This is easier to read than the #ifdef staircase, provides better
visibility into the memory map (alongside the other Kconfig
definitions), and allows these addresses to be reused from code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Starting with H6, Allwinner removed the artificial 32 KiB SPL size limit
from the boot ROM. Now SPL size is only limited by the available SRAM.
This limit ranges from 152 KiB on H6 to a whopping 2052 KiB on R329. To
take advantage of this additional space, we must increase SPL_MAX_SIZE.
Since we do not want to unnecessarily pad SPL out to these giant sizes,
we must set SPL_PAD_TO to zero. This causes no problems because binman
already takes care of appending the SPL payload at the right offset.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
FriendlyElec NanoPi Duo2 is a tiny SBC with Allwinner H3 and
Ampak AP6212 WiFi module. The device-tree for it is already
available in u-boot source tree. Add a default config for it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
[Andre: enable USB gadgets]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Make the "phy-handle" property optional, which allows support
for a fixed-link phy configuration.
Thus if the "phy-handle" is present in a DT, then driver will work as
before. Otherwise, phyaddr initialization will not be necessary,
as it is not needed in case of a fixed-link config.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
This is a Chinese TV box based on Allwinner H618 SoC.
The DRAM parameters were derived from the values found in a firmware update.
Signed-off-by: Nick Alilovic <nickalilovic@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the official Linux kernel tree, v6.8-rc1.
This time only small changes in the existing files, but five new boards
got added, which opens the door for their respective defconfig files.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Infineon(Cypress) S28HS02GT is 1.8V, 2Gb (256MB) NOR Flash memory with
Octal interface. It is a dual-die package parts and has same features
with existing S28 series.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enabling Octal DTR mode in multi-die package parts requires reister setup
for each die. That can be done by simple for-loop. write_enable() takes
effect to all die at once so we can call it before the loop. Besides we
can replace spi_mem_exec_op() calls with spansion_read/write_any_reg().
And finally, we must mask CFR2V[7:4] when changing dummy cycles, as
CFR2V[7] indicates current addressing mode and that should be 1 (4-byte
address mode) for multi-die package parts.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_post_bfpt_fixup() fixes erase opcode, erase size, and page size.
s25_post_bfpt_fixup() is doing same thing including multi-die support.
We can consolidate s28hx_t_post_bfpt_fixup() and s25_post_bfpt_fixup()
into one named s25_s28_post_bfpt_fixup().
In s25_s28_post_bfpt_fixup(), set_4byte() is called to force the device to
be 4-byte addressing mode. In S28HS02GT datasheet, the B7 opcode is missing
but it works actually (confirmed).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s28hx_t_setup() only checks sector layout setting. To support multi-die
package parts like S28HS02GT, it needs to check device size and assign
ready() hook for multi-die package parts. These are covered in s25_setup()
so we can consolidate s28hx_t_setup() and s25_setup() into one named
s25_s28_setup().
spi_nor_wait_till_ready() at the beginning of s28hx_t_setup() can be
removed since there is no op that makes device busy state before setup.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_mdp_ready() handles status polling for multi-die package parts that
requires to read and check status register for each die. To support
S28HS02GT(dual-die package with Octal DTR support), rename function and
use nor->rdsr_dummy in octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Infineon(Cypress) S28Hx-T family does not support legacy CLSR(0x30) opcode.
Instead, it supports CLPEF(0x82) which has the same functionality as CLSR.
spansion_sr_ready() is for multi-die package parts including S28HS02GT, so
we need to use CLPEF instead of CLSR.
This change does not affect to S25x02GT which uses spansion_sr_ready() as
S25Hx-T family also supports CLPEF(0x82) as well as CLSR(0x30).
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
In Infineon multi-die package parts, we need to use Read Any Register op
to read status register in 2nd or further die. Infineon S28HS02GT is
dual-die package and supports Octal DTR interface. To support this,
spansion_read_any_reg() needs to be reworked. Implementation is similar
to existing read_sr() that already supports Octal DTR mode.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
s25_erase_non_uniform() and s28hx_t_erase_uniform() support hybrid sector
layout (32 x 4KB sectors overlaid at bottom address) and doing same thing.
Consolidate them into single helper named s25_s28_erase_non_uniform().
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some macro definitions used in Infineon(Cypress) S25 and S28 series are
redundant and some have inconsistent prefix. This patch removes
redundant ones and renames some to have same prefix as others.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The current implementation encounters issues when testing data ranging
from 0 to 8 bytes. This was confirmed through testing with both ISSI
(IS25WX256) and Micron (MT35XU02G) Flash exclusively in SDR mode.
Upon investigation, it was observed that utilizing the
"SPI_NOR_OCTAL_READ" flag and attempting to read less than 8 bytes in
STIG mode results in a read failure, leading to a compare test failure.
To resolve this issue, the CMD_4BYTE_FAST_READ opcode is now utilized
instead of CMD_4BYTE_OCTAL_READ, specifically in SDR mode.
This is based on patch series:
https://lore.kernel.org/all/cover.1701853668.git.tejas.arvind.bhumkar@amd.com/
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Added support for the ISSI OSPI flash part IS25LX512M.
Initial testing was performed on the Tenzing-se1 board using
SDR mode, covering basic erase, write, and readback operations.
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If even one byte is lost due to Rx FIFO overflow then we will never
exit the read loop. Because the (priv->rx != priv->rx_end) condition will
be always true.
Let's check if Rx FIFO overflow occurred and exit the read loop
in this case.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
efi_get_variable_int() may fail, the buffer should be
cleared before using it.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Addresses-Coverity-ID: 478333 ("Error handling issues")
The code in find_smbios_table() is redundant to
efi_get_configuration_table(). Replace it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use library function efi_get_configuration_table() to find the ESRT.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In multiple places we need a function to find an EFI configuration table.
Rename get_config_table() to efi_get_configuration_table() and export it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
the file pytest.py does not exist
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
EFI binaries should not contain sections that are both writable and
executable. Separate the RX .text section from the RW .data section
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Change the alignment of the relocation code in EFI binaries to match page
boundaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fix conflicting SPDX license information in linker scripts introduced by
commit 7215787c4e ("SPDX: Convert single license tags to Linux Kernel
style").
Fixes: 7215787c4e ("SPDX: Convert single license tags to Linux Kernel style")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If an error occurs we may see an output like:
EFI application calling Exit
Could not open loaded image protocolLoaded image protocol missing
Add the missing line feed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
That's most probably a typo, because driver model design documents seem
to be from 2012 and there is no 2010.01 release.
Fixes: 282ed24fb3 ("dm: MIGRATION: Add migration plan for CONFIG_DM")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At the moment every Allwinner board builds and requires an SPL, even
though we select this individually in each _defconfig file.
For experiments and for early bringup of new SoCs it would be beneficial
to only build U-Boot proper, for instance to postpone a tedious SPL port
(including DRAM support) in the initial phase.
Protect some SPL related symbols that we unconditionally select at the
moment with "if SPL", to avoid Kconfig conflicts when CONFIG_SPL is
disabled.
This alone does not cleanly build U-Boot proper only yet, but gets it
far enough so that the binary can be harvested.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The usage of the common.h include file is deprecated, and has already
been removed from several files.
Get rid of all inclusions in the arch/arm/mach-sunxi directory. Most
files actually don't need the header at all, for the few others just
include the headers that we actually require.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun9i.h header file defined the base addresses for quite some
peripherals of the Allwinner A80 CPU, even though we now only use a
fraction of that.
Most of the addresses are now either read from the DT, or were never
used in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun4i.h header file defined the base addresses for quite some
peripherals of earlier Allwinner CPUs, even though we now only use a
fraction of that.
Most of the addresses are now either read from the DT, or were never
used in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The cpu_sun50i_h6.h header file defined the base addresses for quite some
peripherals of the Allwinner H6 and related CPUs, even though we now only
use a fraction of that.
Most of the addresses are now either read from the DT, or were never used
in U-Boot in the first place.
Removed the ones that are not used in the whole of the U-Boot source.
to make it clear that this file only contains addresses that are needed
for the SPL operation.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sunxi-common.h configs header used to contain a lot of random
Allwinner platform related constants, but over the years we moved a lot
of those definitions out there.
Clean up the file to remove outdated comments which are leftovers from
the olden days. Also remove the definition of LOW_LEVEL_SRAM_STACK,
which is actually used nowhere in the whole source tree.
This also uses the opportunity to add some section comments that helps
structuring the header file and improving readability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Drop leading space in front of a comment. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Include missing asm/arch/rmobile.h in board/renesas/rcar-common/v3-common.c
to prevent build failure of r8a77970_eagle r8a779a0_falcon r8a77980_v3hsk
and r8a77970_v3msk .
Include missing asm/u-boot.h in falcon.c and grpeach.c to fix build failure
due to missing definition of struct bd_info . Include errno.h in grpeach.c
to fix build error due to missing definition of EINVAL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
The header file is not necessary in either of those files,
remove it as common.h is going away.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Paul Barker <paul.barker.ct@bp.renesas.com>
* Add missing field to SMBIOS type 2 structure definition
* Provide smbios command to display smbios table
* Enable the command on sandbox and qemu_arm64_defconfig
* Provide a python test for the smbios command
* Fix copying SMBIOS 2.1 table from QEMU
* Correct EFI TCG measurement to assume SMBIOS 3 table
-----BEGIN PGP SIGNATURE-----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=jv3i
-----END PGP SIGNATURE-----
Merge tag 'smbios-2024-04-rc1-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request smbios-2024-04-rc1-2
* Add missing field to SMBIOS type 2 structure definition
* Provide smbios command to display smbios table
* Enable the command on sandbox and qemu_arm64_defconfig
* Provide a python test for the smbios command
* Fix copying SMBIOS 2.1 table from QEMU
* Correct EFI TCG measurement to assume SMBIOS 3 table
As we support installing SMBIOS3 tables in U-Boot we need to add this GUID
to the translation table used buy uuid_guid_get_str().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The current code convert the SMBIOS 2.1 entry point structure to
SMBIOS 3.0 entry point structure. The max_struct_size member in
SMBIOS 2.1 entry point structure indicates
"Size of the largest SMBIOS structure, in bytes".
We need to use struct_table_length instead.
Fixes: 1c5aab803c ("smbios: copy QEMU tables")
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Current U-Boot only supports the SMBIOS 3.0 entry point structure.
TCG2 measurement code should migrate to SMBIOS 3.0 entry
point structure.
efi_selftest tcg2 test also needs to be updated, and expected
PCR[1] result is changed since guid for SMBIOS EFI system table
uses different guid SMBIOS3_TABLE_GUID instead of SMBIOS_TABLE_GUID.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We have a Python test the copying of SMBIOS tables from QEMU.
To make use of the test we need the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
To make use of the Python smbios test we need the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a unit test for the smbios command.
Provide different test functions for QEMU, sandbox, and other systems.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide a man-page for the smbios command.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
U-Boot can either generated an SMBIOS table or copy it from a prior boot
stage, e.g. QEMU.
Provide a command to display the SMBIOS information.
Currently only type 1 and 2 are translated to human readable text.
Other types may be added later. Currently only a hexdump and the list of
strings is provided for these.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The type 2 structure must include information about the contained objects.
It is fine to set the number of contained object handles to 0.
Add the missing field.
Fixes: 721e992a8a ("x86: Add SMBIOS table support")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
