Add DT nodes related to DMA and CPSW to -u-boot.dtsi to get networking
up on J721e EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Based on upstream-linux
See https://github.com/torvalds/linux/commit/f66b2aff.
However made the XSMI register window 0x16 (22) bytes per my reading
of the functional spec. Similar commits in Marvels own repo bump it
to 0x200 (512) bytes but I did not see the reasoning for that.
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/4d932b4.
Also added device-name attributes to prevent ambiguity in the `mdio`
command.
Signed-off-by: Nevo Hed <nhed+github@starry.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The AM654 SoC doesn't allow to disabling RGMII TX internal delay in CPSW2G
MAC. Hence, change CPSW2G interface mode to "rgmii-rxid" - RGMII with
internal RX delay provided by the PHY, the MAC will add an TX delay in this
case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
You can directly specify the label as the operand for ljmp.
This commit saves 4-byte code.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed the gas warning]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This file defines 'a32' and 'o32' macros to avoid magic numbers
of operand/address-size prefixing.
GAS supports 'data32' and 'addr32' for that purpose.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
- rockchip pwm driver update to support all the SoCs
- RK3308 GMAC and pinctrl support
- More UART interface support on PX30 and pmugrf reg fix
- Fixup on misc for eth_addr/serial#
- Other updates on variant SoCs
When we want to use plus pinctrl feature, we need to enable
them at spl.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This PWM driver can be used to support pwm functions
for on all Rockchip Socs.
The previous chips than RK3288 did not support polarity,
and register layout was different from the RK3288 PWM.
The RK3288 keep the current functions.
RK3328 and the chips after it, which can support hardware lock,
configure duty, period and polarity at next same period, to
prevent the intermediate temporary state.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Firefly ROC_RK3308_CC use ref_clock of input mode,
and rmii pins of m1 group.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3308 only support RMII mode, and if it is output clock
mode, better to use ref_clk pin with drive strength 12ma.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
serial# is one of the vendor properties and thus protected from being
overwritten if already set. If env_set is called anyway this result in
some nasty warnings, so check for presence before trying that.
In the same direction check for the presence of cpuid# and compare it
to the actual hardware and emit a warning if they don't match.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip_setup_macaddr() runs from an initcall, so returning an error
code will make that initcall fail thus breaking the boot process.
And if an ethernet address is already set this is definitly not a
cause for that, so just return success in that case.
Fixes: 0482538499 ("rockchip: rk3399: derive ethaddr from cpuid");
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some generic PX30 SoMs found in the wild use UART3 as their debug output
instead of UART2 (used for MMC) and UART5.
Make it possible to use UART3 as early debug output, with the associated
clock and pinmux configuration. Two sets of output pins are supported (M0/M1).
Future users should also note that the pinmux default in the dts is to use
the M1 pins while the Kconfig option takes M0 as a default.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
UART3 also has two sets of pins that can be selected.
Rename the config option to a common name, to allow it to be used for both
UART2 and UART3.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
According to the PX30 TRM, the iomux registers come first, before the pull
and strength control registers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
We need load some parts of ATF to sram, but rockchip
dwmmc controllers can't do dma to non-ddr addresses
space, so set the mmc controller into fifo mode in spl.
And show my best respect to Heiko's work for this solution.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds a general board file based on MT8518 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8518 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
[trini: Migrate env location to defconfig, set ENV_IS_IN_MMC]
Signeed-off-by: Tom Rini <trini@konsulko.com>
Add support for MediaTek MT8518 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
We don't have full device-tree support in SPL yet - add an appropriate
U_BOOT_DEVICE() to the board file.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This commit:
d409c96216
causes build failure with ICACHE enabled. This is due to missing
invalidate_icache_all() stub. Let's add empty invalidate_icache_all() in
the case where ICACHE is not enabled.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Move this function into the init.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move this function into init.h which seems to be designed for this sort
of thing. Also update the header to declare struct global_data so that it
can be included without global_data.h being needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these functions into the command.h header file which is a better fit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are fairly widely used in
U-Boot. But it is not clear that they will use driver model anytime soon,
so we don't want to label them as 'legacy'.
Move them to a new irq_func.h header file. Avoid the name 'irq.h' since it
is widely used in U-Boot already.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These are used by only one arch and only within a single file. Drop the
declarations from the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function has a similar name to the common wait_ticks(). It is only
used in one place and seems small enough to drop.
Inline it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in time.h so move them over and add comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
