The API is more convenient to use if one doesn't have to know upfront
which gpio controller has a line with the name one is searching for,
and arrange to look that device up somehow. Or implement this loop
oneself.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
These operations are required by dm_rtc_read and
dm_bootcount_get helpers.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The deletion process handles special case for symlinks whose target are
small enough that it fits in struct ext2_inode.b.symlink. So no block had
been allocated. But the check of file type wrongly considered regular
files as symlink. So, no block was freed. So, the EXT4 partition could be
corrupted because of no free block available.
Signed-off-by: Corentin GUILLEVIC <corentin.guillevic@smile.fr>
Do not mangle lower or mixed case filenames which fit into the upper
case 8.3 short filename. This ensures FAT standard compatible short
filenames (SFN) to support systems without long filename (LFN) support
like boot roms (ex. SFN BOOT.BIN instead of BOOT~1.BIN for LFN
boot.bin).
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Adds a test for the new pci_mps command to ensure that it can set the
Maximum Payload Size (MPS) of all devices to 256 bytes in the sandbox
environment. Enables the pci_mps command in the sandbox environment so
that this test can be run.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reports the sandbox swapcase PCI Express device to support a 256 byte
Maximum Payload Size for MPS tuning tests.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable tuning of the PCI Express MPS (Maximum Payload Size) of
each device. The Maximum Read Request Size is not altered.
The SAFE method uses the largest MPS value supported by all devices in the
system for each device. This method is the same algorithm as used by Linux
pci=pcie_bus_safe.
The PEER2PEER method sets all devices to the minimal (128 byte) MPS, which
allows hot plug of devices later that might only support the minimum size,
and ensures compatibility of DMA between two devices on the bus.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
There can certainly be a lot more elements in the "revisions" (and
"names") arrays than there are gpios used to form the trinary number
we're searching for; we simply don't know the array size up-front.
Nor do we need to, because the loop body already knows to recognize
-EOVERFLOW as "not that many elements present" (and we have a test
that specifically ensures that dev_read_u32_index() returns exactly
that). So just drop the i < priv->gpio_num condition.
While in here, fix the weird placement of the default: keyword.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Instead of calling env_get(from) up to three times, just do it once,
computing the value we will put into 'to' and error out if that is
NULL (i.e. no 'from' variable and no default provided).
No functional change.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kconfig settings that are related to the API for standalone applications
should be in the API sub-menu and not on the top level.
CONFIG_STANDALONE_LOAD_ADDR is only relevant if standalone example
applications are built.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Sort the defaults list in BUILD_TARGET Kconfig option. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case fitImage support is disabled, and image_locate_script() is
passed a fitImage, then the 'data' variable is used uninitialized.
Drop into the default: branch of the switch-case statement and do
not return the uninitialized data, and do not modify the return
pointer either, just print an error message.
Reported by clang build:
"
$ make HOSTCC=clang CC=clang KCFLAGS=-Werror sandbox64_defconfig && make HOSTCC=clang CC=clang KCFLAGS=-Werror
...
boot/image-board.c:1006:7: error: variable 'data' is used uninitialized whenever switch case is taken [-Werror,-Wsometimes-uninitialized]
case IMAGE_FORMAT_LEGACY:
^~~~~~~~~~~~~~~~~~~
include/image.h:608:29: note: expanded from macro 'IMAGE_FORMAT_LEGACY'
^~~~
boot/image-board.c:1128:19: note: uninitialized use occurs here
*datap = (char *)data;
^~~~
boot/image-board.c:1001:11: note: initialize the variable 'data' to silence this warning
u32 *data;
^
= NULL
"
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Definitions are according to the MV78460 Hardware Specifications.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM fills into bits [31:28] of register 0x182d0 tracing value,
which represents in which state BootROM currently is. BootROM fills one
of the possible values: 0x2 (CPU initialization), 0x3 (UART detection),
0x6 (UART booting), 0x8 (PCI Express booting), 0x9 (parallel or SPI NOR
booting), 0xA (parallel or SPI NAND booting), 0xB (SATA booting) and 0xE
(SD / eMMC booting).
Meaning of these values matches TRACE_* macros from Marvell soc_spec.h file:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/blob/u-boot-2013.01-armada-18.06/tools/marvell/doimage_mv/soc_spec.h
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to merge BOOT_FROM_MMC and BOOT_FROM_MMC_ALT constants to one
macro. And also allows to extend other BOOT_FROM_* macros for other
variants.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x22 as SPI-NAND. So remove
incorrect definition 0x22 as SATA. SATA on A385 has configuration 0x2A.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x3f as invalid. When booting
fails (e.g. because of invalid configuration) then BootROM fallbacks to
UART booting.
Detecting BootROM fallback to UART booting is implemented in U-Boot since
commit 2fd4284051 ("ARM: mach-mvebu: handle fall-back to UART boot").
So there is no need to define BOOT_FROM_UART_ALT constant and special
handling for it anymore, remove it.
This change effectively revers commit f3a88e2ca1 ("arm: mvebu: fix boot
from UART on ClearFog Base").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Show correct information in debug() output and use correct names for variables.
No functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[upstream of vendor commit 19a96f7c40a8fc1d0a6546ac2418d966e5840a99]
The Clearfog devices have only one SDHC device. This is either eMMC if
it is populated on the SOM or SDHC if not. The Linux device tree assumes
the SDHC case. Detect if the device is an eMMC and fixup the device-tree
so it will be detected by Linux.
Ported from vendor repo at https://github.com/SolidRun/u-boot
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This new clearfog_spi_defconfig file is a copy of existing
clearfog_defconfig file modified to instruct build system to generate
final kwbimage for SPI booting and to store the environment in SPI.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A388 Clearfog MMC is either SD Card or eMMC with different behaviour for
both. Setting the device to non-removable in the u-boot.dtsi allows both
to correctly detect the device.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move to using .env file for setting up environment variables for am65x.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Include ti_armv7_common.env and ti/mmc.env, which includes' K3 common
environment variables used across different K3 boards.
This patch depends on
https://lore.kernel.org/all/20230315052745.110502-1-n-francis@ti.com/
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TI's security enforcing SoCs will authenticate each binary it loads by
comparing it's signature with keys etched into the SoC during the boot
up process. The am62ax family of SoCs by default will have some level of
security enforcement checking. To keep things as simple as possible,
enable the CONFIG_TI_SECURE_DEVICE options by default so all levels of
secure SoCs will work out of the box
Enable the CONFIG_TI_SECURE_DEVICE by default
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Move to using .env file for setting up environment variables for J721E
and J7200.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move to using .env file for setting up environment variables for J721S2.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add K3 common environment variables to .env. We retain the old-style C
environment .h files to maintain compatibility with other K3 boards that
have not moved to using .env yet.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Last use of CONFIG_SYS_GPIO1_PRELIM was removed by
commit fae2ea5951 ("ppc: Remove MPC8349EMDS board and ARCH_MPC8349
support").
Last use of CONFIG_SYS_GPIO2_PRELIM was removed even before by
commit 6843862342 ("ppc: Remove caddy2 / vme8349 boards")
Those two items were removed from whitelist by
commit 8cca60a2cb ("Kconfig: Remove some symbols from the whitelist")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: fae2ea5951 ("ppc: Remove MPC8349EMDS board and ARCH_MPC8349 support")
Last (incorrect) use of those CONFIG items was removed by
commit 9fd9abedcc ("TQM834x: remove defines causing gcc4.4 warnings")
Those items are invalid and should have been removed at the
same time because lblaw[] has only 4 elements.
And they were removed from the whitelist by
commit 9c5df7a2a9 ("mpc83xx: Migrate LBLAW_* to Kconfig")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Fixes: 9fd9abedcc ("TQM834x: remove defines causing gcc4.4 warnings")
Apple silicon SoCs have numerous embedded co-processors with pre-loaded
firmware. The co-processors text and data sections need to be mapped via
DART iommus controlled by the main processor. Those sections are
exported as reserved-memory. Bump CONFIG_LMB_MAX_REGIONS from 8 to 64 to
deal with the large amount of reserved-memory regions.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The Linux devicetrees for Apple silicon devices are after review
feedback switching from deleting unused PCIe ports to disabling them.
Link: https://lore.kernel.org/asahi/1ea2107a-bb86-8c22-0bbc-82c453ab08ce@linaro.org/
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The WIZ acts as a wrapper for SerDes and has Lanes 0 and 2 reserved
for USB for type-C lane swap if Lane 1 and Lane 3 are linked to the
USB PHY that is integrated into the SerDes IP. The WIZ control register
has to be configured to support this lane swap feature.
The support for swapping lanes 2 and 3 is missing and therefore
add support to configure the control register to swap between
lanes 2 and 3 if PHY type is USB.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
It's possible that the Type-C plug orientation on the DIR line will be
implemented through hardware design. In that situation, there won't be
an external GPIO line available, but the driver still needs to address
this since the DT won't use the typec-dir-gpios property.
Add code to handle LN10 Type-C swap if typec-dir-gpios property is not
specified in DT.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
For non TI boards it is not possible to enable the do_board_detect()
call as TI_I2C_BOARD_DETECT is defined in board/ti/common/Kconfig.
I want to use do_board_detect() to dectect boards and properties based
on some SPI communication with a FPGA.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kconfig does not support using 'select' to select a 'choice'. A choice
can be configured by either setting the choice symbol to 'y' in a
configuration file or by setting a 'default' of the choice.
In board/ti/*/Kconfig the SOC_K3_* choice is already set to 'y' in their
corresponding configs/*_defconfig file. So remove selecting it.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
The M.2 slots of the related IOT2050 variant need to be configured
according to the plugged cards. This tries to detect the card using the
M.2 configuration pins of the B-key slot. If that fails, a U-Boot
environment variable can be set to configure manually. This variable is
write-permitted also in secure boot mode as it is not able to undermine
the integrity of the booted system.
The configuration is then applied to mux the serdes and to fix up the
device tree passed to or loaded by the bootloader. The fix-ups are
coming from device tree overlays that are embedded into the firmware
image and there also integrity protected. The OS remains free to load
a device tree to which they do not apply: U-Boot will not fail to boot
in that case.
Based on original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add support for the M.2 board based on the iot2050 advanced board.
The board has two m.2 connectors, one is B-keyed, the other E-keyed.
The B-key slot can connect 5G/SSD devices, and E-key can be used for
WIFI/BT devices.
This variant is covered by PG2 firmware image.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: align DT to kernel, polish wording]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
User-button is controlled by the mcu domain gpio number 25.
But main0 main1 mcu domain all have gpio number 25.
To identify where the gpio is from, Using gpio controll base as the prefix
to indicate the gpio resource.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use external blob otpcmd.bin to replace the 0xff filled OTP programming
command block to create a firmware image that provisions the OTP on
first boot. This otpcmd.bin is generated from the customer keys using
steps described in the meta-iot2050 integration layer for the device.
Based on original patch by Baocheng Su.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
There are many ways to get a signed firmware for the IOT2050 devices,
namely for the parts under user-control. This script documents one way
of doing it, given a signing key. Augment the board documentation with
the required procedure around it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Allows to create a public key device tree dtsi for inclusion into U-Boot
SPL and proper during first build already. This can be achieved via
CONFIG_DEVICE_TREE_INCLUDES.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add hashes and configuration signature stubs to prepare verified boot
of main U-Boot by SPL.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
