Commit graph

13 commits

Author SHA1 Message Date
Tim Harvey
fd10b3b176 imx: ventana: skip nand init for nandless boards
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15 22:01:15 +01:00
Tim Harvey
3f0da8748a imx: ventana: remove setup of I2C3 from SPL
Do not setup I2C3 in the SPL for Ventana as some devices on that bus
(aic3x codecs) can hang the bus causing i2c_setup to spin endlessly until
they are put into reset. Removing the setup of I2C3 from the SPL allows
the board-specific GPIO to be configured to take care of putting codecs
in reset prior to U-Boot setting up I2C3.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2019-02-15 22:01:15 +01:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tim Harvey
8d1a6ff825 imx: ventana: add GW5904 support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2017-03-20 19:10:22 +01:00
Tim Harvey
f3a8546b8f imx: ventana: make SD3_VSELECT board specific
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19 17:30:07 +01:00
Tim Harvey
f938500f2c imx: ventana: make OTG VBUS power enable board specific
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-19 17:30:03 +01:00
Tim Harvey
1800ffa83e imx: ventana: make number of digital I/O's dynamic
Replace the static list of board-specific digital I/O's with a dynamic list.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-07-28 13:27:18 +02:00
Tim Harvey
e49621b357 imx: ventana: make RS232 enable board specific
Not all Ventana boards have an RS232 transceiver, make it board specific.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-07-28 13:27:17 +02:00
Tim Harvey
34b080b79c imx: ventana: add fdt fixup to enable UHS-I support on selected boards
UHS-I support is available on Ventana boards with micro-SD sockets depending
on the board revision. For backwards compatibility to not break users
who have old bootloaders and newer kernels the device-tree on boards with
microSD disables UHS-I support by default by defining the no-1-8-v property
in the esdhc controller node. For models/revisions that support switchable
1.8V/3.3V I/O which is detectable by the presence of a pull-down on the
SD3_VSELECT pin we remove that property to enable support in the kernel.

Additionally we add SD3_VSELECT to the pinmux for clarity (even though U-Boot
does not currently support UHS-I modes requiring 1.8V I/O).

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-05-31 17:26:27 +02:00
Tim Harvey
5c55572ff7 imx: ventana: remove dependence on EECONFIG_SATA eeprom feature bit
The MSATA feature is a board-specific feature on Gateworks Ventana boards.

In most cases a 2:1 mux will steer either PCIe or SATA to a miniPCIe socket
through an MSATA_EN gpio. In these such cases assign the gpio in the board
specific struct and use its presence to determine if we default the GPIO to
PCIe and if we later steer it according to hwconfig.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2016-05-31 17:25:47 +02:00
Tim Harvey
9a83a81545 imx: ventana: various board-specific GPIO config updates
- Added iomux for CAN_STBY and RS484_TEN (GW52xx/GW53xx/GW54xx/GW551x)
- Moved iomux of USBHUB_RST# out of board_ehci_hcd_init so that it is
  done regardless of USB being initialized in bootloader
- Added usb_sel iomux/hwconfig for GW552x
- Fixed mezzanine DIO for GW54xx
- Fixed PANLEDR# for GW54xx
- Fixed dio iomux/hwconfig for GW552x
- Fixed dio iomux for GW551x
- removed redundant #define

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-06-01 09:48:23 +02:00
Tim Harvey
6d38f3a85d imx: ventana: detect pmic using i2c probe instead of board model
Avoid requiring board-model and probe pmic by its i2c address.
This is in preparation for being able to call pmic_setup() from SPL
and not need board type.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-05-15 19:21:25 +02:00
Tim Harvey
e56c5791af imx: ventana: split out common functions between SPL and uboot
Move shared functions used by both SPL and U-Boot to common.c:
 - setup_iomux_uart() and uart pad config
 - gpio pad config

In the process also moved the following to common.c in preparation for
calling it from the SPL:
 - split i2c setup into a shared function
 - move pmic init to setup_pmic() function to call directly from
   power_init_board()
 - split gpio setup into early (iomux and default pin config)
   and late (output configuration based on env)

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2015-05-15 19:21:25 +02:00