Reserved bit was changed according to the processors manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Introduce a struct for the BFTICU FPGA to increase the readability of
the code. And the define CONFIG_SYS_BFTICU_BASE was removed because
the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The directory and file mgcoge was renamed to km82xx.
Because other keymile 82xx will follow and will use the
same platform code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The hdlc implementation for mgcoge was initially developed,
but later on not used. Remove the C files, the references
in mgcoge.c and the Makefile to decrease maintenance effort.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
do not define own flash_info variable, instead use
the flash_info variable defined in your flash driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Current timer routines (arch/mips/lib/timer.c) are implemented assuming
that MIPS32 coprocessor (CP0) resources, Counter and Compare registers
in this case, are available. But this doesn't always work.
We need to make sure that all MIPS-based systems don't necessarily use
CP0 counter/compare registers as time keeping resources. And some MIPS
variant processors might come with different hardware specs with genuine
MIPS32 CP0 registers.
With this change, each $(CPU)/ directory can have its own timer code.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
All architectures but MIPS are using --gc-sections on final linking.
This patch introduces that feature for MIPS to reduce the memory and
flash footprint.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Cc: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
Fix style issues and alignments globally. No logical changes.
- Replace C comments with AS line comments where possible
- Use ifndef where possible, rather than if !defined for simplicity
- An instruction executed in a delay slot is now indicated by a leading
space, not by C comment
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
As requested in commit e1390801a3 ([MIPS]
Request for the 'mips_cache_lock()' removal), such feature is no longer
needed for current MIPS implementation of U-Boot, and no one in the tree
uses it for years.
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
The changes introduced by commit 0abddf8 ``cmd_ide: enhance new
feature "CONFIG_IDE_AHB"'' caused compiler warnings like
cmd_ide.c: In function 'ide_init':
cmd_ide.c:716: warning: assignment from incompatible pointer type
Constify the respective function arguments to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
cmd_mdio.c: In function 'mdio_read_ranges':
cmd_mdio.c:97: warning: comparison is always false due to limited range of data type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Fix warning introduced while recent PHY Lib changes:
miiphyutil.c: In function 'miiphy_read':
miiphyutil.c:304: warning: comparison is always false due to limited range of data type
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.
The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
While looking to upgrade to zlib-1.2.5, the current mondo merge of
multiple files into a single was making things way more difficult
than it should have been. Hard to pick out what has been changed
to port it to U-Boot, been removed as useless, and bug fixes added
after the fact.
So split the single file up into the original file names, and merge
non-essential changes back from the original tree (for some reason,
style in code in a bunch of places was changed to U-Boot style even
though this isn't "U-Boot" code).
The original build style is retained -- we have a single zlib.c that
includes all the other files, and that is the only file we compile.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk. Some
are found using an arch-specific rule for looking in CPUDIR, etc.
Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.
Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.
If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.
If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:
$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds
Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules. These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
In order to support boardId / hwkey lists, the u-boot default
environment has been updated: Added a script checkboardidlist
which checks the list of boardId / hwkey if the boadrId / hwkey
of the IVM is included in that list. This feature is used if you
got different HW variants but you only want to create one boot
package. E.g. supx5 board series.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Add:
- introduce "bootrunner" environment variable
This allows to execute consecutive different commands
specified in the list "subbootcmd". If one command fails
the command serie will stop.
- introduce environment variable "develop", "ramfs" and "release"
Each variable is one way to boot our linux. "develop" is for
development purpose and boots the SW via NFS. "release" is for
booting the linux image from flash, "ramfs" allows to load an SW
image via tftp into ram and executes from there
- introduce "addmem" variable, this command adds the used memory
for linux to the bootargs
- introduce "addvar" variable, this command adress for the /var
directory to the kernel command line
- introduce "setramfspram" and "setrootfsaddr" these calculation
were done if "ramfs" was used (only for debugging)
- introduce "tftpramfs" used for "ramfs" to load the image into
RAM (only for debugging)
Remove unneeded stuff:
- CONFIG_IO_MUXING is obsolete for keymile boards
- CONFIG_KM_DEF_ENV_PRIVATE is also obsolete
- define CONFIG_SYS_TEXT_BASE in board configs only
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
This patch adds last_stage_init to all keymile boards. And
in the last stage init some environment variables for u-boot
were set. Currently these are pnvramaddr, pram and var address.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Normaly the PIGGY_MAC_ADRESS can be read directly from the
IVM on keymile boards. On mgcoge3 it differs. Because there
are two piggy boards deployed the second MAC adress must be
calculated with the IVM mac adress and an offset. This patch
allows to set such a offset in the board config.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
define KM_IVM_BUS and KM_ENV_BUS macros
KM_IVM_BUS is used to define the EEprom_ivm environment variable.
These macros allow the reuse of these I2C addresses in other code
locations.
remove unneeded code
On first HW versions the BOCO FPGA was behind a MUX device. These
HW versions are not supported anymore. And therefore this code can
be removed.
added LED initialization for SUEN3
The bootstat LED required to be initialized so to have a green
colour after start-up.
define CONFIG_SYS_TEXT_BASE
This is needed by the relocation code and is not the same for
our ARM BEC and thus needs to be defined.
remove memsize variable
An environment variable for memsize is not needed.
this can be get via the board info struct.
remove unneeded double access to bi_dram[i].size field
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Luca Haab <luca.haab@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This patch fix the i2c deblocking facility with the i2c HW-Controller.
The required delays for byte reading, the enhanced criteria for stop
the dummy read and required 5 start/stop sequences are added.
Add i2c deblocking before ivm eeprom read.
Improve i2c deblocking sequence by respecting stop hold time.
Cleaned function for deblocking. Have now one function i2c_make_abort()
available for bitbang, mpc82xx and mpc83xx harware controller.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
For the kmsupx5 a new header file was introduced km8321-common.h.
Now the common stuff from tuxa1, tuda1 and suvd3 was removed and
the new header file included.
The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are
confusing. Because they actually describe the KMBEC FPGA values.
The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore
all the defines were renamed.
remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is
already declared in keymile-common.h
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
These new values are:
- enables UART0 and UART1 pins in MPP
- define some L2 cache settings
- changes a SDRAM timing to better fit the hardware
- removed three writes that were the same as the reset values
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This patch renames the suen3 defines and functions to KM_KIRKWOOD
which is more generic and more precise, because these values
and functions where used by all suenX boards and not only suen3.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
First step for a cleanup of all header files for km8321 boards.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch reworks all headerfiles for keymile boards. Furthermore
the environment variables are refactored.
Changes:
- introduce km-powerpc.h file and extract ppc specific parts to it
- move ARM specific options and vaiables to km_arm.h
- sort the environment variables to logical groups
- enhance the description of the environment variables
- remove KM specific HW key and board id from kernel command line
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- adapt copyright string
- change bootdelay to 2 seconds
- set max number of command args to 32
- set I/O buffer size to 512
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- use I/O accessors
-> For accessing the FPGA therefore a struct km_bec_fpga
is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
CONFIG_SYS_BOOTMAPSZ has been 64M on these boards for some time so we
should also allow the kernel image to be up to 64M decompressed. This
also matches what we pass to the OS based on the ePAPR specification.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
