Rename SPL_MTD_SUPPORT to SPL_MTD in order to match MTD. This allows using
CONFIG_IS_ENABLED to test for MTD support.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Contrary to what the help message says, this is the number of pages per
block. Calculate it automatically based on SYS_NAND_BLOCK_SIZE and
SYS_NAND_PAGE_SIZE. To better reflect its semantics, rename it to
SYS_NAND_BLOCK_PAGES.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
We like to put the SPL first so it is clear that it relates to SPL. Rename
various malloc-related options which have crept in, to stick to this
convention.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Svyatoslav Ryhel <clamor95@gmail.com>
This converts the following to Kconfig:
CONFIG_SYS_MONITOR_LEN
To do this, we set a default of 0 for everyone because there are a
number of cases where we define CONFIG_SYS_MONITOR_LEN but the only
impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN +
CONFIG_ENV_SIZE, so we must continue to allow all boards to set this
value. Update the SPL code to use 200 KB as the default raw U-Boot size
directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_SPL_MALLOC_SIZE
CONFIG_SYS_SPL_MALLOC_START
We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to
control if we have a malloc pool or not.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
Based on commit [1][2].
[1] a40d3cc845
[2] 2448e42d73
Signed-off-by: Romain Naour <romain.naour@gmail.com>
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Based on commit: 57dbf754e3
Signed-off-by: Romain Naour <romain.naour@gmail.com>
With the Kconfig options being deleted, the references to
OMAP_EHCI_PHY are useless. Remove them from the various
defconfigs.
Signed-off-by: Adam Ford <aford173@gmail.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
CONFIG_OMAP_EHCI_PHY3_RESET_GPIO
To do this, we also introduce CONFIG_HAS_CONFIG_OMAP_EHCI_PHYn_RESET_GPIO
options to get setting the GPIO number.
Signed-off-by: Tom Rini <trini@konsulko.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_DRIVERS
CONFIG_SPL_NAND_ECC
CONFIG_SPL_NAND_SIMPLE
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_ENV_OVERWRITE
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time we can now remove our legacy code and switch to
enabling DM for USB and Ethernet.
Cc: Derald D. Woods <woods.technical@gmail.com>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This converts the following to Kconfig:
CONFIG_USE_PREBOOT
CONFIG_PREBOOT
Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.
Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.
Signed-off-by: Simon Glass <sjg@chromium.org>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Switch to using the omap3-u-boot.dtsi file for needed properties.
- Remove a few SPL features to free up more SRAM space.
- Switch CONFIG_SYS_TEXT_BASE to the normal default, we don't need to
worry about X-Loader at this point anymore.
- A few related updates to SPL options as part of switching to DM SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand. This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.
Fixes: 86dfa556d9 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini <trini@konsulko.com>
