In order to support the coming MX6 platform and to reducde
the duplicated code, we had better move some common files
or functions to the imx-common folder for sharing.
This patch does the following:
- move speed.c file from armv7/mx5/speed.c to armv7/imx-common/speed.c
- move armv7/mx5/timer.c to armv7/imx-common/timer.c, no any new feature
added but just fix the checkpatch errors in the old file and remove
the CONFIG_SYS_MX5_CLK32 reference in the file
- create one new file cpu.c file to store the common function with i.mx5/6
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc:Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This corects the warning below, obtained with my gcc 4.6 compiler.
arch/arm/cpu/armv7/mx5/libmx5.o: In function `decode_pll':
arch/arm/cpu/armv7/mx5/clock.c:94: undefined reference to `__aeabi_uldivmod'
I am not able to test this on MX5x hardware, but it does improve the
MAKEALL output for me. You may already have a similar patch, but I cannot
see it on the list.
Signed-off-by: Simon Glass <sjg@chromium.org>
In addition to ensuring that PERCLK remains at least 2.5 times slower
than the AHB clock, certain steps need to be followed to ensure robust
operation of PERCLK when reconfiguring the PERCLK clock source.
To properly configure the PERCLK clock source, the following steps are
required:
1.In the CCGR registers, gate the clocks to all PERCLK-dependent
modules.
2.Select the desired input clock for the PERCLK root clock (to be either
source from the peripherals main source clock or the
lp_apm clock source). Refer to the CMCBR register, perclk_lp_apm_sel bit.
3.Configure the perclk_pred1, perclk_pred2, and perclk_podf dividers
to the desired setting. Refer to the CBCDR register for details.
4.In the CCGR registers, enable the desired clocks for the
PERCLK-dependent module clocks.
If these steps aren't followed, GPT timer may stop and the kernel stops
at "Calibrating delay loop".
Signed-off-by: Terry Lv <r65388@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
The PLL decoding algorithm didn't take into account many configuration bits.
Adjust it according to Linux kernel. Also, add PLL4 for MX53.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Tested-by: Jason Liu <Jason.hui@linaro.org>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
There was already a command to show the processor clocks
for PowerPC (clocks). For i.MX, the "clockinfo" command
was introduce. The patch sets the same command name used on
PowerPC.
A nasty and not needed newline is also dropped in the help for
the command.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This is a port of the official PLL errata workaround from Freescale to
mainline u-boot.
The PLL's in the i.MX51 processor can go out of lock due to a metastable
condition in an analog flip-flop when used at high frequencies.
This workaround implements an undocumented feature in the PLL (dither
mode), which causes the effect of this failure to be much lower (in terms
of frequency deviation), avoiding system failure, or at least decreasing
the likelihood of system failure.
Signed-off-by: David Jander <david@protonic.nl>
In some circumstances, reset_timer_masked() was called be timer_init() in
order to perform architecture specific timer initialisation. In such
cases, the required code in reset_timer_masked() has been moved into
timer_init()
This check was broken. r3 does not contain the silicon revision anymore, so
we need to reload it. Also, this errata only applies to i.MX51.
Signed-off-by: David Jander <david@protonic.nl>
Acked-by: Stefano Babic <sbabic@denx.de>
On i.MX5, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
factor out boot cause function to common code to avoid
the duplicate code in each board support package
Signed-off-by: Jason Liu <jason.hui@linaro.org>
The usage of bss values in drivers before initialisation of bss is forbidden.
In that special case some data in .rel.dyn gets corrupted.
This patch is the same as recently applied for arm926js architecture.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition,
- Add the regs definition, clean up some unused def from mx51,
- Add the low level init support, make use the freq input of setup_pll macro
Signed-off-by: Jason Liu <r64343@freescale.com>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
The patch is to support getting FEC MAC address from fuse bank.
Signed-off-by: Jason Liu <r64343@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
The patch removes the warning:
clock.c:291: warning: initialization from incompatible pointer type
after constification of args[]
Signed-off-by: Stefano Babic <sbabic@denx.de>
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'
Signed-off-by: Jason Liu <r64343@freescale.com>
