U-Boot should never save the environment unasked.
This also avoids storing broken fdt_module to flash.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken ftd_file to eMMC.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Rename board_early_init_f() to board_early_init(), since this function
has nothing to do with actual board_early_init_f() as used throughout
U-Boot. The board_early_init() is function local to this board used to
configure UART and WDT pinmux. Wrap init_uart_clk() into this function
so that early UART init would be all in one place. Turn the function
into __weak one, so it could be overridden in case custom carrier board
uses different UART or needs custom IOMUX settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
If M33 handshake is successful, TPM and DSI panel MUX setting is
done by M33, no need to set them.
If handshake is failed or M33 is not booted, continue the TPM
and DSI panel MUX setting
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update DDR PHY settings to support LPDDR4 mode only by adjusting
DQ VREF ctrl, ODT and pads drive strength.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Found the lposc fuse loading having impact to cpu idle in kernel.
Without the loading in dual boot mode, kernel will hang after idle
for a while.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This workaround is not needed on i.MX8ULP proto-1B EVK as board has
fixed the problem. Because we don't support proto-1A any longer,
remove the PMIC settings.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.
Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
DM is not used for the SPL and a generic DT is used in the SPL
which requires no fixups. Remove the call in the SPL and move the function
into the U-Boot code.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since DM_SERIAL is used for U-Boot we no longer need legacy UART code in
common.c shared by the SPL and U-Boot. Move the legacy UART config to
the non-DM SPL.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
convert to DM_I2C for U-Boot while leaving SPL legacy I2C:
- Move I2C config from common to SPL
- Move PMIC config from common to SPL (no need to re-configure pmic)
- add DM_I2C support to eeprom/gsc functions shared by SPL and U-Boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Ethernet controller and PHY use the device tree info to
configure themselves, so it's not necessary to manually do it
in the board file. This permits the removal of a bunch of headers
as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <festevam@gmail.com>
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
We use 'DEBUG' and not 'CONFIG_DEBUG' tree-wide for debug code that is
left in, and not wrapped by some other regular debugging type print
macro.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Let CONFIG_TARGET_QEMU_VIRT imply CONFIG_CMD_SBI.
The sbi command provides detailed information about the SBI.
It is useful to test the discovery of extensions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Call into k3-ddrss driver to fixup device tree and resize the available
amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup as done from
R5 SPL and apply it to DT passed to A53 U-boot, which in turn passes
this to the OS.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Use the appropriate fdtdec_setup_mem_size_base and
fdtdec_setup_bank_size calls in dram_init and dram_bank_init to pull
these values from DT, where they are already available, instead of
hardcoding them.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Now that mkimage can generate TOC0 images, and the SPL can interpret
them, hook up the build infrastructure so the user can choose which
image type to build. Since the absolute load address is stored in the
TOC0 header, that information must be passed to mkimage.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
/LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
yoje
=SwGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
Use the semihosting_enabled function to determine whether or not to
enable semihosting devices. This allows for graceful fallback in the
event a debugger is not attached.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
So far the DRAM size for both the Juno and the FVP model were hardcoded
in our config header file. For the Juno this is fine, as all models have
8 GiB of DRAM, but the DRAM size can be configured on the model command
line.
Drop the fixed DRAM size setup, instead look up the size in the device
tree, that we now have for every board. This allows a user to inject
a DT with the proper size, and be able to use the full amount of DRAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The defconfigs for the Arm Juno board and the FVP model are quite large,
setting a lot of platform-fixed variables like SYS_TEXT_BASE.
As those values are not really a user choice, let's provide default
values for them in our Kconfig file, so a lot of cruft can be removed
from the defconfig files.
This also moves the driver selection out of there, since this is again
not something a user should really decide on. Instead we allow users to
enable or disable subsystems, and select the appropriate drivers based
on that in the Kconfig file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
