Pine64 Quartz64 boards DT reference SCLK_GMAC1_RGMII_SPEED in the
assigned-clocks property of the gmac1 node. This result in a ENOENT
error when driver core tries to set a parent for this clock.
The clock speed in rgmii/rmii mode is changed using clk_set_rate of the
tx_rx clock and not using clk_set_parent of the speed clock.
Add dummy support for SCLK_GMAC1_RGMII_SPEED and similar clocks to clk
driver to allow a driver for gmac node to probe.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The clock driver for RK3568 does not include support for UART clocks in
SPL. This result in the following message with high enough loglevel.
ns16550_serial serial@fe660000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Fix this by including support for UART clocks in SPL.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The field for clk_cpll_div_25m_div in CRU_CLKSEL_CON81 is 6 bits wide,
not 5 bits wide as currently defined in CPLL_25M_DIV_MASK.
Fix this and the assert so that CPLL_25M can be assigned a 25 MHz rate.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix use of wrong clk selection for CLK_PWM1 on RK3568.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A RK3568 device tree pmic node can reference the I2S1_MCLKOUT_TX clock
in assigned-clocks, add dummy support to set parent of this clock to the
rk3568 cru driver.
Fixes probe of pmic driver and missing regulators on affected boards,
rk3568-evb and rk3568-rock-3a.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Device tree contains assigned-clock-rates property for these,
but default value will work just fine
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
SDHCI driver may attempt to set 26MHz clock, but clk_rk3568
will return error in this case. Apparently, SDHCI silently ignores the
error and as a result eMMC initialization fails.
Add 25 MHz and 26 MHz clk rates for sdmmc and emmc on rk3568 to fix that.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fix up ppll init freq.
support tclk_emmc.
add freq (26M) for mmc device.
fix up the sfc clk rate unit error.
Change in V2:
remove change id.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
