Early in boot it is necessary to decode the PCI device/function values for
particular peripherals in the device tree or of-platdata. This is needed
in TPL where CONFIG_PCI is not defined.
To handle this, move pci_get_devfn() into a file that is built even when
CONFIG_PCI is not defined.
Also add a function for use by of-platdata, to convert a reg property to
a pci_dev_t.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.
This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
PCI devices may be disabled in the device tree. Devices which are probed
by the device tree handle the "status" property and are skipped if
disabled. Devices which are probed by the PCI enumeration don't check
that property. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Alex Marginean <alexandru.marginean@nxp.com>
Tested-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The content of pci_rom.c is only used in a few cases. Only build and
link in these cases to avoid a global variable as gcc doesn't always
discard those when they are unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
This function can be dropped when all boards use driver model for PCI. For
now, move it into init.h with a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
In ls_pcie_ep_enable_cfg(), as part of EP setup,config ready bit
of pci controller is set, so that RC can read the config space of EP.
While setting the config ready bit, LTSSM_EN bit in same register was
also inadvertently getting cleared. This restarts the link training
between RC and EP.
Update code to just set the desired CFG_READY bit (bit 0),
while leaving the other bits unchanged.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
add DM based PCI Configuration space access support for
MPC85xx PCI Bridge. This driver is based on
arch/powerpc/cpu/mpc85xx/pci.c
In the old driver there is a fix for a hw issue on the
TARGET_MPC8555CDS and TARGET_MPC8541CDS boards. As I
have no such hardware I did not port this part.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds PCIe controller support for MT7623.
This is adapted from the Linux version.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Add a field to the PCI emulator per-device data which records which device
is being emulated. This is useful when the emulator needs to check the
device for something.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/master to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The code in swapcase can be used by other sandbox drivers. Move it into a
common place to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove inclusion of <asm/test.h> in pci_sandbox.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This parameter is needed by the PCI driver-mode interface but is always
NULL on x86. There are a number of calls to this function so it makes
sense to minimise the parameters.
Adjust the x86 function to omit the first parameter, and introduce stub
functions to handle the conversion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/next to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present this hedaer is only available on x86. To allow sandbox to use
it for testing, move it to a common location.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this fails silently which can be confusing since some devices
on the PCI bus may not work correctly. Show a message in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add a '\n' in the PCI autoconfig fail message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If PCI auto-config runs out of memory, show a few more details to help
diagnose the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: change %x to %llx to avoid build warnings on some platforms]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present U-Boot runs autoconfig in SPL but this is best left to U-Boot
proper. For TPL and SPL we can normally used fixed BARs and save code size
and time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the debugging info a little to show the result of trying to bind
a PCI device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI emulation devices are not probed before use, since they
used to be children of the device that used them, and children cannot be
probed before their parents.
Now that PCI emulation devices are attached to the root node, we can
simply probe them, and avoid using the internal function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/next to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Sandbox pci works using emulation drivers which are currently children of
the pci device:
pci-controller {
pci@1f,0 {
compatible = "pci-generic";
reg = <0xf800 0 0 0 0>;
emul@1f,0 {
compatible = "sandbox,swap-case";
};
};
};
In this case the emulation device is attached to pci device on address
f800 (device 1f, function 0) and provides the swap-case functionality.
However this is not ideal, since every device on a PCI bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
Worse, child devices cannot be probed before their parents. This forces
us to use 'find' rather than 'get' to obtain the emulator device. In fact
the emulator devices are never probed. There is code in
sandbox_pci_emul_post_probe() which tries to track when emulators are
active, but at present this does not work.
A better approach seems to be to add a separate node elsewhere in the
device tree, an 'emulation parent'. This could be given a bogus address
(such as -1) to hide the emulators away from the 'pci' command, but it
seems better to keep it at the root node to avoid such hacks.
Then we can use a phandle to point from the device to the correct
emulator, and only on sandbox. The code to find an emulator does not
interfere with normal pci operation.
Add a new UCLASS_PCI_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. Update the existing
device trees and the code for finding an emulator.
This brings PCI emulators more into line with I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 3 typos in the commit message;
encode bus number in the labels of swap_case_emul nodes;
mention commit 4345998ae9 in sandbox_pci_get_emul()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Many support functions are common between FSP1 and FSP2. Add a new header
to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove forward declarations in fsp_support.h]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Since there is now a new version of the FSP and it is incompatible with
the existing version, move the code into an fsp1 directory. This will
allow us to put FSP v2 code into an fsp2 directory.
Add a Kconfig which defines which version is in use.
Some of the code in this new fsp1/ directory is generic across both FSPv1
and FSPv2. Future patches will address this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Convert the SH7751 PCI driver to DM and add DT probing.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
The PCIe controller register address in CCSR is different
on various platforms, the current code erroneously use
the hardcoded address (0xffe240000) and stride (0x10000)
to calculate the controller's index.
Fix it by adding the related info to the driver data
structure.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The Class Code fixup method was changed from PCIe block
revision 3.0, the current fixup is only valid for the
revision 3.0 and the later ones.
So add the Class Code fixup for the block revision < 3.0.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
This can avoid build error:
The macro in brackets of the IS_ENABLED(CONFIG_FOO) is only
defined on the platforms that select the CONFIG_FOO, while
it's not defined on platforms that do not select the
CONFIG_FOO.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The non-DM version of this driver used to set BAR0 register after the
calls to pci_set_region.
I found out that for some strange reason the ath10k driver in kernel
fails to work if this is done the other way around.
I know that Linux's driver should not depend on how U-Boot does things,
but for some strange reason it does and this seems to be the simplest
solution. Fix it since it caused regressions on Omnia.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: VlaoMao <vlaomao@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This fix issue when access config from PCIe switch.
The PCIe controller need to send Type 0 config TLP if the targeting bus
matches with the secondary bus number, which is when the TLP is targeting
the immediate device on the link.
The PCIe controller send Type 1 config TLP if the targeting bus is
larger than the secondary bus, which is when the TLP is targeting the
device not immediate on the link.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Hardware return completion status non-zero when read from non exist
function in multi-function PCIe device. Return error will cause PCIe
enumeration fail.
Change it to return 0 and return value 0xffffffff when error.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Use the uclass_first_device_check and uclass_next_device_check functions
instead of uclass_first_device and uclass_next_device in pci_init. This
ensures that all PCI devices are tried to be probed. Currently if a
device fails to probe, the enumeration stops and the devices which come
after the failed device are not probed.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: VlaoMao <vlaomao@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adds dm_pci_flr API that issues a Function Level reset on a PCI-e function,
if FLR is supported.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Makes dm_pci_map_bar API available for integrated PCI devices that
support Enhanced Allocation instead of the original PCI BAR mechanism.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
commit b7598a43f2 ("[PATCH] Avoid assigning PCI resources from
zero address") only moved the bus lower address to 0x1000 if the
given bus start address is zero. The comment said 0x1000 is a
reasonable starting value, hence we'd better apply the same
adjustment when the given bus start address is below 0x1000.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DM support and support for probing the iMX PCI driver from DT.
The legacy non-DM support is retained, however shall be removed once
DM PCI is the only option remaining.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pass the driver private data around the driver as much as possible, instead
of having it as a static global variable. This is done in preparation for
the DM conversion, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The driver limits the config space base to 32bit, however it can be
64bit on 64bit iMX hardware too. Remove that limitation. This patch
has no impact on the iMX6, which is the only SoC currently supported
by this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Pull out hard-coded register base addresses into driver private
structure in preparation for DM conversion. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
Add the infrastructure for Layerscape SoCs PCIe Gen4 controller
to update device tree nodes to convey SMMU stream IDs in the
device tree.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add PCIe Gen4 driver for the NXP Layerscape SoCs. This PCIe
controller is based on the Mobiveil IP, which is compatible
with the PCI Express™ Base Specification, Revision 4.0.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bao Xiaowei <Xiaowei.Bao@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add driver for the Renesas RCar PCIe controller present on Gen3 SoCs.
The PCIe on Gen3 is used both to connect external PCIe peripherals.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_TARGET_VME8349 can replace CONFIG_VME8349. Hence, replace
CONFIG_VME8349 with CONFIG_TARGET_VME8349, and remove CONFIG_VME8349.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
When TPL is in use, U-Boot proper should support initing the VGA ROM even
though the 32-bit init portion is in SPL. Update the condition to handle
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make sure that we don't overflow the hose->regions array, otherwise we
would end up overwriting the hose->region_count field and cause mayhem
to ensue. Also print an error message when we'd be overflowing because
it indicates that there aren't enough regions available and the number
needs to be increased.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a comment to explain the use of the hardcoded value for
the number of address cells in mvebu_get_tgt_attr(). This should help to
rework this function, once CONFIG_OF_LIVE is enabled for MVEBU in
general.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This function is not used outside this file so make it static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The dm_gpio_set_value() routine sets signal logical level, with
GPIO_ACTIVE_LOW/HIGH value taken into account. Reset active value is 1
(asserted), while reset inactive value is 0 (de-asserted). Fix the reset
toggle code to set the correct reset logic value.
Reported-by: Sven Auhagen <sven.auhagen@voleatech.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
- Move Armada XP / 38x PCIe driver to DM_PCI from me
- Move Armada XP / 38x LCD driver to DM_VIDEO from me
- Add uDPU board (Armada-3720) from Vladimir
[trini: Fix warning in pci-uclass.c by removing ret from
pci_uclass_child_post_bind as it no longer calls functions with
a return code to catch.]
Signed-off-by: Tom Rini <trini@konsulko.com>II
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.
To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
This function will be used by the Marvell Armada XP/38x PCIe driver,
which is moved to DM right now. So let's extract the functionality
from pci_uclass_child_post_bind() to make it available.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Modify the RC and EP mode judge method, save the mode as a variable,
the variable will be used by other function.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
At present line_length is always calculated in video_post_probe(). But
some hardware may use a different line length, e.g. with a 1366-wide
display.
Allow the driver to set this value if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
As the PCIe specification recommend reading the Vendor ID register
to determine if a Function is present, read the Vendor ID of a
non-existent Function must not result in system error, so we'd better
make the first CFG read to Vendor ID instead of Header Type register
in the PCIe enumeration.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This introduces two new APIs dm_pci_find_next_capability() and
dm_pci_find_next_ext_capability() to get PCI capability address
and PCI express extended capability address for a given PCI device
starting from a given offset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PCI controller can have DT subnodes describing extra properties
of particular PCI devices, ie. a PHY attached to an EHCI controller
on a PCI bus. This patch parses those DT subnodes and assigns a node
to the PCI device instance, so that the driver can extract details
from that node and ie. configure the PHY using the PHY subsystem.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Only PCI device 1 and 2 is populated on the R-Car Gen2 internal
PCIe controller. Ignore all other devices. This fix prevents a
duplication of OHCI controller response on slot 0 and 1.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Most FSL PCIe controllers expects 333 MHz PCI reference clock.
This clock is derived from the CCB but in many cases the ref.
clock is not 333 MHz and a divisor needs to be configured.
This adds PEX_CCB_DIV #define which can be defined for each
type of CPU/platform.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This introduces two new APIs dm_pci_find_capability() and
dm_pci_find_ext_capability() to get PCI capability address and
PCI express extended capability address for a given PCI device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have "struct sandbox_pci_priv" in pci_sandbox driver. To avoid
confusion, rename the emul's priv to "struct sandbox_pci_emul_priv".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present all emulated sandbox pci devices must be present in the
device tree in order to be used. The real world pci uclass driver
supports pci device driver matching, and we should add such support
on sandbox too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The correct driver data comes from the matching 'id' instead of
'find_id' in pci_find_and_bind_driver().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the newly added test cases for PCI configuration access, we get:
=> ut dm pci_busdev
Test: dm_test_pci_busdev: pci.c
test/dm/pci.c:49, dm_test_pci_busdev(): SANDBOX_PCI_VENDOR_ID == vendor:
Expected 4660, got 65535
Test: dm_test_pci_busdev: pci.c (flat tree)
test/dm/pci.c:49, dm_test_pci_busdev(): SANDBOX_PCI_VENDOR_ID == vendor:
Expected 4660, got 65535
Failures: 2
The bug only shows up when bus number is not equal to zero. This is
caused by the plain find_devfn parameter is passed to function call
pci_bus_find_devfn(), inside which find_devfn is compared to devfn
in the device's pplat structure. However pplat->devfn does not carry
the bus number. Fix this by passing find_devfn with bus number masked.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The flag to control whether to scan multi-function device during
enumeration should be cleared at the beginning of each iteration
if the device's function number equals to zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently only devfn is extracted in child_post_bind(). Now that
we have the live-tree version API to look up PCI vendor and device
id from the compatible string, let's extract and save them too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If U-Boot gets used as coreboot payload all pci resources got
assigned by coreboot. If a dts without any pci ranges gets used
the dm is not able to access pci device memory. To get things
working make use of a 1:1 mapping for bus <-> phy addresses.
This change makes it possible to get the e1000 U-Boot driver
working on a sandybridge device where U-Boot is used as coreboot
payload.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed 'u-boot' in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we use U-Boot as coreboot payload with a generic dts without
any ranges specified we fail in pci pre_probe and our pci bus
is not usable.
So convert decode_regions(..) into a void function and do the simple
error handling there.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed 'u-boot' in the commit message and checkpatch warning]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, if we happen to allocate an address requiring 64 bits to a
device only supporting 32-bit BARs, the address eventually gets silently
truncated to 32 bits. Avoid this by adding a new flag to
pciauto_region_allocate() to bail out in such situations.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
All of the debug output from this file is squished to one line. Fix
it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, qemu_arm_defconfig and qemu_arm64_defconfig only work with
the 'highmem=off' parameter passed to QEMU's virt machine. The reason is
that when 'highmem' is not disabled, QEMU appends 64-bit a memory
resource to the PCI controller's regions property in DT in addition to
the 32-bit PCI memory window in low memory. And the current DT parsing
code picks the last (thus the 64-bit one) memory resource, whose address
eventually gets silently truncated to 32 bits because
CONFIG_SYS_PCI_64BIT is not set, which obviously causes PCI to break.
Avoid this problem by ignoring memory regions whose addresses are above
the 32-bit boundary when CONFIG_SYS_PCI_64BIT is not set.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce a weak tegra_pcie_board_port_reset() function by default
calling the existing tegra_pcie_port_reset() function. Additionally add
a tegra_pcie_port_index_of_port() function to retrieve the specific PCIe
port index if required. This allows overriding the PCIe port reset
functionality from board specific code as e.g. required for Apalis T30
and Apalis TK1.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Declaration of indirect PCI bridges is not compatible with DM: Both
define PCI operations, but in different ways. Hence, don't use indirect
bridges if DM is active.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add PCIe driver for Intel FPGA PCIe IP. This driver operates the PCIe IP in
rootport mode only, the EP mode is not supported. The driver is tested
with the Intel e1000e NIC driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
If video initialization fails, the "Video:" output message will be
mixed with the next console log. Change to print out such message
only when everything is OK, which improves the boot log readability.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
