Now zynq_gem driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
phyread can timeout and val will contain random value. Initialize it to
zero not to report random value in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Functions can return NULL in case of error that's why checking return
value is needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In case of phyread()/phy_setup_op() timeout code is working with
uninitialized phyreg variable. Initialize this variable to make sure
that code it not working with random value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit_le32 returns negative value on failure. Fix phy...() to
handle these failures properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Dont enable SGMII and PCS selection if internal PCS/PMA
is not used, by getting the info about internal/external
PCS/PMA usage from dt property "is-internal-phy".
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont flush dummy descriptors as they are already
allocated from a region with dcache off. Tested
this on Zynq(zc702) and ZynqMP(zcu102) boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use wait_for_bit to be non breakable as using it with
breakable causes issue of un interruptible auto negotiation.
This is due to the ctrlc pressed will taken for wait_for_bit()
abort during phy_read() and hence not coming out of
auto negotiation.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The .read_rom_hwaddr net_ops hook does not check the return value, which
is why it was never caught that we are currently returning 0 if the
read_rom_hwaddr function return -ENOSYS and -ENOSYS otherwise.
In this case we can simplify this by just returning the result of the
function.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Move to DM clk driver
- Add clk support for zynq_sdhci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAljKWVcACgkQykllyylKDCEsgACfey0mgRaGVMLSxMMCGgJQIK70
/oYAn3raqYrJ2e2fsjb1B5WodYcDe8L5
=JYC5
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2017.05' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2017.05
- Move to DM clk driver
- Add clk support for zynq_sdhci
When the zynq_gem driver initializes the phy it sets the supported
features that the phy can support and advertise. However instead of
masking the supported features such that it limits the available
features it sets the phy to have the exact supported features of the
zynq_gem. This is problematic as it will enable features that a phy does
not have or cannot advertise.
Specifically this appears as an issue when using a phy that is only
capable of 10/100, but the zynq_gem driver will override this and try to
enable and advertise 10/100/1000.
Reported-by: Arno Steffens <star@gmx.li>
Fixes: 80243528ef ("net: gem: Fix gem driver on 1Gbps LAN")
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Tested-by: Arno Steffens <star@gmx.li>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Move the zynq to clock framework and remove unused functions as well as
the CONFIG_ZYNQ_PS_CLK_FREQ configuration.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If available use the clock framework to set the tx clock rate of the
zynq ethernet controller.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The gem[0-1]_rclk_ctrl registers control the source of the rx clock,
control and data signals and configure via ps7_init function. Don't
overwrite the register with the default value.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable and use the clock driver routine
defined in clock driver toset required
clock appropriately.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
axi_emac, emaclite and gem have the same issue with registering
multiple instances with mdio busses. mdio bus name has to be uniq but
drivers are setting up only one name for all.
Use mdio_register_seq() and pass dev->seq number to allow multiple
mdio instances registration.
Reported-by: Phani Kiran Kara <phanikiran.kara@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: u-boot
Series-cc: Phani Kiran Kara <phanikiran.kara@gmail.com>
It is confusing that mdio commands work and report phy id as
decimal value when mii is working with hex values.
For example:
ZynqMP> mdio list
gem:
21 - TI DP83867 <--> ethernet@ff0e0000
ZynqMP> mdio read ethernet@ff0e0000 0
Reading from bus gem
PHY at address 21:
0 - 0x1140
ZynqMP> mii dump 21 0
Incorrect PHY address. Range should be 0-31
...
ZynqMP> mii dump 15
0. (1140) -- PHY control register --
(8000:0000) 0.15 = 0 reset
U-Boot normally takes hex values that's why this patch is changing mdio
command to handle hex instead of changing mii command to handle decimal
values.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Correct the SGMII enable bit position to 27 instead
of 31.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Modify the nwcfg bit definitions to have 32-bit
by removing the extra nibble.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the ability to pass the phy-handle node offset
to the phy driver. This allows the phy driver
to access the DT subnode's data and parse accordingly.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
PCS auto negotaiation bit should be enabled
along with SGMII autonegotation enabled
in phy.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Return error from probe in case of invalid phy address.
This fixes the issue of uboot crash if phy is not detected.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Provide board specific option how to read MAC address from ROM.
Do it in generic way to be reusable by differnet boards.
If this is not enough board specific functions can be created.
Signed-off-by: Joe Hershberger <joe.hershberger@gmail.com> # driver part
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MDC setting depends on pclk input clocks which varies across SoC. This
driver is used by xilinx zynq and zynqmp SOC.
Input clock frequence on silicon is 125MHz where divider 64 put
frequency below 2.5MHz requires by spec (125/64=1.95).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use core to call net_process_received_packet() instead of call inside
the driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
recv function should return 0 instead of frame_len not to
proceed the same packet again in core.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Do not set interface via configs. Read information from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function was used for OF init before DM.
Remove this function as the part of move to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Enable access to MDIO before zynq_gem_init is called.
It enables read information about phy earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move phy init code out of zynq_gem_init. DM drivers are normally calling
this code from probe function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Next step to move driver to driver model. Do not use eth_device
structure. Use private structure instead.
Add iobase to private structure to store gem iobase.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add return value for phy detection algorithm to stop init function when
phy is not found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Based on spec:
"MDC must not exceed 2.5 MHz (MDC is only active during MDIO read and
write operations)"
Zynq is running on 111MHz. Current setting is 32 which is 111/32=3.47
which is above of 2.5MHz.
Using 48 divider will give us correct setting according spec
(111/48=2.31).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Using set and clear macro is incorrect because it is not overwritting
origin mdc clock division setup.
For example origin setup is 8(0b001) and new setup is 64(0b100) which
means 0b101 is setup which is 96 divider.
Using writel to rewrite all setting like for 1000Mbit/s case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Zynq has no priority queues.
ZynqMP has one priority queue and this change is required
to get ethernet working.
This patch was not needed on ep108 for uknown reason even
it should be used.
Tested on Zynq and ZynqMP.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Target is duplicating packets. IP prefetches another BD and process it
when the first one is sent. Adding one dummy BD to the chain fix the
problem with packet duplication.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
BD_SEPRN_SPACE should not have hard coded value and it will be
calculated based on the number of buffer descriptors that we
would like to use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Previous loop was completely bogus. Iterration should go just over
statistic counters.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extend comments with register offset to help with debuggging.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
MII is setup by default for all cases. The most of boards are using
RGMII but PHY drivers are not doing any specific setting that's why MII
setting was working fine. With TI DP83867 is necessary to setup
paramaters based on interface type.
Use one setting per board for it which is something what will be removed
when driver is moved to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add debug messages to phyread/write to help with PHY debug.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix below warnings happening for xilinx_zynqmp_ep_defconfig
drivers/net/zynq_gem.c: In function ‘zynq_gem_init’:
drivers/net/zynq_gem.c:330:7: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
((u32)(priv->rxbuffers) +
^
In file included from drivers/net/zynq_gem.c:19:0:
drivers/net/zynq_gem.c:336:10: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->rx_bd, ®s->rxqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_send’:
drivers/net/zynq_gem.c:399:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
writel((u32)priv->tx_bd, ®s->txqbase);
^
./arch/arm/include/asm/io.h:146:34: note: in definition of macro ‘writel’
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/net/zynq_gem.c:404:22: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->tx_bd->addr = (u32)ptr;
^
drivers/net/zynq_gem.c:409:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32) ptr;
^
drivers/net/zynq_gem.c:414:9: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
addr = (u32)priv->rxbuffers;
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_recv’:
drivers/net/zynq_gem.c:454:31: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
net_process_received_packet((u8 *)addr, frame_len);
^
drivers/net/zynq_gem.c: In function ‘zynq_gem_initialize’:
drivers/net/zynq_gem.c:533:35: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
^
drivers/net/zynq_gem.c:533:16: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
priv->rx_bd = (struct emac_bd *)((u32)bd_space + BD_SEPRN_SPACE);
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Increase the Rx Buffer descriptors to 32. This will avoid
Rx buffer descriptors overflow if more packets were received
at one shot before we process the received ones.
This fixes the issue of intermittent timeouts during tftp
on a 1Gb connection with tftp server running on windows.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Flush and invalidate the rx buffers while sending the
tx packet it self as armv8 does flush also while doing
invalidation.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the data bus width to 64-bit AMBA Databus width in config register.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add missing header.
Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.
With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
(When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO
Do not enable emio for this standard board configuration for now.
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
The whole driver used 100Mbps because of zc702 rev B.
Fix problem with not setup proper clock for gem1.
This is generic approach for clk setup.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
BDs can be correctly setup just once and init function
performs only phy autodetection and enabling RX/TX.
RX/TX are disabled in halt function.
This patch solves the problem with repeatable tftp transfers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Removing this bit causes that frame is sent only once.
(With wrap big one packet has been sent several times
which dramatically decrease throughput)
TRM: (Table 16-3: Tx Buffer Descriptor Entry)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
