I2C bus 0 was not initialized correctly. There is an offset between i2c
index and the structure number of pad info. So i2c bus 0 can be in an
inconsistent state.
This problem become visible on B{4,6}50v3 with the CPUC HW watchdog enabled.
Sometimes when the CPUC HW watchdog interrupted the boot process, U-Boot was
not able to read VPD from I2C/EEPROM and the system failed to boot up again,
because a device connected to that bus was stuck in data transfer state (from
previous boot attempt) and there was no method to recover (struct
mxc_i2c_bus::idle_bus_fn was not set) courtesy of incorrect initialization.
Signed-off-by: Dan Cimpoca <dan.I.cimpoca@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
The b{4,6}50v3 kernel framebuffer console requires a modeline otherwise
the LVDS panel shows garbage.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Use Video PLL to provide 65MHz for all displays.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
While using ./scripts/get_maintainer.pl I detect that the Maintainer name
and address for bx50v3 boards are not valid.
The new maintainer for GE bx50v3 products must be Ian Ray.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Add Menlosystems M53 board, based on the M53 SoM.
This board has Ethernet, USB host, USB gadget, UART and LCD on it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Rather than passing a hardcoded maxsize to the generic get_ram_size()
function use the i.MX 7 specific imx_ddr_size() function, which extracts
the memory size at runtime by reading the DDR controller registers.
This is a purely cosmetic change as the generic get_ram_size() function
already took care of properly automatically detecting 256MB, 512MB or 1GB
modules.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
USB OTG2 port is connected to the USB host connector.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
[1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit
[2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XRFI
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Signed-off-by: Adam Ford <aford173@gmail.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On beaglebone black, it can so happen that PHY address
is not latched correctly on reset and board boots with
PHY responding to a different address than that
programmed in device-tree. For example, see this report:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Workaround this by fixing up device-tree passed to kernel
by using the PHY address detected in hardware.
Beaglebone itself uses only one ethernet port and its DT
currently uses phy_id (obsoleted). But the function has
been written to handle multiple ports and phy_id as well
as phy-handle to make the function more generically useful.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable USB gadget support using DWC2 driver
Populate board_usb_init() to initialize clocks,
phy, reset and data needed for DWC2 IP.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM
and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage.
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM
and 32 MiB of flash (SPI NOR).
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro name CONFIG_WDT_ARMADA_3720 is called CONFIG_WDT_ARMADA_37XX
instead. Fix this so that watchdog really is enabled in board_init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds a new defconfig which pre-selects the PICO-Pi baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
