currently it returns (void *)FDT_ADDR_T_NONE.
Fix this by making devfdt_get_addr_ptr return NULL on failure, as
described in the function comments. Also, update the drivers currently
checking (void *)FDT_ADDR_T_NONE to check for NULL.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case of the live tree ofnode_read_addr_cells() and
ofnode_read_size_cells() return the #address-cells and #size-cells defined
in the parent node. With the patch the same is done for a non-live tree.
The only consumer of these functions is currently the CFI flash driver.
This patch fixes the incorrect parsing of the device tree leading to
'saveenv' failing on qemu_arm64_defconfig.
For testing qemu-system-aarch64 has to be called with
-drive if=pflash,format=raw,index=1,file=envstore.img
to provide the flash memory. envstore.img must be 64 MiB large.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
The test flags used by driver model are currently not available to other
tests. Rather than creating two sets of flags, make these flags generic
by changing the DM_ prefix to UT_ and moving them to the test.h header.
This will allow adding other test flags without confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
and use other headers and C inclusions instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
These header file should not be included in other header files. Remove
them and add to each individual file. Add test/test.h to test/ui.h since
that is a reasonable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new uclass for button that implements two functions:
- button_get_by_label
- button_get_status
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
With OF_CONTROL disabled the build fails for
include/dm/read.h:932:10: error: ‘ENOTSUPP’ undeclared (first use in this function)
932 | return -ENOTSUPP;
Fixes: 45224e8f26 ("dm: core: gracefully handle alias seq without of")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Introduce UCLASS_SOC to be used for SOC identification and attribute
matching based on the SoC ID info. This allows drivers to be provided
for SoCs to retrieve SoC identifying information and also for matching
device attributes for selecting SoC specific data.
This is useful for other device drivers that may need different
parameters or quirks enabled depending on the specific device variant in
use.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce UCLASS_SOC to be used for SOC identification and attribute
matching based on the SoC ID info. This allows drivers to be provided
for SoCs to retrieve SoC identifying information and also for matching
device attributes for selecting SoC specific data.
This is useful for other device drivers that may need different
parameters or quirks enabled depending on the specific device variant in
use.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
The Intel Non-High-Definition-Audio Link Table (NHLT) table describes the
audio codecs and connections in a system. Various devices can contribute
information to produce the table.
Add core support for this, based on a structure which is built up through
calls to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Some devices such as GPIO need to override the normal path that would be
generated by driver model. Add a device-tree property for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add a command that shows the individual blocks of data generated by each
device, effectively splitting the full table into its component parts.
This can be helpful for debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function cannot currently be called on the root node. Add a check
for this as well as a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some devices need to inject extra code into the Differentiated System
Descriptor Table (DSDT). Add a method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in inject_dsdt() comments]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Some devices need to generate code for the Secondary System Descriptor
Table (SSDT). Add a method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is convenient to write a length value for preceding a block of data.
Of course the length is not known or is hard to calculate a priori. So add
a way to mark the start on a stack, so the length can be updated when
known.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new file to handle generating ACPI code programatically. This is
used when information must be dynamically added to the tables, e.g. the
SSDT.
Initial support is just for writing simple values. Also add a 'base' value
so that the table can be freed. This likely doesn't happen in normal code,
but is nice to do in tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently when creating an U_BOOT_DEVICE entry a struct driver_info
is declared, which contains the data needed to instantiate the device.
However, the actual device is created at runtime and there is no proper
way to get the device based on its struct driver_info.
This patch extends struct driver_info adding a pointer to udevice which
is populated during the bind process, allowing to generate a set of
functions to get the device based on its struct driver_info.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to prepare for a new support of phandle when OF_PLATDATA is used
drop the const for struct driver_info as this struct will need to be
updated on runtime.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This parameter should be a struct uclass, not struct udevice. Correct it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-By: Michael Trimarchi <michael@amarulasolutions.com>
This struct is not commented but needs it. Also fix the comment in
check_vidconsole_output() about the encoding for the rotation value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Renamed dm "drivers" subcommand to "compat" (as it listed
compatibility strings) and prevent it from segfaulting when
drivers have no of_match populated.
Added a new "drivers" subcommand to dump a list of all known DM
drivers and for each, their uclass id, uclass driver and names of
attached devices.
Added a new "static" subcommand to dump a list of DM drivers with
statically defined platform data.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dev_read_addr_ptr had different semantics depending on whether OF_LIVE was
enabled. This patch converts both implementations to return NULL on error,
and converts all call sites which check for FDT_ADDR_T_NONE to check for
NULL instead. This patch also removes the call to map_physmem, since we
have dev_remap_addr* for those semantics.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clean-up platform data include file by using BIT macro and converting
indentation with spaces to tabs.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Modify the Freescale ESPI driver to support the driver model.
Also resolved the following problems:
===================== WARNING ======================
This board does not use CONFIG_DM_SPI. Please update
the board before v2019.04 for no dm conversion
and v2019.07 for partially dm converted drivers.
Failure to update can lead to driver/board removal
See doc/driver-model/MIGRATION.txt for more info.
====================================================
===================== WARNING ======================
This board does not use CONFIG_DM_SPI_FLASH. Please update
the board to use CONFIG_SPI_FLASH before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If CONFIG_DM_DEV_READ_INLINE is set, dev_read_alias_highest_id() calls
libfdt_get_highest_id(). But this function is only available if we have
libfdt compiled in. If its not available return -1, which matches the
return code for no alias found.
This fixes the following error on omapl138_lcdk:
arm-linux-gnueabi-ld.bfd: drivers/built-in.o: in function `dev_read_alias_highest_id':
/home/mw/repo/u-boot/include/dm/read.h:986: undefined reference to `fdtdec_get_alias_highest_id'
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
For dual ethernet controllers, the HW design may connect ETH phys to
one MDIO ports. So two different ethernet drivers have to share MDIO bus.
Since two ethernet drivers are independent, we can't ensure their probe
order.
To resolve this problem, introduce an eth phy generic driver and uclass.
After eth-uclass binds, we search the mdio node and binds the phy node
with the eth-phy-generic driver.
When one eth driver get its phy device, the parent of phy device will
probe prior than phy device. So this ensure the eth driver ownes the
MDIO bus will be probed before using its MDIO.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch add function used to get the child count of
a ofnode or a device
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Put this in the context along with the other important pointers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Move this code to a generic location so that we can test it with sandbox.
This requires adding a few new fields to acpi_ctx, so drop the local
variables used in the original code.
Also use mapmem to avoid pointer-to-address casts which don't work on
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
A device may want to write out ACPI tables to describe itself to Linux.
Add a method to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add functions to iterate on all property with livetree
- dev_read_first_prop
- dev_read_next_prop
- dev_read_prop_by_prop
and
- ofnode_get_first_property
- ofnode_get_next_property
- ofnode_get_property_by_prop
And helper: dev_for_each_property
For example:
struct ofprop property;
dev_for_each_property(property, config) {
value = dev_read_prop_by_prop(&property, &propname, &len);
or:
for (res = ofnode_get_first_property(node, &property);
!res;
res = ofnode_get_next_property(&property))
{
value = ofnode_get_property_by_prop(&property, &propname, &len);
....
}
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl6YdaMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYLRwf8C+vKmERVLLcrMZMMiLctbY2kVflJV8zG
RjFwBcazZDPYjtHqClFZtJyIDYzgkVQRo+QPcdLxjcA+gjSXdteeRa0XTsBTXOZQ
kbs7yBkL+rCIO2WyXtuyajsmDMQtqM5vYgeBdTeYnJu7NVxwRMYrUqqAKLolNpIN
SKNYz+a8OEOG2EetbTdwwrmSpNy/cZ3wDGYK25DFTte8/vCZMRBTPiiNSrLp/RsM
xIojRcLqzARwpvPfFZ8psASKei9+5oIICUrNvwwQGtjepvZwdFQEl90SKaHw8kMf
sP9rxuqlEN5ec6xnMTUgwfnyBZgNIMSeb4KVPP1rxN2eAa5+bK1OlQ==
=gyyY
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10apr20-take2' of git://git.denx.de/u-boot-dm
Functions for reading indexed values from device tree
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
The content dm_ofnode_pre_reloc() is identical with ofnode_pre_reloc()
defined in drivers/core/ofnode.c and used only three times:
- drivers/core/lists.c:lists_bind_fdt()
- drivers/clk/at91/pmc.c::at91_clk_sub_device_bind
- drivers/clk/altera/clk-arria10.c::socfpga_a10_clk_bind
So this function dm_ofnode_pre_reloc can be removed and replaced
by these function calls by ofnode_pre_reloc().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
The patch adds helper functions to allow reading a single indexed u32
value from a device-tree property containing multiple u32 values, that
is an array of integers.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
When removing a device the power domains it uses are generally powered
off. But when we are trying to unbind all devices (e.g. for running tests)
we don't want to probe a device in the 'remove' path.
Add a new flag to skip this power-down step.
Signed-off-by: Simon Glass <sjg@chromium.org>
The ASL compiler cannot handle C structures and the like so needs some
sort of header guard around these.
We already have an __ASSEMBLY__ #define but it seems best to create a new
one for ACPI since the rules may be different.
Add the check to a few files that ACPI always includes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add a sandbox test for the basic ACPI functionality we have so far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
ACPI (Advanced Configuration and Power Interface) is a standard for
specifying information about a platform. It is a little like device
tree but the bindings are part of the specification and it supports an
interpreted bytecode language.
Driver model does not use ACPI for U-Boot's configuration, but it is
convenient to have it support generation of ACPI tables for passing to
Linux, etc.
As a starting point, add an optional set of ACPI operations to each
device. Initially only a single operation is available, to obtain the
ACPI name for the device. More operations are added later.
Enable ACPI for sandbox to ensure build coverage and so that we can add
tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In various cases a power domain must stay enabled after device
removal when booting OS (i.e. serial debug console or display).
Add a flag to selectively skip switching off a power domain.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
It is sometimes useful to find a device in a uclass using only its driver
data. The driver data often indicates the 'subtype' of the device, e,g,
via its compatible string.
Add a function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have uclass_foreach_dev() which requires that uclass_get()
be called beforehand to find the uclass. This is good if we suspect that
that function might fail, but often we know that the uclass is available.
Add a new helper which does this uclass_get() automatically, so that only
the uclass ID is needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This adds a subcommand to dm to dump out what drivers are installed, and their
compatible strings. I have found this useful in ensuring that I have the correct
drivers compiled, and that I have put in the correct compatible strings.
Signed-off-by Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to process all children, making sure they are
probed first. Add functions to help with this and a macro to make it more
convenient.
Signed-off-by: Simon Glass <sjg@chromium.org>
When generating ACPI tables we need to make sure that all devices have
read their platform data, so that they can generate the tables correctly.
Rather than adding this code in ACPI, create a core function to handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to read a property from the chosen node, providing access
to its length. Update ofnode_get_chosen_string() to make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new function to read a property that supports reading the length as
well.
Reimplement ofnode_read_string() using it and fix its comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions do not modify the device so should use a const pointer to
it. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions do not modify the device so should use a const pointer to
it. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
The devres functionality has very few users in U-Boot, but it still should
have tests. Add a few basic tests of the main functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these functions are lumped in with the core device functions.
They have their own #ifdef to control their availability, so it seems
better to split them out.
Move them into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to avoid allocating platform data twice. This could happen if
device_probe() is called after device_ofdata_to_platdata() for the same
device.
Add a flag to track whether device_ofdata_to_platdata() has been called on
a device. Check the flag to make sure it doesn't happen twice, and clear
the flag when the data is freed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new internal function, device_ofdata_to_platdata() to handle
allocating private space associated with each device and reading the
platform data from the device tree.
Call this new function from device_probe().
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a uclass for reading a random number seed from a random number
generator device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Primary-to-Sideband bus (P2SB) is used to access various peripherals
through memory-mapped I/O in a large chunk of PCI space. The space is
segmented into different channels and peripherals are accessed by
device-specific means within those channels. Devices should be added in
the device tree as subnodes of the p2sb.
This adds a uclass and enables it for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Intel x86 SoCs have a power manager/controller which handles several
power-related aspects of the platform. Add a uclass for this, with a few
useful operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Early in boot it is necessary to decode the PCI device/function values for
particular peripherals in the device tree or of-platdata. This is needed
in TPL where CONFIG_PCI is not defined.
To handle this, move pci_get_devfn() into a file that is built even when
CONFIG_PCI is not defined.
Also add a function for use by of-platdata, to convert a reg property to
a pci_dev_t.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If the offset is -1 this function correctly sets up a null ofnode. But if
the offset is any other negative number (e.g. -FDT_ERR_BADPATH) then it
does the wrong thing.
An offset of -1 in ofnode indicates that the ofnode is not valid. Any
other negative value is not handled by ofnode_valid(). We could of course
change that function, but it seems much better to always use the same
value for an invalid node.
Fix it by setting the offset to -1 if it is invalid for any reason.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Remove the pinctrl_decode_pin_config() API, because this
function is unused and not compatible with livetree
(it uses fdtdec_get_bool instead of ofnode API).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Support for UFS Host Controller Interface (UFSHCI) for communicating
with Universal Flash Storage (UFS) devices. The steps to initialize the
host controller interface are the following:
- Initiate the Host Controller Initialization process by writing to the
Host controller enable register.
- Configure the Host Controller base address registers by allocating a
host memory space and related data structures.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
Also register this host controller as a SCSI host controller.
Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to
U-boot.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
In some remoteproc cases, enabling the power domain of the core will
start running the core. In such cases image should be loaded before
enabling the power domain. But the current DM framework enables the
power-domain by default during probe. This is causing the remotecore
to start and crash as there is no valid image loaded.
In order to avoid this introduce a DM flag that doesn't allow for
enabling/disabling the power-domain by DM framework.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When DEVRES is not set, devm_kmalloc_array() is spelled
devm_kmaloc_array() (with one 'l' only).
Fixing it so that the name is the same with and without DEVRES.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Default address cells value on the livetree access function
returns the wrong value. Fix this so that the value returned
corresponds to the device tree specification.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
At present PCI address transaction is not supported so drivers must
manually read the correct BAR after reading the device tree info. The
ns16550 has a suitable implementation, so move this code into the core
DM support.
Note that there is no live-tree equivalent at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the unclear comments in test.dts]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Sandbox pci works using emulation drivers which are currently children of
the pci device:
pci-controller {
pci@1f,0 {
compatible = "pci-generic";
reg = <0xf800 0 0 0 0>;
emul@1f,0 {
compatible = "sandbox,swap-case";
};
};
};
In this case the emulation device is attached to pci device on address
f800 (device 1f, function 0) and provides the swap-case functionality.
However this is not ideal, since every device on a PCI bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
Worse, child devices cannot be probed before their parents. This forces
us to use 'find' rather than 'get' to obtain the emulator device. In fact
the emulator devices are never probed. There is code in
sandbox_pci_emul_post_probe() which tries to track when emulators are
active, but at present this does not work.
A better approach seems to be to add a separate node elsewhere in the
device tree, an 'emulation parent'. This could be given a bogus address
(such as -1) to hide the emulators away from the 'pci' command, but it
seems better to keep it at the root node to avoid such hacks.
Then we can use a phandle to point from the device to the correct
emulator, and only on sandbox. The code to find an emulator does not
interfere with normal pci operation.
Add a new UCLASS_PCI_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. Update the existing
device trees and the code for finding an emulator.
This brings PCI emulators more into line with I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 3 typos in the commit message;
encode bus number in the labels of swap_case_emul nodes;
mention commit 4345998ae9 in sandbox_pci_get_emul()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
We have a 'safe' version of this function but sometimes it is not needed.
Add a normal version too and update a few places that can use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function returns -ENODEV when there is no device. This is
inconsistent with other functions, such as uclass_find_next_device(),
which returns 0.
Update it and tidy up the incorrect '-1' values in the comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds functions dev_read_u64_default & dev_read_u64
to read unsigned 64-bit values from devicetree.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The "serial_stm32.h" is only used by drivers/serial/serial_stm32.c
and it is the file ./drivers/serial/serial_stm32.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Current dev_read_*() API lacks support to get address and size
of a "reg" property by name or index. Add support for the same.
Livetree support has been added but not tested on real hardware.
The existing unit tests testing reading address from device-tree
have been updated to test address as well as size.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The uclass_next_device() routine continues a previously started device
iteration. Change the description that is copied from
uclass_first_device().
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
The comments of dev_read_name() wrongly describe "node" as its
parameter.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the following functions to translate DMA address to CPU address:
- dev_translate_dma_address()
- ofnode_translate_dma_address()
- of_translate_dma_address()
- fdt_translate_dma_address()
These functions work the same way as xxx_translate_address(), with the
difference that the translation relies on the "dma-ranges" property
instead of the "ranges" property.
Add related test. Test report:
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Adds a class for MDIO MUXes, which control access to a series of
downstream child MDIOs.
MDIO MUX drivers are required to implement a select function used to switch
between child buses.
MUX children are registered as MDIO buses and they can be used just like
regular MDIOs.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
Introduce new UCLASS_PCI_EP class for handling PCI endpoint
devices, allowing to set various attributes of the PCI endpoint
device, such as:
* configuration space header
* BAR definitions
* outband memory mapping
* start/stop PCI link
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add documentation for the pre-reloc property in SPL and TPL device-tree:
- u-boot,dm-pre-proper
- u-boot,dm-pre-reloc
- u-boot,dm-spl
- u-boot,dm-tpl
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended for devices that do not need any features from the
uclass, including binding children.
This will typically be used by devices that are used to bind child devices
but do not use dm_scan_fdt_dev() to do it. That is for example the case of
several USB wrappers that have 2 child devices (1 for device and 1 for
host) but bind only one at a any given time.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add drive-strength-microamp property support to allow drive strength in uA
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
It was returning an int, which doesn't work if the u32 it is reading,
or the default value, will overflow a signed int.
While it could be made to work, when using a C standard/compiler where
casting negative signed values to unsigned has a defined behavior,
combined with careful casting, it seems obvious one is meant to use
ofnode_read_s32_default() with signed values.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Add ofnode_get_addr_size_index function to fetch the address
and size of the reg space based on index.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The cache UCLASS will be used for configure settings that can be found
in a CPU's L2 cache controller.
Add a uclass and a test for cache.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add callback to configure, and de-configure, pin as a GPIO on the
pin controller side. This matches similar functionality in Linux
and aims to replace the ad-hoc implementations present in U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alex Kiernan <alex.kiernan@gmail.com>
Cc: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick DELAUNAY <patrick.delaunay@st.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Testing has shown that the current DM implementation of a platform /
board specific translation offset, as its needed for the SPL on MVEBU
platforms is buggy. The translation offset is confingured too late,
after the driver bind functions are run. This may result in incorrect
address translations. With the current implementation its not possible
to configure the offset earlier, as the DM code has not run at all.
This patch now removed the set_/get_translation_offset() calls and
moves the translation offset into the GD variable translation_offset.
This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled.
This option is enabled only for MVEBU on ARM32 platforms, where its
currenty needed and configured in the SPL.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pierre Bourdon <delroth@gmail.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Pierre Bourdon <delroth@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
The function dm_ofnode_pre_reloc should be used instead
of the function dm_fdt_pre_reloc and avoid duplicated code.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 5ff7768892.
As noted in the comment, the function pinctrl_decode_pin_config_dm()
only served as a temporary solution.
Since the function has no users anymore, we can remove it again.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is wrapper for calling of_alias_get_highest_id() when live tree is
enabled and fdtdec_get_alias_highest_id() if not.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same functionality was added to Linux for i2c bus registration with this
commit message:
"
of: base: add function to get highest id of an alias stem
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
"
Add it also to U-Boot for DM I2C support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinctrl_decode_pin_config_dm() is basically a feature-equivalent
implementation of pinctrl_decode_pin_config(), which operates
on struct udevice devices and uses the dev_read_*() API.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The current dev_read...() functions use s32 and u32 which are convenient
for device tree but not so useful for normal code, which often wants to
use normal integers for values.
Add a helper which supports returning an unsigned int. Also add signed
versions of the unsigned readers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2s bus is commonly used with audio codecs. It provides a way to
stream digital data sychronously in both directions. U-Boot only supports
audio output, so this uclass is very simple, with a single tx_data()
method.
Add a uclass and a test for i2s.
Signed-off-by: Simon Glass <sjg@chromium.org>
An audio codec provides a way to convert digital data to sound and vice
versa. Add a simple uclass which just supports setting the parameters for
the codec.
Signed-off-by: Simon Glass <sjg@chromium.org>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
The original bootcount methods do not provide an interface to DM and
rely on a static configuration for I2C devices (e.g. bus, chip-addr,
etc. are configured through defines statically). On a modern system
that exposes multiple devices in a DTS-configurable way, this is less
than optimal and a interface to DM-based devices will be desirable.
This adds a simple driver that is DM-aware and configurable via DTS.
If ambiguous (i.e. multiple bootcount-devices are present) the
/chosen/u-boot,bootcount-device property can be used to select one
bootcount device.
Initially, this provides support for the following DM devices:
* RTC devices
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
If OF_CONTROL is not enabled and DM_SEQ_ALIAS is enabled, we must
assign an alias (requested sequence number) to devices that belongs to a
class with the DM_UC_FLAG_SEQ_ALIAS flag. Otherwise
uclass_find_device_by_seq() cannot be used to get/probe a device. In
particular i2c_get_chip_for_busnum() cannot be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is uclass for Hardware Spinlocks.
It implements two mandatory operations: lock and unlock
and one optional relax operation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
This functions allow us to get and remap I/O addresses by name, which is useful when there are multiple reg addresses indexed by reg-names property.
This is needed in bmips dma/eth patch series, but can also be used on many
other drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The comment in uclass-id.h states that
"U-Boot uclasses start here - in alphabetical order"
but the subsequent list is not sorted alphabetically.
This reestablishes order.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sandbox i2c works using emulation drivers which are currently children of
the i2c device:
rtc_0: rtc@43 {
reg = <0x43>;
compatible = "sandbox-rtc";
emul {
compatible = "sandbox,i2c-rtc";
};
};
In this case the emulation device is attached to i2c bus on address 0x43
and provides the Real-Time-Clock (RTC) functionality.
However this is not ideal, since every device on an I2C bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
A better approach seems to be to add a separate node on the bus, an
'emulation parent'. This can be given a bogus address (such as 0xff) and
hides all the emulators away. Then we can use a phandle to point from the
device to the correct emualtor, and only on sandbox. The code to find an
emulator does not interfere with normal i2c operation.
Add a new UCLASS_I2C_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. This will be used in a
follow-on patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is currently at the top in the space for internal use. But this
uclass is used outside driver model and test code. Move it into the
correct alpha order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add two functions which can find a child device by uclass or by name.
The first is useful with Multi-Function-Devices (MFDs) to find one of a
particular type. The second is useful when only the name is known.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function may be useful to code outside of the code driver-model
implementation. Export it and add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename platform_data include file as spi_pl022.h from pl022_spi.h,
this is generic notation used for spi platdata include files.
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
pl022 spi driver support both OF_CONTROL and PLATDATA, this
patch is trying to simplify the code that differentiating
platdata vs of_control.
- Move OF_CONTROL code at one place
- Handle clock setup code directly in pl022_spi_ofdata_to_platdata
Acked-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
pinmux command allows to :
- list all pin-controllers available on platforms
- select a pin-controller
- display the muxing of all pins of the current pin-controller
or all pin-controllers depending of given options
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
cmd: pinmux: Fix pinmux command
if "pinmux status" command is used without having
set dev using "pinmux dev", print pinmux usage
Reviewed-by: Simon Glass <sjg@chromium.org>
Add uclass_foreach_dev_probe() which iterates through
devices of a given uclass. Devices are probed if necessary
and are ready to use.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Similarly to uclass_first_device_err(), add uclass_next_device_err()
which returns an error if there are no next devices in that uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add pinctrl_get_pin_name() and pinctrl_get_pins_count() methods
to obtain pin's name and pin's muxing given a pin reference.
This will be used by the new pinmux command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add get_pin_muxing() which allows to display the muxing
of a given pin belonging to a pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new virtio uclass driver for “virtio” [1] family of
devices that are are found in virtual environments like QEMU,
yet by design they look like physical devices to the guest.
The uclass driver provides child_pre_probe() and child_post_probe()
methods to do some common operations for virtio device drivers like
device and driver supported feature negotiation, etc.
[1] http://docs.oasis-open.org/virtio/virtio/v1.0/virtio-v1.0.pdf
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test case to cover uclass driver's child_post_probe() method.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some buses need to set up their child devices after they are probed.
Support a common child_post_probe() method for the uclass.
With this change, the two APIs uclass_pre_probe_device() and
uclass_post_probe_device() become symmetric.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pre_reloc_only parameter description currently only mentions
drivers with the DM_FLAG_PRE_RELOC flag, but does not mention the
special device tree properties. Correct them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the comments of several APIs (eg: dm_init_and_scan()) say:
@pre_reloc_only: If true, bind only drivers with the DM_FLAG_PRE_RELOC
flag. If false bind all drivers.
The 'Pre-Relocation Support' chapter in doc/driver-model/README.txt
documents the same that both device tree properties and driver flag
are supported.
However the implementation only checks these special device tree
properties without checking the driver flag at all. This updates
lists_bind_fdt() to consider both scenarios.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Squashed in http://patchwork.ozlabs.org/patch/996473/ :
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds a new API dm_ofnode_pre_reloc(), a livetree equivalent
API of dm_fdt_pre_reloc().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Davanci spi driver has DM support already, this patch
add support for platdata so-that SPL can use it for
low foot-print.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com>
At present ofnode_read_fmap_entry() reads a flash map entry in a format
which is not supported by binman. To allow use to use binman-format
descriptions, update this function.
Also add a simple test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices have children and want to press an existing inactive child
into service when needed. Add a function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Quite a few functions do not actually modify the device that is passed in.
Update the function signatures to reflect that.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no reason why this feature should not be supported for uclass-
private data. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adds a uclass to interface with a TEE (Trusted Execution Environment).
A TEE driver is a driver that interfaces with a trusted OS running in
some secure environment, for example, TrustZone on ARM cpus, or a
separate secure co-processor etc.
The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.
The over all design is based on the TEE subsystem in the Linux kernel,
tailored for U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We cannot use device structures to disable devices, since getting
them with the API functions would bind and activate the device, which
would fail if the underlying device does not exist.
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement a set of functions to manipulate properties in a live device
tree:
* ofnode_write_prop() to set generic properties of a node
* ofnode_write_string() to set string properties of a node
* ofnode_set_enabled() to either enable or disable a node
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
We might want to access data stored onto one wire EEPROMs.
Create a framework to provide a consistent API.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked patch]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is file system generic loader which can be used to load
the file image from the storage into target such as memory.
The consumer driver would then use this loader to program whatever,
ie. the FPGA device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Some devices offer a text-based OSD (on-screen display) that can be
programmatically controlled (i.e. text displayed on).
Add a uclass to support such devices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
This adds support for the ARM PL022 SPI controller for the standard
variant (0x00041022) which has a 16bit wide and 8 locations deep TX/RX
FIFO.
A few parts were borrowed from the Linux kernel driver.
Cc: Armando Visconti <armando.visconti@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
The comment of child_pre_probe, one of the 'struct uclass_driver'
members, is currently missing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds ofnode_by_prop_value() to search for nodes with a given property
and value, an ofnode version of fdt_node_offset_by_prop_value().
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Also add a 'drv' parameter to filter the children to remove/unbind.
Exporting those functions is a preparatory work for the addition of the
bind/unbind commands.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also add device_find_global_by_ofnode() that also find a device based on
the OF node, but doesn't probe the device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This function is the reciprocal of uclass_find_device().
It will be used to print the index information in dm tree dump.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a uclass for AXI (Advanced eXtensible Interface) busses, and a
driver for the gdsys IHS AXI bus on IHS FPGAs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't have the live-tree version of fdtdec_get_pci_vendev().
This adds the API.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct typos in the comment block of uclass_first/next_device_check().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a way to decode a memory region, including the memory type (sram or
sdram) and its start address and size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new device_bind_ofnode() function which can bind a device given its
ofnode. This allows binding devices more easily with livetree nodes.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a 32-bit version of this function. Add a 64-bit version as well so
we can easily read 64-bit ints from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
device_is_compatible() takes udevice, but there is no such a helper
that takes ofnode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit 286ede6 ("drivers: core: Add translation in live tree case") made
dev_get_addr always use proper bus translations for addresses read from
the device tree. But this leads to problems with certain busses, e.g.
I2C busses, which run into an error during translation, and hence stop
working.
It turns out that of_translate_address() and fdt_translate_address()
stop the address translation with an error when they're asked to
translate addresses for busses where #size-cells == 0 (comment from
drivers/core/of_addr.c):
* Note: We consider that crossing any level with #size-cells == 0 to mean
* that translation is impossible (that is we are not dealing with a value
* that can be mapped to a cpu physical address). This is not really specified
* that way, but this is traditionally the way IBM at least do things
To fix this case, we check in both the live-tree and non-live tree-case,
whether the bus of the device whose address is about to be translated
has size-cell size zero. If this is the case, we just read the address
as a plain integer and return it, and only apply bus translations if the
size-cell size if greater than zero.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Fixes: 286ede6 ("drivers: core: Add translation in live tree case")
Reviewed-by: Simon Glass <sjg@chromium.org>
Add api for who can not get phandle from a device property.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Contains all the pfe header files.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We need to get ofnode from a phandle, add interface to support
both live dt and fdt.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The Rockchip video drivers need to walk the ofnode-parrents to find
an enclosing device that has a UCLASS_DISPLAY driver bound. This
adds a ofnode_get_parent()-function that returns the parent-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Each uclass has a driver name which we can use to look up the uclass. This
is useful for logging, where the uclass ID is used as the category.
Add a function to handle this, as well as a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We are switching to a model where a serial device doesn't even get probed when
it's not muxed properly, so we don't need device specific disabling
functionality anymore.
Signed-off-by: Alexander Graf <agraf@suse.de>
There are some typos in the documentation of some functions in read.h;
fix those.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices
For each EFI driver the uclass
* creates a handle
* adds the driver binding protocol
The uclass provides the bind, start, and stop entry points for the driver
binding protocol.
In bind() and stop() it checks if the controller implements the protocol
supported by the EFI driver. In the start() function it calls the bind()
function of the EFI driver. In the stop() function it destroys the child
controllers.
The EFI block driver binds to controllers implementing the block io
protocol.
When the bind function of the EFI block driver is called it creates a
new U-Boot block device. It installs child handles for all partitions and
installs the simple file protocol on these.
The read and write functions of the EFI block driver delegate calls to the
controller that it is bound to.
A usage example is as following:
U-Boot loads the iPXE snp.efi executable. iPXE connects an iSCSI drive and
exposes a handle with the block IO protocol. It calls ConnectController.
Now the EFI block driver installs the partitions with the simple file
protocol.
iPXE uses the simple file protocol to load Grub or the Linux Kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: add comment on calloc len]
Signed-off-by: Alexander Graf <agraf@suse.de>
dev_read_u32_default() always returns something even when the property
is missing. So, it is impossible to do nothing in the case. One
solution is to use ofnode_read_u32() instead, but adding dev_read_u32()
will be helpful.
BTW, Linux has an equvalent function, device_property_read_u32();
it is clearer that it reads a property. I cannot understand the
behavior of dev_read_u32() from its name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Sync with Linux commit 30a7acd573899fd8b("Linux 4.15-rc6")
to use enum pin_config_param.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As we discussed before in ML, dm_dbg() causes undefined reference
error if #define DEBUG is added to users, but not drivers/core/util.c
We do not need this macro because we can use pr_debug() instead, and
it is pretty easy to enable it for the DM core by using ccflags-y.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Many drivers had started to use dev_err, dev_info, etc. for log
functions. Currently, we are relying on <linux/compat.h>, but I
guess the best home is <dm/device.h>, taking into account that
Linux defines them in <linux/device.h>.
For now, I am leaving the ones in <linux/compat.h> because lots of
Linux-originated code uses dev_*(), but the first argument is not
struct udevice, so we need to ignore the bogus argument. More
efforts are needed to iron out the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
dev_read_string_count() is used to get the number of strings in a
stringlist.
dev_read_string_index() is used to get a string in the stringlist based on
its position in the list.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The dev_read_addr_ptr() mimics the behaviour of the devfdt_get_addr_ptr(),
retrieving the first address of the node's reg-property and returning
it as a pointer (or NULL on failure).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, all fixed-clock declared in "clocks" node in device tree
can be binded by clk_fixed_rate.c driver only if each of them have
the "simple-bus" compatible string.
This constraint has been invoked here [1].
This patch offers a solution to avoid adding "simple-bus" compatible
string to nodes that are not busses.
[1] https://patchwork.ozlabs.org/patch/558837/
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the IDE driver to driver model so that block read and
write are fully functional.
Fixes: b7c6baef ("x86: Convert MMC to driver model")
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Linux supports platform_get_resource_byname() to look up a resource
by name.
We want a similar helper. It is useful when a device node has named
register regions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new uclass id and block interface type for NVMe.
Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is usefull to get phandle number contained
in a property list.
For example, this allows to allocate the right amount
of memory to keep clock's reference contained into the
"clocks" property.
To implement it, either of_count_phandle_with_args() or
fdtdec_parse_phandle_with_args() are used respectively
for live tree and flat tree.
By passing index = -1, these 2 functions returns the
number of phandle contained into the property list.
Add also the dev_count_phandle_with_args() based on
ofnode_count_phandle_with_args()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We sometimes need to read a resource from an arbitrary node. In any case
for consistency we should not put the live-tree switching code in
a dev_read_...() function. Update this to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
DT property values can be strings as well as integers. This is why
of_get_property/fdt_getprop returns an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This allow to remove include/dm/platform_data/serial_stm32x7.h
which was included in the past by stm32x7 driver and by
stm32f746-disco.c board file.
Since patch 42bf5e7c27 "serial: stm32f7: add device tree support"
this file is no more needed in board file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
This function returns the pointer to the value of a node property.
The current name ofnode_read_prop() is confusing. Follow the naming
of_get_property() from Linux.
The return type (const u32 *) is wrong. DT property values can be
strings as well as integers. This is why of_get_property/fdt_getprop
returns an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
The of_n_addr_cells() and of_n_size_cells() functions are useful for
getting the size of addresses in a node, but in a few places U-Boot needs
to obtain the actual property value for a node without walking up the
stack. Add functions for this and just the existing code to use it.
Add a comment to the existing ofnode functions which do not do the right
thing with a flat tree.
This fixes a problem reading PCI addresses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
This function allows a device's status to be read. This indicates whether
the device should be enabled or disabled.
Note: In normal operation disabled devices will not be present in the
driver-model tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Add a function which reads resources from a device, such as the device
hardware address. This uses the "reg" property in the device.
Unlike other functions there is little sense in inlining this when
livetree is not being used because it has some logic in it and this would
just bloat the code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
This provides a way to find the number of strings in a string list. Add it
and also fix up the comment for ofnode_read_string_index().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Sometimes it is useful to iterate through all devices in a uclass and
skip over those which do not work correctly (e.g fail to probe). Add two
new functions to provide this feature.
The caller must check the return value each time to make sure that the
device is valid. But the device pointer is always returned.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some tests which check the behaviour of uclass_first_device() and
uclass_next_device() when probing of a device fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add some definitions and helpers for livetree in the main of.h header
file. These include:
- reading multi-cell integers
- default number of address/size cells
- functions for comparing names
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests require either livetree or flat tree. Add flags to allow the
tests to specify this. Adjust the test runner to run with livetree (if
supported) and then flat tree.
Some video tests are quite slow and running on flat tree adds little extra
test value, so run these on livetree only.
Signed-off-by: Simon Glass <sjg@chromium.org>
When starting up driver model with a live tree we need to scan the tree
for devices. Add code to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function to us an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function to use an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a live tree is being used we need to record the node that was used to
create the device. Update device_bind_with_driver_data() to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the live tree is supported some functions need to change a little.
Add an implementation which is used when not inlining these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is common to read a device-tree property from the node associated with
a device. Add convenience functions to do this so that drivers do not need
to deal with accessing the ofnode from the device.
These functions all start with 'dev_read_' to provide consistent naming
for all functions which read information from a device's device tree node.
These are inlined when using the flat DT to save code size. The live tree
implementation is added in a later commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some functions deal with structured data rather than simple data types.
It makes sense to have these in their own file. For now this just has a
function to read a flashmap entry. Move the data types also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add functions to access addresses in the device tree. These are brought
in from Linux 4.10.
Also fix up the header guard for fdtaddr.h to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since U-Boot supports both a live tree and a flat tree, we need an easy
way to access the tree without worrying about which is currently active.
To support this, U-Boot has the concept of an ofnode, which can refer
either to a live tree node or a flat tree node.
For the live tree, the reference contains a pointer to the node (struct
device_node *) or NULL if the node is invalid. For the flat tree, the
reference contains the node offset or -1 if the node is invalid.
Add a basic set of operations using ofnodes. These are implemented by
using either libfdt functions (in the case of a flat DT reference) or
the live-tree of_...() functions.
Note that it is not possible to have both live and flat references active
at the same time. As soon as the live tree is available, everything in
U-Boot should switch to using that. This avoids confusion and allows us to
assume that the type of a reference is simply based on whether we have a
live tree yet, or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a basic assortment of functions to access the live device tree. These
come from Linux v4.9 and are modified for U-Boot to the minimum extent
possible. While these functions are now very stable in Linux, it will be
possible to merge in fixes if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a Kconfig option to enable a live device tree, built at run time from
the flat tree. Also add structure definitions and a root node.
Signed-off-by: Simon Glass <sjg@chromium.org>
With live tree we need a struct device_node * to reference a node. With
the existing flat tree, we need an int offset. We need to unify these into
a single value which can represent both.
Add an ofnode union for this and adjust existing code to move to this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used in one place. It is better to just declare it
internally since there is a simpler replacement for use outside the
driver-model core code.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
