At present malloc_base/_limit/_ptr are not initialised in spl_init() when
we call spl_init() in board_init_f(). This is due to a recent change aimed
at avoiding overwriting the malloc area set up on some boards by
spl_relocate_stack_gd().
However if CONFIG_SPL_STACK_R_MALLOC_SIMPLE_LEN is not defined, we now
skip setting up the memory area in spl_init() which is obviously wrong.
To fix this, add a new function spl_early_init() which can be called in
board_init_f().
Fixes: b3d2861e (spl: Remove overwrite of relocated malloc limit)
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Rewrote spl_{,early_}init() to avoid duplicate code:
Rewrite/expand commit message:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eddie Cai <eddie.cai.linux@gmail.com>
It is useful to have a basic sanity check for EFI loader support. Add a
'bootefi hello' command which loads HelloWord.efi and runs it under U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Fix documentation, add unfulfilled kconfig dep]
Signed-off-by: Alexander Graf <agraf@suse.de>
This is used in some link scripts, so add a declaration for it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There are no files that include <asm-generic/errno.h> any more.
Move error macro defines to include/linux/errno.h and remove
include/asm-generic/errno.h.
Going forward, please include <linux/errno.h> when you need error
macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Secure_ram variable was put in generic global data. But only ARMv8
uses this variable. Move it to ARM specific data structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Setup flag when default environment are used to be able to
rewrite default distro boot variables based on SoC boot mode.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Certain GPIO devices have the capability to switch their GPIOs into
open-drain mode, that is, instead of actively driving the output
(Push-pull output), the pin is connected to the collector (for a NPN
transistor) or the drain (for a MOSFET) of a transistor, respectively.
The pin then either forms an open circuit or a connection to ground,
depending on the state of the transistor.
This patch adds functions to the GPIO uclass to switch GPIOs to
open-drain mode on devices that support it.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Many drivers use a common form of offset + flags for device
tree nodes. e.g.:
<&gpio1 2 GPIO_ACTIVE_LOW>
This patch adds a common implementation of this type of parsing
and calls it when a gpio driver doesn't supply its' own xlate
routine.
This will allow removal of the driver-specific versions in a
handful of drivers and simplify the addition of new drivers.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some functions do not change the struct gpio_desc parameter. Update these to
use const so this is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We can use GPIOs as binary digits for reading 'strapping' values. Each GPIO
is assigned a single bit and can be set high or low on the circuit board. We
already have a legacy function for reading these values. Add one that
supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Before relocation we need to reserve memory for the video driver frame
buffers so that they can use this memory when they start up (after
relocation). Add a call to the uclass to permit this.
The current top and bottom of the region is stored in global_data so that
it can be checked post-relocation to ensure enough memory is available. No
video device should be probed before relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Secure memory is at the end of memory, separated and reserved
from OS, tracked by gd->secure_ram. Secure memory can host
MMU tables, security monitor, etc. This is different from PRAM
used to reserve private memory. PRAM offers memory at the top
of u-boot memory, not necessarily the real end of memory for
systems with very large DDR. Using the end of memory simplifies
MMU setup and avoid memory fragmentation.
"bdinfo" command shows gd->secure_ram value if this memory is
marked as secured.
Signed-off-by: York Sun <yorksun@freescale.com>
It is useful to be able to record console output and provide console input
via a buffer. This provides sandbox with the ability to run a command and
check its output. If the console is set to silent then no visible output
is generated.
This also provides a means to fix the problem where tests produce unwanted
output, such as errors or warnings. This can be confusing. We can instead
set the console to silent and record this output. It can be checked later
in the test if required.
It is possible that this may prove useful for non-test situations. For
example the console output may be suppressed for normal operations, but
recorded and stored for access by the OS. That feature is not implemented
at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present in SPL we place the device tree immediately after BSS. This
avoids needing to copy it out of the way before BSS can be used. However on
some boards BSS is not placed with the image - e.g. it can be in RAM if
available.
Add an option to tell U-Boot that the device tree should be placed at the
end of the image binary (_image_binary_end) instead of at the end of BSS.
Note: A common reason to place BSS in RAM is to support the FAT filesystem.
We should update the code so that it does not use so much BSS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GENMASK is used to create a contiguous bitmask([hi:lo]).
This patch is a copy from Linux, with below commit details
"bitops: Fix shift overflow in GENMASK macros"
(sha1: 00b4d9a14125f1e51874def2b9de6092e007412d)
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.
The fix is not complicated but it seems safer to revert this for now.
This reverts commit 2afddae075.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some archs like to have larger alignment for their global data. Use 16 bytes
which suits all current archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When running U-Boot as an EFI application we cannot relocate since we do not
have relocation information. U-Boot has already been relocated to a suitable
address.
Add a global_data flag to control skipping relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a convention that the generic global_data only occupy the bottom 16 bits
of the flags word, so that there is less chance of a conflict. At present the
x86 flags conflict.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.
Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be used for testing to manually request a GPIO for use,
without resorting to the legacy GPIO API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
gpio_get_values_as_int() should return an error if something goes wrong.
Also provide gpio_claim_vector(), a function to request the GPIOs and set
them to input mode. Otherwise callers have to do this themselves.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds generic board support for MCF547X/8X and MCF5445X.
It is based on the patch about common generic board support for
M68K architecture sent by Angelo.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
this is an atempt to make the export of functions typesafe.
I replaced the jumptable void ** by a struct (jt_funcs) with function pointers.
The EXPORT_FUNC macro now has 3 fixed parameters and one
variadic parameter
The first is the name of the exported function,
the rest of the parameters are used to format a functionpointer
in the jumptable,
the EXPORT_FUNC macros are expanded three times,
1. to declare the members of the struct
2. to initialize the structmember pointers
3. to call the functions in stubs.c
Signed-off-by: Martin Dorwig <dorwig@tetronik.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(resending to the list since my tweaks are not quite trivial)
Add a deprecation notice to each function so that it is more obvious that we
are moving GPIOs to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present U-Boot sort-of supports the standard way of reading GPIOs from
device tree nodes, but the support is incomplete, a bit clunky and only
works for GPIO bindings where #gpio-cells is 2.
Add new functions to request GPIOs, taking full account of the device
tree binding. These permit requesting a GPIO with a simple call like:
gpio_request_by_name(dev, "cd-gpios", 0, &desc, GPIOD_IS_IN);
This will request the GPIO, looking at the device's node which might be
this, for example:
cd-gpios = <&gpio TEGRA_GPIO(B, 3) GPIO_ACTIVE_LOW>;
The GPIO will be set to input mode in this case and polarity will be
honoured by the GPIO calls.
It is also possible to request and free a list of GPIOs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Only the GPIO driver knows about the full GPIO device tree binding used by
a device. Add a method to allow the driver to provide this information to the
uclass, including the GPIO offset within the device and flags such as the
polarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
So far driver model's GPIO uclass just implements the existing GPIO API.
This has some limitations:
- it requires manual device tree munging to support GPIOs in device tree
(fdtdec_get_gpio() and friends)
- it does not understand polarity
- it is somewhat slower since we must scan for the GPIO device each time
- Global GPIO numbering can change if other GPIO drivers are probed
- it requires extra steps to set the GPIO direction and value
The new functions have a dm_ prefix where necessary to avoid name conflicts
but we can remove that when it is no-longer needed. The new struct gpio_desc
holds all required information about the GPIO. For now this is intended to
be stored by the client requesting the GPIO, but in future it might be
brought into the uclass in some way.
With these changes the old GPIO API still works, and uses the driver model
API underneath.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit is a preperation for a subsequent UBIFS commit
which needs atomic_long operations.
Therefor "include/asm-generic/atomic-long.h" is imported
from 1860e37 Linux 3.15
Signed-off-by: Anton Habegger <anton.habegger@gmail.com>
Introduce a gd->hose to save the pci hose in the early phase so that
apis in drivers/pci/pci.c can be used before relocation. Architecture
codes need assign a valid gd->hose in the early phase.
Some variables are declared as static so change them to be either
stack variable or global data member so that they can be used before
relocation, except the 'indent' used by CONFIG_PCI_SCAN_SHOW which
just affects some print format.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The simple malloc() implementation is used when memory is tight. It provides
a simple buffer with an incrementing pointer.
At present the implementation is inside dlmalloc. Move it into its own file
so that it is easier to find.
Rather than using relocation as a signal that the full malloc() is
available, add a special GD_FLG_FULL_MALLOC_INIT flag. This signals that the
simple malloc() should no longer be used.
In some cases, such as SPL, even the code space used by the full malloc() is
wasteful. Add a CONFIG_SYS_MALLOC_SIMPLE option to provide only the simple
malloc. In this case the full malloc is not available at all. It saves about
1KB of code space and about 0.5KB of data on Thumb 2.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
For board IDs a common approach is to set aside several GPIOs for use in
determining the board ID. This can provide information about board features
and the revision.
Add a function that turns a list of GPIOs into an integer by assigning
each GPIO to a single bit.
Signed-off-by: Simon Glass <sjg@chromium.org>
In general we can't store things in the data section until we have inited
SDRAM. Some platforms allow this (e.g. those with SPL) but some don't. Move
the pointer to global_data so that it will work on all platforms.
Without this fix the serial port will not work prior to relocation with
driver model on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
We have several GPIO drivers now and all are doing similar things to record
which GPIOs are reserved.
Move this logic into the uclass to make the drivers similar.
We retain the request()/free() methods since currently one driver does use
these for setting up the pin.
Signed-off-by: Simon Glass <sjg@chromium.org>
The GPIO list is very long in many cases and most of them are not used.
By default, show only the GPIOs that are in use, and provide a flag to show
all of them. This makes the 'gpio status' command much more pleasant.
In order to do this, driver model now exposes a method for obtaining the
'function' of a GPIO, which describes whether it is an input or output, for
example. Implementation of this method is optional.
Signed-off-by: Simon Glass <sjg@chromium.org>
For sandbox we have a fallback console which is used very early in
U-Boot, before serial drivers are available. Rather than try to guess
when to switch to the real console, add a flag so we can be sure. This
makes sure that sandbox can always output a panic() message, for example,
and avoids silent failure (which is very annoying in sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
Initialise devices marked 'pre-reloc' and make them available prior to
relocation. Note that this requires pre-reloc malloc() to be available.
Signed-off-by: Simon Glass <sjg@chromium.org>
If we are to have driver model before relocation we need to support some
way of calling memory allocation routines.
The standard malloc() is pretty complicated:
1. It uses some BSS memory for its state, and BSS is not available before
relocation
2. It supports algorithms for reducing memory fragmentation and improving
performace of free(). Before relocation we could happily just not support
free().
3. It includes about 4KB of code (Thumb 2) and 1KB of data. However since
this has been loaded anyway this is not really a problem.
The simplest way to support pre-relocation malloc() is to reserve an area
of memory and allocate it in increasing blocks as needed. This
implementation does this.
To enable it, you need to define the size of the malloc() pool as described
in the README. It will be located above the pre-relocation stack on
supported architectures.
Note that this implementation is only useful on machines which have some
memory available before dram_init() is called - this includes those that
do no DRAM init (like tegra) and those that do it in SPL (quite a few
boards). Enabling driver model preior to relocation for the rest of the
boards is left for a later exercise.
Signed-off-by: Simon Glass <sjg@chromium.org>
using UBI and DM together leads in compiler error, as
both define a "struct device", so rename "struct device"
in include/dm/device.h to "struct udevice", as we use
linux code (MTD/UBI/UBIFS some USB code,...) and cannot
change the linux "struct device"
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Before this commit, CONFIG_MPC8260 and CONFIG_8260
were used mixed-up.
All boards with mpc8260 cpu defined both of them:
- CONFIG_MPC8260 was defined in board config headers
and include/common.h
- CONFIG_8260 was defined arch/powerpc/cpu/mpc8260/config.mk
We do not need to have both of them.
This commit keeps only CONFIG_MPC8260.
This commit does:
- Delete CONFIG_8260 and CONFIG_MPC8260 definition
in config headers and include/common.h
- Rename CONFIG_8260 to CONFIG_MPC8260
in arch/powerpc/cpu/mpc8260/config.mk.
- Rename #ifdef CONFIG_8260 to #ifdef CONFIG_MPC8260
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Add driver model support for GPIOs. Since existing GPIO drivers do not use
driver model, this feature must be enabled by CONFIG_DM_GPIO. After all
GPO drivers are converted over we can perhaps remove this config.
Tests are provided for the sandbox implementation, and are a sufficient
sanity check for basic operation.
The GPIO uclass understands the concept of named banks of GPIOs, with each
GPIO device providing a single bank. Within each bank the GPIOs are numbered
using an offset from 0 to n-1. For example a bank named 'b' with 20
offsets will provide GPIOs named b0 to b19.
Anonymous GPIO banks are also supported, and are just numbered without any
prefix.
Each time a GPIO driver is added to the uclass, the GPIOs are renumbered
accordinging, so there is always a global GPIO numbering order.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Add driver model functionality for generic board.
This includes data structures and base code for registering devices and
uclasses (groups of devices with the same purpose, e.g. all I2C ports will
be in the same uclass).
The feature is enabled with CONFIG_DM.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
Signed-off-by: Viktor Křivák <viktor.krivak@gmail.com>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Many platforms duplicate pretty much the same timer code yet they all have
a 32-bit freerunning counter register. Create a common implementation that
minimally requires 2 or 3 defines to add timer support:
CONFIG_SYS_TIMER_RATE - Clock rate of the timer counter
CONFIG_SYS_TIMER_COUNTER - Address of 32-bit counter
CONFIG_SYS_TIMER_COUNTS_DOWN - Define if counter counts down
All functions are weak or ifdef'ed so they can still be overriden by any
platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.
Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h
Signed-off-by: Tom Rini <trini@ti.com>
This Patch introduce the new i2c_core file, which holds
the I2C core functions, for the rework of the multibus/
multiadapter support.
Also adds changes in i2c.h for the new I2C multibus/multiadapter
support. This new support can be activated with the
CONFIG_SYS_I2C define.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Add hooks for tracing to generic board, including:
- allow early tracing to start early as possible in U-Boot
- reserve memory for trace buffer
- copy early trace buffer to main trace buffer after relocation
- setup full tracing support after relocation
Signed-off-by: Simon Glass <sjg@chromium.org>
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This commit refactors common/board_f.c and common/board_r.c
in order to delete the dest_addr and dest_addr_sp from
gd_t struct.
As mentioned as follows in include/asm-generic/global_data.h,
/* TODO: is this the same as relocaddr, or something else? */
unsigned long dest_addr; /* Post-relocation address of U-Boot */
dest_addr is the same as relocaddr.
Likewise, dest_addr_sp is the same as start_addr_sp.
It seemed dest_addr/dest_addr_sp was used only as a scratch variable
to calculate relocaddr/start_addr_sp, respectively.
With a little refactoring, we can delete dest_addr and dest_addr_sp.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Add generic board support for sandbox. and remove the old board init code.
Select CONFIG_SYS_GENERIC_BOARD for sandbox now that this is supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
We decided to used unsigned int here, rather than unsigned long. But
for the generic global_data it is still unsigned long. So change it
over.
Signed-off-by: Simon Glass <sjg@chromium.org>
This file handles common pre-relocation init for boards which use
the generic framework.
It starts up the console, DRAM, performs relocation and then jumps
to post-relocation init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
We create a separate header file for link symbols defined by the link
scripts. It is helpful to have these all in one place and try to
make them common across architectures. Since Linux already has a similar
file, we bring this in even though many of the symbols there are not
relevant to us.
Each architecture has its own asm/sections.h where symbols specifc to
that architecture can be added. For now everything except AVR32 just
includes the generic header.
One change is needed in arch/avr32/lib/board.c to make this conversion
work.
Reviewed-by: Tom Rini <trini@ti.com> (version 5)
Signed-off-by: Simon Glass <sjg@chromium.org>
This file holds the board info structure. We need this to be generic
for the unified board series, so create a structure which contains
the basic fields required by the main architectures.
Signed-off-by: Simon Glass <sjg@chromium.org>
All the global flag defines are the same across all arches. So unify them
in one place, and add a simple way for arches to extend for their needs.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Change "int gp" to "unsigned gpio"
Add request and free entry-points
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Since we want want to have a standard GPIO interface, this adds a definition
for this into include/asm-generic/gpio.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for newer (up to 2.6.33) kernels
Add zboot command which takes the address of a bzImage as its first
argument and (optionally) the size of the bzImage as the second argument
(the second argument is needed for older kernels which do not include
the bzImage size in the header)
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
This is based on the asm-arm/unaligned.h, but made generic so all arches
that cannot do unaligned accesses can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We need signal.h for Blackfin/KGDB, so import the asm-generic/signal.h
for people to leverage.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch use blackfin errno.h implementation which
correspond Linux kernel one.
MIPS implemetation is different that's why I keep it.
I removed ppc_error_no.h from Marvell boards which
was the same too.
I have got ack from ppc40x, blackfin, arm, coldfire and avr custodians.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
