AM64 as CPSW3G IP with 2 external ports. Add DT entries for the same
(based on kernel DT).
Disable second port as its by default set to ICSS usage on EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Currently driver may end up caching disabled port ID as active
interface. Fix this by bailing out earlier in case port is marked
disabled in the DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CPSW NUSS IP on K3 SoCs can have more than one external port (upto 8)
Therefore increase AM65_CPSW_CPSWNU_MAX_PORTS to 9 (8 ext + 1 Root port)
as preparation to allow any one of the 8 ports to be used as ethernet
interface in U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
ICSSG Ethernet driver uses two src threads per port (one per slice).
Similarly CPSW uses one src thread.
Drop PSIL EP static data for other src threads in order to reduce
R5 SPL footprint. This makes AM65x board bootable again.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.
There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Parse MAC addresses from EEPROM and set them in the env. This is needed
to get MAC address for additional ethernet ports on the EVM.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable all relevant configs for building multiple dtbs into a single fit
image and load the right dtb for next stage.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable relevant configs that checks for the size of image and stack:
BSS: 4KB
Initial MALLOC: 512KB
Initial Stack: 8K
SPL Image size can be: ~960KB
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM642 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM642 SoC. It supports the following interfaces:
* 2 GB LPDDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in switch and MAC mode
* x1 USB 3.0 Type-A port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x2 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin Raspberry Pi compatible GPIO header
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 54-pin header for Programmable Realtime Unit (PRU) IO pins
* Interface for remote automation. Includes:
* power measurement and reset control
* boot mode change
Add basic support for AM642 SK.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that single defconfig can be used for booting AM64 EVM and SK,
default device tree will not work for selecting dtb for kernel.
Update the env to select right dtb based on eeprom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Current BSS allocation of SPL is as below:
size spl/u-boot-spl
text data bss dec hex filename
144572 5484 1752 151808 25100 spl/u-boot-spl
But 20KB is allocated currently for BSS. Reduce it to 4KB and
save some space for stack.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable support for selecting DTB within SPL based on EEPROM.
This will help to use single defconfig for both EVM and SK
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
I2C EEPROM data contains the board name and its revision.
Add support for:
- Reading EEPROM data and store a copy at end of SRAM
- Updating env variable with relevant board info
- Printing board info during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support for
triggering DDR initialization from board_init_f().
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce ddr node for am642 needed for all ddr configurations.
Also, introduce the 1600MTs DDR4 configuration that is supported on the
am642-evm.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Attempt to get and enable a vtt regulator if one is provided from the
dts. If we do not find one, continue as not all platforms have this.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce support for the AM64 DDRSS controller which uses the 16bit
variation of the controller. This controller shares much functionality
with the existing J721e support, so this patch introduces only the new
code needed for am64 specific support from "_16bit_" files with headers
under "16bit/" include path/.
Also add a CONFIG_K3_AM64_DDRSS option to the choice required for use
with CONFIG_K3_DDRSS to allow selecting AM64 support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce a new version of the ddr driver which has the ability to
support different variations of the controller. Also introduce support
for the 32bit variation of the controller which is what was already
supported by the previous version used for J721e and J7200.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Create a new CONFIG_K3_DDRSS option to select the common parts of the
k3-ddrss driver. Also introduce a choice that depends on the top level
option to select CONFIG_K3_J721E_DDRSS for j721e support, and update
corresponding Kconfig as required.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Rename the k3-j721e folder under drivers/ram to k3-ddrss in preparation
of introducing additional support for other platforms to the same
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
