Add entry for 3732 MT/s mode of operation of the LPDDR4, in
which case the DDR PLL has to be configured in 933 MHz mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
After acking the requested frequency, should wait the ack bit clear
by DDR controller and check the DFS interrupt for next request polling.
Otherwise, the next polling of request bit will get previous value
that DDR controller have not cleared it, so a wrong request frequency
is used.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX8ULP, The dram config timing need to be saved into sram for
ddr retention when APD enter PD mode, so add this support on i.MX8ULP.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add iMX8ULP DDR initialization driver which loads the DDR timing
parameters and executes the training procedure.
When enabling IMX8ULP_DRAM_PHY_PLL_BYPASS, using PHY PLL bypass mode
to do DDR init
Signed-off-by: Ye Li <ye.li@nxp.com>
VDD SOC normal run changed to 0.85V
LPDDR4 freq0 change from 4000MTS to 2400MTS
Signed-off-by: haidong.zheng <haidong.zheng@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When doing DDR scrub, the DDR may enter into self refresh if the
selfref_en is enabled before DDR scrub. This will cause scrub
can't complete that SBRSTAT.scrub_done won't be set.
Since the selfref_en can be programmed during the course of
normal operation, move it after DDR scrub
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently checkpatch is not happy about this file:
total: 14 errors, 2 warnings, 7 checks, 359 lines checked
Improve the coding style so that it can now report:
total: 0 errors, 0 warnings, 6 checks, 360 lines checked
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add logic to automatically update umctl2's setting based
on phy training CDD value for rank to rank space issue
Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Oliver Chen <Oliver.Chen@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The 'selfref_en' should be bit'0', so correct the setting to
enable the auto self-refresh.
Reviewed-by: Jian Li <jian.li@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is no DDR_SS_GPR0 exits on i.MX8MN, so skip setting
this register on i.MX8MN.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We will generate DRAM 4000MT/s as default for i.MX8MP.
So need DRAM PLL to generate 1000Mhz clock to DDR PHY and controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In cases when the same SPL should run on boards with i.MX8MM, that
differ in DDR configuration, it is necessary to try different
parameters and check if the training done by the firmware suceeds or
not.
Therefore we return the DDR training/initialization success to the
upper layer in order to be able to retry with different settings if
necessary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Currently inside ddr_init() there is a mix of printf() and debug()
level messages.
Since this type of information is useful for debug purposes,
convert all of them to debug level for consistency.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
On, i.MX8MQ, the PLL config must be done when ddrmix
isolation is released. So move the dram pll init after
iso config done. For other i.MX8M SOC, either init pll
before or after isolation is ok.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refine the ddr init driver to make it more reusable for different
DDR type(LPDDR4, DDR4 & DDR3L). So we can reduce some redundant
code.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the ddrc Qos setting for B1 to align with B0's setting.
Correct the initial clock for dram_pll. This setting will be
overwrite before ddr phy training. Although there is no impact
on the dram init, we still need to correct it to eliminate
confusion.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Tested-by: Robby Cai <robby.cai@nxp.com>
Since the parameter of dram_pll_init is changed, update to use new.
Also remove non-existed header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With CONFIG_SPL_OF_CONTROL, the device tree will be padded to
end of the u-boot-spl-nodtb.bin, however we also put
the ddr firmware file to this location, so need to adapt
the code with SPL OF and align to 4 bytes to ease copy firmware.
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
