It was protected just for SPL_OS_BOOT but this function is only called when
SPL_ATF is enabled that's why change macro name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Value of shunt resistor for INA226s that monitor VCCINT and VCC_SOC power
rails are incorrect. This patch corrects those values.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
There is 2nd pca9548 mux on I2C1 bus that controls SFP0, SFP1, and QSFP1
ports. Channel 0 and 1 are connected to J287 connector for SFP0 & SFP1, and
channel 2 is connected to J288 connector for QSFP1.
Signed-off-by: Saeed Nowshadi <saeed.nowshadi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add read/write memory utilities for 16 and 32 bits. Add these
api's for both little and big endian systems similar to arm
architecture.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not source xilinx board Kconfig by other boards. These configs should be
available only when Xilinx platforms are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linking a U-Boot larger than 1MB fails with PIE enabled:
u-boot/arch/arm/cpu/armv8/start.S:71:(.text+0x3c): relocation
truncated to fit: R_AARCH64_ADR_PREL_LO21 against symbol `__rel_dyn_end'
defined in .bss_start section in u-boot.
This extends the supported range by using adrp & add to load symbols
early while starting up.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PIE requires a 4K aligned load address. If this is not met, trap
the startup sequence in a WFI loop rather than running into obscure
failures.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: André Przywara <andre.przywara@arm.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mention the requirement of 4K aligned load addresses in the
help section for the POSITION_INDEPENDENT option.
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a missing memset to acpi_create_spcr().
The other acpi_create_xxxx() functions perform a memset on their
structures, acpi_create_spcr() does not and as a result the contents of
this table are partly uninitialized (and thus random after every reset).
Fixes: b288cd9600 ("x86: acpi: Generate SPCR table")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix the tags format in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently, the calculation for the length of the DSDT table includes any
bytes that are added for alignment, but those bytes are not initialized.
This is because the DSDT length is calculated after a call to
acpi_inc_align(). Split this up into the following sequence:
* acpi_inc()
* Calculate DSDT length
* acpi_align()
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The term eMMC is used inconsistently within the FSP devicetree
bindings (e-mmc and emmc), especially for "emmc-host-max-speed"
documentation and code disagree.
Change all eMMC instances within the FSP bindings to consistently
use "emmc". The term "emmc" is already used a lot within U-Boot,
while "e-mmc" is only used in the FSP bindings.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct one typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.
Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Latest datasheet revE has removed MIMX8ML7D/5D/7C/5C parts, so
update u-boot to remove decoding and support for those parts.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix SSCG_PLL_REFCLK_SEL_x, the offset starts from 0, not 16
Reported-by: Coverity 3448860
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Coverity reported dead code, however it is FRAC_PLL_REFCLK_SEL_MASK
was wrongly set.
Reported-by: Coverity 10045172
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
According to i.MX 7Dual Applications Processor Reference Manual, Rev. 1
The target interface CCM root index ranges [0,124], so the number
should be 125.
Reported-by: Coverity 18045
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
The following bugs are fixed:
* unaligned access in br_i32_decode()
* missing restore of global data pointer in UEFI selftest
* missing restore of global data pointer on RISC-V in UEfI subsystem
* efi_var_mem_notify_exit_boot_services() should not be __efi_runtime
-----BEGIN PGP SIGNATURE-----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=BNos
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc5
The following bugs are fixed:
* unaligned access in br_i32_decode()
* missing restore of global data pointer in UEFI selftest
* missing restore of global data pointer on RISC-V in UEfI subsystem
* efi_var_mem_notify_exit_boot_services() should not be __efi_runtime
The linker sometimes creates PT_LOAD segments with length (p_filesz) zero
as described in https://man7.org/linux/man-pages/man5/elf.5.html. This
leads to build failures. We should ignore empty segments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Function set_gd() is needed in the UEFI sub-system if the global data
pointer is stored in a register.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
PLL4Q is supplying both FDCAN and LTDC. In case HDMI is in use, the
50 MHz generated from PLL4Q cannot be divided well enough to produce
accurate clock for HDMI pixel clock. Adjust it to generate 74.25 MHz
instead. The PLL4P/PLL4R are generating 99 MHz instead of 100 MHz,
which is in tolerance for the SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Gerald Baeza <gerald.baeza@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
There is no dedicated pull resistor on the AV96 UART4 (console UART)
pin. In case there is no UART adapter installed on the AV96, the line
is floating and can trigger reception of garbage characters, which in
turn can abort U-Boot autoboot. Add default pull up to mitigate this
problem.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the unnecessary inversion on the eth_env_set_enetaddr() result which
only make complex the code of setup_mac_address() and display an invalid
value in the associated pr_err.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Instead of querying SDM for FPGA configuration status through mailbox
messages, U-Boot now checks System Manager's FPGA Config status register
for FPGA configuration status before resetting bridge.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add g_dnl_get_board_bcd_device_number, the new BCD value is used by uuu to distinguish
if the SPL supports the SDPV.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Extend fastboot_set_reboot_flag arguments with reboot reason so that
it could handle different reboot cases in future.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
This function is not actually used in U-Boot. Drop it.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce USE_EARLY_BOARD_INIT option and select it by the actual users.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enabled SDIO slot 0 (south bridge) for SD card on
Espressobin board.
Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60945
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
[pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Change active-high to active-low and change DT property name from
reset-gpio to reset-gpios. This format of gpio reset is used by
pci-aardvark driver in Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
This commit fixes initialization of COMPHY on EspressoBin.
Commit 22f418935b ("phy: marvell: a3700: Use comphy_mux on Armada
37xx.") introduced usage of comphy_mux on Armada 37xx comphy driver.
The lanes are defined in comphy_a3700.c as described in functional
specification, that is:
lane 0 is SGMII1 or USB3
lane 1 is PCIe or SGMII0
lane 2 is SATA or USB3
But the DTS for EspressoBin configures PCIe on lane 0 and USB3 on
lane 1, which is wrong in the sense of the specification and doesn't
work with the comphy_mux code, which is 2 years now (the aardvark driver
causes synchronous abort in U-Boot).
It worked till the above mentioned commit, because the code for powering
up PCIe PHY doesn't work with lane number at all, and the code for
powering up USB3 PHY works differently only if USB3 is on lane 2, ie.
the check goes like:
if (lane == 2)
something
else
something else
so it does not differentiate between lanes 0 and 1.
In the future I shall post patches that remove the comphy_a3700 driver
and add comphy driver which uses calls to ATF, like Linux' driver does.
This will have the advantage of same DTS bindings as Linux', but till
this is done, we need this patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Pali Rohár <pali@kernel.org>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Update the ringacc and udma dt nodes to use the latest RM resource types
similar to the ones used in k3-j721e dt nodes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ARC is selecting TIMER which depends on DM but DM is not selected and
doesn't need to be enabled. Fix it by selecting DM for ARC architecture.
Kconfig is showing this missing dependency by:
WARNING: unmet direct dependencies detected for TIMER
Depends on [n]: DM [=n]
Selected by [y]:
- ARC [=y] && <choice>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Enable PCI memory regions in ranges property to be of multiple entry.
This helps to add support for SoC's like OcteonTX/TX2 where every
peripheral is on PCI bus.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
