Commit graph

182 commits

Author SHA1 Message Date
Vignesh R
8c927809ea mtd: spi: spi-nor-core: Add back U-Boot specific features
For legacy reasons, we will have to keep around U-Boot specific
SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Vignesh R
7aeedac015 mtd: spi: Port SPI NOR framework from Linux
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not
support 4 byte addressing opcodes, SFDP table parsing and different types of
quad mode enable sequences. Many newer flashes no longer support BANK
registers used by sf layer to a access >16MB of flash address space.
So, sync SPI NOR framework from Linux v4.19 that supports all the
above features. Start with basic sync up that brings in basic framework
subsequent commits will bring in more features.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Boris Brezillon
4a5594fa20 mtd: Don't stop MTD partition creation when it fails on one device
MTD partition creation code is a bit tricky. It tries to figure out
when things have changed (either MTD dev list or mtdparts/mtdids vars)
and when that happens it first deletes all the partitions that had been
previously created and then creates the new ones based on the new
mtdparts/mtdids values.
But before deleting the old partitions, it ensures that none of the
currently registered parts are being used and bails out when that's
not the case. So, we end up in a situation where, if at least one MTD
dev has one of its partitions used by someone (UBI for instance), the
partitions update logic no longer works for other devs.

Rework the code to relax the logic and allow updates of MTD parts on
devices that are not being used (we still refuse to updates parts on
devices who have at least one of their partitions used by someone).

Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
a02820fca9 mtd: Delete partitions attached to the device when a device is deleted
If we don't do that, partitions might still be exposed while the
underlying device is gone.

Fixes: 2a74930da5 ("mtd: mtdpart: implement proper partition handling")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Boris Brezillon
4c47fd0b6b mtd: Add a function to report when the MTD dev list has been updated
We need to parse mtdparts/mtids again everytime a device has been
added/removed from the MTD list, but there's currently no way to know
when such an update has been done.

Add an ->updated field to the idr struct that we set to true every time
a device is added/removed and expose a function returning the value
of this field and resetting it to false.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Heiko Schocher <hs@denx.de>
2018-12-06 00:45:36 +05:30
Stefan Roese
9e5c2a755a mtd: nand: spi: Add Gigadevice SPI NAND support
This patch adds support for Gigadevices SPI NAND device to the new SPI
NAND infrastructure in U-Boot. Currently only the 128MiB GD5F1GQ4UC
device is supported.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Jagan Teki <jagan@openedev.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-10-04 18:24:24 +05:30
Miquel Raynal
2a74930da5 mtd: mtdpart: implement proper partition handling
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).

By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:32 +05:30
Miquel Raynal
ff4afa8a98 mtd: uboot: search for an equivalent MTD name with the mtdids
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.

Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:32 +05:30
Miquel Raynal
21cc1fb5af mtd: mtdpart: add a generic mtdparts-like parser
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.

This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:31 +05:30
Boris Brezillon
6f041ccabb mtd: spinand: Add initial support for the MX35LF1GE4AB chip
Add minimal support for the MX35LF1GE4AB SPI NAND chip.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Frieder Schrempf
3181c0a622 mtd: spinand: Add initial support for Winbond W25M02GV
Add support for the W25M02GV chip.

Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Peter Pan
883d8778ae mtd: spinand: Add initial support for Micron MT29F2G01ABAGD
Add a basic driver for Micron SPI NANDs. Only one device is supported
right now, but the driver will be extended to support more devices
afterwards.

Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Peter Pan
0a6d6bae03 mtd: nand: Add core infrastructure to support SPI NANDs
Add a SPI NAND framework based on the generic NAND framework and the
spi-mem infrastructure.

In its current state, this framework supports the following features:

- single/dual/quad IO modes
- on-die ECC

Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Boris Brezillon
f86787280b mtd: nand: Pass mode information to nand_page_io_req
The NAND sub-layers are likely to need the MTD_OPS_XXX mode information
in order to decide if they should enable/disable ECC or how they should
place the OOB bytes in the provided OOB buffer.

Add a field to nand_page_io_req to pass this information.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Boris Brezillon
b95db8d33a mtd: nand: Add core infrastructure to deal with NAND devices
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
d02f1d36ec mtd: move definitions to enlarge their range
Some helpers might be useful in a future 'mtd' U-Boot command to parse
MTD device list.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Brian Norris
9bfc3fde9c mtd: add get/set of_node/flash_node helpers
We are going to begin using the mtd->dev.of_node field for MTD device
nodes, so let's add helpers for it. Also, we'll be making some
conversions on spi_nor (and nand_chip eventually) too, so get that ready
with their own helpers.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-09-20 20:10:49 +05:30
Ezequiel Garcia
5f50d82d89 mtd: Uninline mtd_write_oob and move it to mtdcore.c
There's no reason for having mtd_write_oob inlined in mtd.h header.
Move it to mtdcore.c where it belongs.

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-09-20 20:10:49 +05:30
Miquel Raynal
980f65dc6c mtd: remove stale comment in mtd_oob_ops structure
A comment in the kernel doc of the mtd_oob_ops structure tells that it
is not possible to write more than one page with OOB. This was
probably true at some time in the past but today it is entirely wrong.

As one can see for instance in the nand_do_write_ops() helper available
in the NAND core, this implementation called by mtd->_write_oob()
simply loops over the pages until everything has been written.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
2018-07-24 09:25:23 -04:00
Rafał Miłecki
323a73adc9 mtd: nand: add new enum for storing ECC algorithm
Our nand_ecc_modes_t is already a bit abused by value NAND_ECC_SOFT_BCH.
This enum should store ECC mode only and putting algorithm details there
is a bad idea. It would result in too many values impossible to support
in a sane way.

To solve this problem let's add a new enum. We'll have to modify all
drivers to set it properly but once it's done it'll be possible to drop
NAND_ECC_SOFT_BCH. That will result in a cleaner design and more
possibilities like setting ECC algorithm for hardware ECC mode.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b0fcd8ab7b3c89b5da7fff5224d06ed73e7a33cc]
[Philippe Reynes: adapt code to u-boot]
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-07-23 14:33:21 -04:00
Jörg Krause
da37d09682 mtd: nand: export nand_get_flash_type function
`nand_get_flash_type()` allows identification of supported NAND flashs.
The function is useful in SPL (like mxs_nand_spl.c) to lookup for a NAND
flash (which does not support ONFi) instead of using nand_simple.c and
hard-coding all required NAND parameters.

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
2018-06-27 12:20:55 +02:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Masahiro Yamada
ba8c9ea38a mtd: nand: include <asm/cache.h> from include/linux/mtd/rawnand.h
This is needed for ARCH_DMA_MINALIGN.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-04 22:00:01 +09:00
Masahiro Yamada
6ae3900a86 mtd: nand: Rename nand.h into rawnand.h
This header was renamed to rawnand.h in Linux.

The following is the corresponding commit in Linux.

  commit d4092d76a4a4e57b65910899948a83cc8646c5a5
  Author: Boris Brezillon <boris.brezillon@free-electrons.com>
  Date:   Fri Aug 4 17:29:10 2017 +0200

      mtd: nand: Rename nand.h into rawnand.h

      We are planning to share more code between different NAND based
      devices (SPI NAND, OneNAND and raw NANDs), but before doing that
      we need to move the existing include/linux/mtd/nand.h file into
      include/linux/mtd/rawnand.h so we can later create a nand.h header
      containing all common structure and function prototypes.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-12-04 22:00:00 +09:00
Masahiro Yamada
e6001371d1 mtd: nand: introduce NAND_ROW_ADDR_3 flag
Several drivers check ->chipsize to see if the third row address cycle
is needed.  Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up.  Since
nand_scan_ident() knows well about the device, it can handle this
properly.  The flag is set if the row address bit width is greater
than 16.

Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

[Linux commit: 14157f861437ebe2d624b0a845b91bbdf8ca9a2d]
2017-11-29 00:28:59 +09:00
Masahiro Yamada
a01549ba40 mtd: nand: add a shorthand to generate nand_ecc_caps structure
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).

So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.

It allows to describe like ...

NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);

... instead of

static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
        .stepsize = 512,
        .strengths = denali_pci_ecc_strengths,
        .nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
        .stepinfos = &denali_pci_ecc_stepinfo,
        .nstepinfos = 1,
        .calc_ecc_bytes = denali_calc_ecc_bytes,
};

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

[Linux commit: a03c60178c181767ecfb26fb311a88742d228118]
2017-11-29 00:28:59 +09:00
Masahiro Yamada
470c29d1c2 mtd: nand: add generic helpers to check, match, maximize ECC settings
Driver are responsible for setting up ECC parameters correctly.
Those include:
  - Check if ECC parameters specified (usually by DT) are valid
  - Meet the chip's ECC requirement
  - Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set

The logic can be generalized by factoring out common code.

This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength

To use the helpers above, a driver needs to provide:
  - Data array of supported ECC step size and strength
  - A hook that calculates ECC bytes from the combination of
    step_size and strength.

By using those helpers, code duplication among drivers will be
reduced.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

[Linux commit: 2c8f8afa7f92acb07641bf95b940d384ed1d0294]
2017-11-29 00:28:59 +09:00
Boris Brezillon
52cde35b96 mtd: nand: Pass the CS line to ->setup_data_interface()
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 104e442a67cfba4d0cc982384761befb917fb6a1]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:59 +09:00
Masahiro Yamada
436fb2b84d mtd: nand: allow drivers to request minimum alignment for passed buffer
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf.  Drivers using DMA will be unhappy about unaligned
buffer.

The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer.  If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

[Linux commit: 477544c62a84d3bacd9f90ba75ffc16c04d78071]
2017-11-29 00:28:59 +09:00
Boris Brezillon
94b50a8aae mtd: nand: Drop the ->errstat() hook
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 7d135bcced20be2b50128432c5426a7278ec4f6d]
[masahiro: modify davinci_nand.c for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Boris Brezillon
4d75596e6d mtd: nand: Drop unused cached programming support
Cached programming is always skipped, so drop the associated code until
we decide to really support it.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 0b4773fd1649e0d418275557723a7ef54f769dc9]
[masahiro: modify davinci_nand.c for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Boris Brezillon
13f3b04f61 mtd: add mtd_ooblayout_xxx() helper functions
In order to make the ecclayout definition completely dynamic we need to
rework the way the OOB layout are defined and iterated.

Create a few mtd_ooblayout_xxx() helpers to ease OOB bytes manipulation
and hide ecclayout internals to their users.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 75eb2cec251fda33c9bb716ecc372819abb9278a]
[masahiro:
 cherry-pick more code from adbbc3bc827eb1f43a932d783f09ba55c8ec8379]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Marc Gonzalez
1fb87de83d mtd: nand: Support controllers with custom page
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 3371d663bb4579f1b2003a92162edd6d90edd089]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Boris Brezillon
6f84b26b53 mtd: nand: Add a few more timings to nand_sdr_timings
Add the tR_max, tBERS_max, tPROG_max and tCCS_min timings to the
nand_sdr_timings struct.
Assign default/safe values for the statically defined timings, and
extract them from the ONFI parameter table if the NAND is ONFI
compliant.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 204e7ecd47e26cc12d9e8e8a7e7a2eeb9573f0ba
 Fixup commit: 6d29231000bbe0fb9e4893a9c68151ffdd3b5469]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Boris Brezillon
3d841b3214 mtd: nand: Fix data interface configuration logic
When changing from one data interface setting to another, one has to
ensure a specific sequence which is described in the ONFI spec.

One of these constraints is that the CE line has go high after a reset
before a command can be sent with the new data interface setting, which
is not guaranteed by the current implementation.

Rework the nand_reset() function and all the call sites to make sure the
CE line is asserted and released when required.

Also make sure to actually apply the new data interface setting on the
first die.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 73f907fd5fa56b0066d199bdd7126bbd04f6cd7b]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Boris Brezillon
27c4792cd2 mtd: nand: automate NAND timings selection
The NAND framework provides several helpers to query timing modes supported
by a NAND chip, but this implies that all NAND controller drivers have
to implement the same timings selection dance. Also currently NAND
devices can be resetted at arbitrary places which also resets the timing
for ONFI chips to timing mode 0.

Provide a common logic to select the best timings based on ONFI or
->onfi_timing_mode_default information. Hook this into nand_reset()
to make sure the new timing is applied each time during a reset.

NAND controller willing to support timings adjustment should just
implement the ->setup_data_interface() method.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[Linux commit: d8e725dd831186a3595036b2b1df9f68cbc6efa3]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Sascha Hauer
b893e83330 mtd: nand: Expose data interface for ONFI mode 0
The nand layer will need ONFI mode 0 to use it as timing mode
before and right after reset.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 6e1f9708dbf3c50a8da93c1952a01a7a2acb5e66]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Sascha Hauer
46deff57da mtd: nand: convert ONFI mode into data interface
struct nand_data_interface is the designated type to pass to
the NAND drivers to configure the timing. To simplify further
patches convert the onfi_sdr_timings array from type struct
nand_sdr_timings nand_data_interface.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b1dd3ca203fccd111926c3f6ac59bf903ec62b05]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:58 +09:00
Sascha Hauer
01042499b8 mtd: nand: Introduce nand_data_interface
Currently we have no data structure to fully describe a NAND timing.
We only have struct nand_sdr_timings for NAND timings in SDR mode,
but nothing for DDR mode and also no container to store both types
of timing.
This patch adds struct nand_data_interface which stores the timing
type and a union of different timings. This can be used to pass to
drivers in order to configure the timing.
Add kerneldoc for struct nand_sdr_timings while touching it anyway.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: eee64b700e26b9bcc6fce024681c31f5e12271fc]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Sascha Hauer
1728eb577d mtd: nand: Create a NAND reset function
When NAND devices are resetted some initialization may have to be done,
like for example they have to be configured for the timing mode that
shall be used. To get a common place where this initialization can be
implemented create a nand_reset() function. This currently only issues
a NAND_CMD_RESET to the NAND device. The places issuing this command
manually are replaced with a call to nand_reset().

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 2f94abfe35b210e7711af9202a3dcfc9e779219a]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Sascha Hauer
6a1ff76ed3 mtd: nand: remove unnecessary 'extern' from function declarations
'extern' is not necessary for function declarations. To prevent
people from adding the keyword to new declarations remove the
existing ones.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 79022591839f110f465cac0223e117b91d47d5db]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Boris Brezillon
19d30ded88 mtd: nand: Add an option to maximize the ECC strength
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.

In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).

Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Linux commit: ba78ee00e1ff84de9b3ad33edbd3ec599099ee82]
[masahiro: of_property_read_bool -> fdt_getprop for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Masahiro Yamada
4c61f79b5e mtd: nand: add onfi_* stubs in case ONFI_DETECTION is disabled
Add stubs to the header in case CONFIG_SYS_NAND_ONFI_DETECTION is
disabled.  This is much easier than adding around #ifdef to the
caller side.

Also, I removed the #ifdef around onfi_params.  In Linux, onfi_params
and jedec_params are unified as union.  It will be the right thing
to do.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-11-29 00:28:57 +09:00
Masahiro Yamada
8b7f4b9cc1 mtd: remove MTDDEBUG() and CONFIG_MTD_DEBUG
All users of this macro have been converted.  Remove MTDDEBUG and
related CONFIG options.

ubifs_dbg_msg_key() is kept.  It is silent unless DEBUG is defined.

I am not touching scripts/config_whitelist.txt.  The deprecated options
will be dropped by the next resync.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-10-23 14:07:26 -04:00
Masahiro Yamada
b44b30260f printk: collect printk stuff into <linux/printk.h> with loglevel support
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*().  U-Boot does not support them in a clean
way.  So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.

We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround.  Hence this
patch, to find the best home for all printk variants.  If you want to
use printk() and friends, please include <linux/printk.h>.  This header
is self-contained, and pulls in only a few headers.

When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards.  This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.

To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel".  (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.

The difference is the loglevel is build-time determined.  To save the
image size, lower priority pr_*() are compiled out.  I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.

I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-04 10:31:17 -04:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Masahiro Yamada
b5bf5cb3b3 treewide: use #include <...> to include public headers
We are supposed to use #include <...> to include headers in the
public include paths.  We should use #include "..." only for headers
in local directories.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-23 17:53:56 -04:00
Steve Rae
59441ac3c1 mtd: fix compiler warnings
- add missing declaration
- update debug output format specifiers

Signed-off-by: Steve Rae <steve.rae@raedomain.com>
2016-07-24 20:36:29 -05:00
Boris Brezillon
c1fe6b5b5e mtd: nand: Increase the max OOB size
Some NANDs are now exposing 1664 OOB bytes per page. Adjust the
NAND_MAX_OOBSIZE value accordingly.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-07-24 20:36:28 -05:00
Brian Norris
42bd19ce6c mtd: nand: add common DT init code
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.

If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().

The original commit has been slightly reworked to use the fdtdec_xxx()
helpers (instead of the of_xxxx() ones).

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-07-24 20:36:28 -05:00