Convert the two Embest boards to use DM MMC.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable OF_CONTROL and DM for gpio and pin control support
on the i.MX6D based riotboard.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
It doesn't make much sense to have two separate configs for
the riotboard so let's merge the SPL config into the main one
for less duplication.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable OF_CONTROL and DM for gpio and pin control support
on the i.MX6Q based embestmx6boards marsboard.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Convert usbarmory to OF_CONTROL and DM for gpio, pin
usb support on the i.MX53 based usbarmory.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Andrej Rosano <andrej@inversepath.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable driver model for MTD and NAND support allowing us to remove
the iomux, init, and most of the static configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable driver model support for MMC and SATA.
Note that DM_MMC requires aliases for your mmc devices so
they are added to the dts. Linux does not support enumerating mmc
devices by alias so these are not present in the Linux dts.
Note that we still need board_mmc_init() and board_mmc_getcd() for
not DM SPL to support MMC.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable dm support for USB (which also requires dm support for fixed
regulators used for vbus enable) and remove usb iomux which is no
longer needed.
We can remove the handling of otgpwr_en gpio as this is defined in
dt as usbotg vbus-supply but we need to keep the handling of
USB_HUB_RST# for boards that have a USB HUB as that isn't defined in
the dt's currently.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Once the IMX6 pinctrl driver is added UART is fully using driver mode
so we no longer need to config and initialize it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
In preparation for dm conversion convert to OF_CONTROL by adding FIT image
support and multi dtb.
Add a board_fit_config_name_match to match the dtb based off of EEPROM
model.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update hwpartition usage
Check bootbus's arguments
workaround for erratum A-011334 for fsl_esdhc driver
add pulse width detection workaround for fsl_esdhc driver
Use alias num before checking mmc index when creating device
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmBr+AgRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebnqQf/dZUk4cpj4q29icFJhAhG3wUkzKdKywWu
wOwHPIaUIetytpjwKTbkv0cUdel5Jhp9mvnJ2O5cRUZlVdgCH+lEQmFiq1O74Jf5
IwYBN74xZuP7+rno3ZxuKhjj2ixbpeg2A5R/o7gaevIgtu4vCK71qrj3y+unjnnt
Rd5BGaVzouMya0lS9cdkrzE1vmuLXs7ZJBvKdppaNda0VScJj+JP3NqooFKRKPU+
OeyblmtfL5lGOXFdY7Wfjg0pzv5L8fJxDaYDxf6iRWWG/X6RO6zV26MWAo28Ga+J
E3fuvl0mBqr1eAg3Cf17j4s9gRZv1tMtS6Mol1scIcBrldalVFA44g==
=x75X
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6apr21' of https://source.denx.de/u-boot/custodians/u-boot-dm
ENOSYS clean-up
Minor dtoc improvements
Convert CONFIG_MISC_INIT_F to Kconfig
Allow unit tests to run on any board
pylibfdt build-rule fix
Espressobin had disabled watchdog support (CONFIG_WDT) because older stable
Linux kernel versions (which are used by current stable OpenWRT and Debian
versions) do not have support for Armada 3700 watchdog driver. Therefore
they are not able to periodically kick watchdog so Espressobin enter into
boot loop.
This change enable CONFIG_WDT, CONFIG_WDT_ARMADA_37XX and CONFIG_CMD_WDT
options which add support for U-Boot 'wdt' command. And unset new
CONFIG_WATCHDOG_AUTOSTART option which cause that watchdog is not
automatically started by U-Boot during init phase, like when CONFIG_WDT
option is not set at all.
So with this change, U-Boot on Espressobin would have working 'wdt' command
which can be used from boot scripts (e.g. for enabling watchdog prior new
Linux booting kernel). But default behavior of watchdog status stays
unchanged, U-Boot does not start watchdog on Espressobin during its init
phase.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently it is not possible to boot Linux from the SD card
by default.
Make the necessary adjustments to allow it.
Reported-by: Peter Bergin <peter@berginkonsult.se>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.z@gmail.com> # imx8mn_ddr4_evk
Reviewed-by: Peng Fan <peng.fan@nxp.com>
size of malloc() pool for use before relocation is not sufficient
for ZynqMP mini u-boot with emmc configuration. Increase it to 4K.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable time command to get the elapsed time and timer commands.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add initial support for NanoPi M4B, a minor revision of
the original NanoPi M4.
Commit details of rk3399-nanopi-m4b.dts sync from Linux 5.12-rc4:
"arm64: dts: rockchip: Add NanoPi M4B board"
(sha1: c7b03115003f7f337ab165542cee37148cf30a8a)
Signed-off-by: Alexandre Vicenzi <alexandre.vicenzi@suse.com>
Reviewed-by: Kever Yang <kever.yang@rock-cihps.com>
NanoPi R4s is SBC base on Rockchip RK3399 hexa-core processor with
dual-Core Cortex-A72 and Mali-T864 GPU with 4GiB(LPDDR4) of RAM, SD card support,
including 2 gigabit ethernet(RTL8211E 1Gbps - RTL8111H 1Gbps) and 2 USB 3.0 port.
port.It also has two GPIO headers which allows further peripherals to be used.
The devicetree file is taken of the rk3399 nanopi4 Linux kernel [1].
[1] e7a0959082
Signed-off-by: xiaobo <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The path in the Linux kernel dts directory is
rockchip/rk3326-odroid-go2.dtb.
That also seems to match the FDT path set on other boards (ie:
rock64-rk3328 for example).
Signed-off-by: Roger Pau Monne <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove the unset of the EFI loader, it's possible for U-Boot to
provide a EFI environment on this board, and it's also required by
the FreeBSD loader which mandated EFI on Aarch64.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rock960 doesn't have SPI flash on-board, but the bits
get enabled by default which means when booting we get
some errors. Explicitly disable it to stop the errors.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adds the needed target option and drivers needed for correct
bringup.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This brings the actual rk3368-lion devicetree files from Linux 5.10
instead of using something separate.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the STACK_R_ADDR at 0x600000 (6MB) we're competing with
with the loading address of either u-boot or atf parts, so move
that away to 0x4000000 (64MB) similar to rk3399.
Only lion currently sets that at all but not sheep the second
rk3368 board, so just move that to the Kconfig for rk3368 similar
to rk3399 as well.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Using a non-default SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR setting makes the
resulting u-boot-rockchip.bin unbootable, as it gets stuck after SPL.
Removing the setting from the defconfig allows U-Boot to load
successfully.
Signed-off-by: Roger Pau Monné <royger@FreeBSD.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The _SUPPORT suffix is from an earlier time and interferes with use of
the CONFIG_IS_ENABLED() macro. Rename the option to drop the suffix.
Tidy up the TODO that prompted this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move sandbox_spl over to use OF_PLATDATA_INST. Create a new board to
test the case when this is not enabled, since we will be keeping that
code around for several months and want to avoid regressions.
Skip the dm_test_of_plat_dev() test since driver info is not available
for OF_PLATDATA_INST.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
