Commit graph

8867 commits

Author SHA1 Message Date
Siva Durga Prasad Paladugu
8964f24179 net: xilinx_axi: Clear Isolate bit if found during phy setup
In SGMII cases the isolate bit might set after DMA and
ethernet resets and hence check and clear during
setup_phy if it was set.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Siva Durga Prasad Paladugu
9c0da76220 net: xilinx_axi: Use interface type instead of zero
Pass appropriate interface type to phy_connect
instead of zero.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Siva Durga Prasad Paladugu
a06c341faa net: zynq_gem: Add support for SGMII interface
Add support of SGMII interface for zynq GEM.
Read xlnx,emio property from DT.

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Siva Durga Prasad Paladugu
ed6fad3e25 phy: Add phy driver support for xilinx PCS/PMA core
Add phy driver support for xilinx PCS/PMA core

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-04-04 20:10:44 +02:00
Karsten Merker
563d8d9358 net: phy: Realtek RTL8211B/C PHY ID fix
The RTL8211B_driver structure in drivers/net/phy/realtek.c contains a
wrong PHY ID (0x1cc910 instead of 0x1cc912) in the uid field.

The lowest four bits of the PHY ID encode the chip revision (B+C/D/E/F)
of the RTL8211 and the code originally applied a mask of 0xfffff0 to
the PHY ID, so that matching the PHY ID to the appropriate driver code
was only done on the chip type (RTL8211), but not on a specific
revision.

After introduction of support for the RTL8211E, which needed another
startup function than the older chip revisions, commit
4220504767 changed the mask to 0xffffff
to make the chip revision relevant for the match, but didn't provide
the now-relevant lower bits of the uid field for the RTL8211B/C.

Fix this by setting the full PHY ID in the RTL8211B_driver uid field.

Fixes: 4220504767 ("net/phy: realtek: Fix the PHY ID mask to ensure the correct Realtek PHY is detected")
Signed-off-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-04-02 19:26:08 -04:00
Eric Nelson
e40cf34a29 drivers: block: add block device cache
Add a block device cache to speed up repeated reads of block devices by
various filesystems.

This small amount of cache can dramatically speed up filesystem
operations by skipping repeated reads of common areas of a block
device (typically directory structures).

This has shown to have some benefit on FAT filesystem operations of
loading a kernel and RAM disk, but more dramatic benefits on ext4
filesystems when the kernel and/or RAM disk are spread across
multiple extent header structures as described in commit fc0fc50.

The cache is implemented through a minimal list (block_cache) maintained
in most-recently-used order and count of the current number of entries
(cache_count). It uses a maximum block count setting to prevent copies
of large block reads and an upper bound on the number of cached areas.

The maximum number of entries in the cache defaults to 32 and the maximum
number of blocks per cache entry has a default of 2, which has shown to
produce the best results on testing of ext4 and FAT filesystems.

The 'blkcache' command (enabled through CONFIG_CMD_BLOCK_CACHE) allows
changing these values and can be used to tune for a particular filesystem
layout.

Signed-off-by: Eric Nelson <eric@nelint.com>
2016-04-01 17:18:27 -04:00
Mateusz Kulikowski
120800df72 gpio: Add support for Qualcomm PM8916 gpios
This driver supports GPIOs present on PM8916 PMIC.
There are 2 device drivers inside:
- GPIO driver (4 "generic" GPIOs)
- Keypad driver that presents itself as GPIO with 2 inputs (power and reset)

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:13 -04:00
Mateusz Kulikowski
c2f74c8f53 pmic: Add support for Qualcomm PM8916 PMIC
This PMIC is connected on SPMI bus so needs SPMI support enabled.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:13 -04:00
Mateusz Kulikowski
5b47271c18 drivers: spmi: Add support for Qualcomm SPMI bus driver
Support SPMI arbiter on Qualcomm Snapdragon devices.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:12 -04:00
Mateusz Kulikowski
d33776e43d spmi: Add sandbox test driver
This patch adds emulated spmi bus controller with part of
pm8916 pmic on it to sandbox and tests validating SPMI uclass.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:12 -04:00
Mateusz Kulikowski
04868b407b drivers: Add SPMI bus uclass
Qualcom processors use proprietary bus to talk with PMIC devices -
SPMI (System Power Management Interface).
On wiring level it is similar to I2C, but on protocol level, it's
multi-master and has simple autodetection capabilities.
This commit adds simple uclass that provides bus read/write interface.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:12 -04:00
Mateusz Kulikowski
5a8221181e ehci: Add support for Qualcomm EHCI
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:11 -04:00
Mateusz Kulikowski
d144f96a48 ehci-ci.h: drop generic USBCMD fields
Use definitions from ehci.h instead.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:11 -04:00
Mateusz Kulikowski
e162c6b1a7 usb: Rename ehci-fsl.h to ehci-ci.h
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.

This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:10 -04:00
Mateusz Kulikowski
64160a545d eth: asix88179: Print packet length properly
Debug printf used '%u' to print size_t variable.
This caused warnings on 64-bit machines.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-04-01 17:18:10 -04:00
Mateusz Kulikowski
d3d844f84a usb: ulpi: Fix compile warning in read/write on 64-bit machines.
ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
Code generates compilation warnings on 64-bit machines where pointer
is cast to u32.

This patch drops all but last 8 bits of register address.
It is possible, because addresses on ULPI bus are 6- or 8-bit.

It is not possible (according to ULPI 1.1 spec) to have more
than 8-bit addressing.

This patch should not cause regressions as all calls to
ulpi_read/write use either structure pointer (@ address 0) or integer
offsets cast to pointer - addresses requested are way below 8-bit range.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
2016-04-01 17:18:09 -04:00
Mateusz Kulikowski
6b14fbbdc6 usb: ulpi: Add Kconfig options for ULPI
The following options can be now enabled via defconfig:
- CONFIG_USB_ULPI
- CONFIG_USB_ULPI_VIEWPORT
- CONFIG_USB_ULPI_VIEWPORT_OMAP

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
2016-04-01 17:18:08 -04:00
Mateusz Kulikowski
3f9f8a5b83 ehci-hcd: Add init_after_reset
Some host controllers need addidional initialization after ehci_reset()
In non-dm implementation it is possible to use CONFIG_EHCI_HCD_INIT_AFTER_RESET.
This patch adds similar option to ehci drivers using dm.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:08 -04:00
Mateusz Kulikowski
9d11d12a16 mmc: Add support for Qualcomm SDHCI controller
Add support for SD/eMMC controller present on some Qualcomm Snapdragon
devices. This controller implements SDHCI 2.0 interface but requires
vendor-specific initialization.
Driver works in PIO mode as ADMA is not supported by U-Boot (yet).

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:08 -04:00
Mateusz Kulikowski
81a87e1894 gpio: Add support for Qualcomm gpio controller
Add support for gpio controllers on Qualcomm Snapdragon devices.
This devices are usually called Top Level Mode Multiplexing in
Qualcomm documentation.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:07 -04:00
Mateusz Kulikowski
142a20c367 serial: Add support for Qualcomm serial port
This driver works in "new" Data Mover UART mode, so
will be compatible with modern Qualcomm chips only.

Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2016-04-01 17:18:07 -04:00
Stephen Warren
e320f0bc9b smsc95xx: fix operation on 64-bit systems
smsc95xx_read_reg() should calculate sizeof(*data) not sizeof(data) since
data is a pointer, and the value pointed at is being transferred over USB,
not the value of the pointer. This fixes operation of the driver in 64-bit
builds, such as the Raspberry Pi 3.

Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-04-01 17:17:40 -04:00
Rob Herring
74322201dd fastboot: allow retrieving fastboot variables from env
Some boards need to expose device specific variable through fastboot
(to adpat the flashing script depending on hardware revision for
example).

Provide a way to expose custom fastboot variables. Note that all
variables meant to be exposed through fastboot should be be prefixed
with 'fastboot.', the variable should not exceed 32 bytes (including
the prefix and the trailing '\0') and the variable content should
fit in the response buffer (60 bytes excluding the 'OKAY' prefix and
the trailing '\0').

Signed-off-by: Rob Herring <rob.herring@linaro.org>
[Boris Brezillon: add a commit message]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Steve Rae <srae@broadcom.com>
2016-04-01 17:17:40 -04:00
Tom Rini
40345e9ea7 Merge branch 'master' of http://git.denx.de/u-boot-sunxi 2016-04-01 08:17:55 -04:00
Siarhei Siamashka
d96ebc468d sunxi: Add support for Allwinner A64 SoCs
The Allwinner A64 SoC is used in the Pine64. This patch adds
all bits necessary to compile U-Boot for it running in AArch64
mode.

Unfortunately SPL is not ready yet due to legal problems, so
we need to boot using the binary boot0 for now.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[agraf: remove SPL code, move to AArch64]
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Alexander Graf
0ea5a04fbc sunxi: Explicitly cast u32 pointer conversions
Some parts of the sunxi code cast explicitly between u32 values and pointers.
This is not a problem in practice, because all 64bit SoCs today only use the
lower 32 bits for their phyical address space. But we need to make sure that
the compiler is sure this is not an accident as well.

Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-04-01 09:52:28 +02:00
Masahiro Yamada
6105aa2f2a pinctrl: uniphier: support UniPhier PH1-LD11 pinctrl driver
The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:57:19 +09:00
Masahiro Yamada
8a3328c209 pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver
Add pin configuration and pinmux support for UniPhier PH1-LD20 SoC.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:57:15 +09:00
Masahiro Yamada
3b05b5f0e4 pinctrl: uniphier: support per-pin input enable for new SoCs
Upcoming new pinctrl drivers for PH1-LD11 and PH-LD20 support input
signal gating for each pin.  (While, existing ones only support it
per pin-group.)  This commit prepares the core part for that.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:56:07 +09:00
Masahiro Yamada
8cc92b996d pinctrl: uniphier: introduce capability flag
The core part of the UniPhier pinctrl driver needs to support a new
capability for upcoming UniPhier ARMv8 SoCs.  This sometimes happens
because pinctrl drivers include really SoC-specific stuff.

This commit intends to tidy up SoC-specific parameters of the existing
drivers before adding new ones.  Having flags would be better than
adding new members every time a new SoC-specific capability comes up.

At this time, there is one flag, UNIPHIER_PINCTRL_CAPS_DBGMUX_SEPARATE.
This capability (I'd say rather quirk) was added for PH1-Pro4 and
PH1-Pro5 as requirement from our customer.  For those SoCs, one pin-mux
setting is controlled by the combination of two separate registers; the
LSB bits at register offset (8 * N) and the MSB bits at (8 * N + 4).
Because it is impossible to update two separate registers atomically,
the LOAD_PINCTRL register should be set in order to make the pin-mux
settings really effective.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:54:00 +09:00
Masahiro Yamada
510454db04 pinctrl: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:25 +09:00
Masahiro Yamada
4f80501b91 mmc: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:19 +09:00
Masahiro Yamada
bc82a1310f gpio: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:19 +09:00
Masahiro Yamada
336399fb63 i2c: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:13 +09:00
Masahiro Yamada
45a3b1fd6c clk: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:08 +09:00
Masahiro Yamada
b37a1ccea2 serial: uniphier: use devm_get_addr() to get base address
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties.  (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:17:07 +09:00
Graham Moore
15305c2f03 mtd: nand: denali: max_banks calculation changed in revision 5.1
Read Denali hardware revision number and use it to
calculate max_banks,  The encoding of max_banks changed
in Denali revision 5.1.

[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]

Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-04-01 00:16:55 +09:00
Chen-Yu Tsai
045ae7e339 sunxi: ohci: Add A83T compatible
We have a separate compatible for almost each SoC. Add one for the A83T.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:04:13 +02:00
Chen-Yu Tsai
3655f287b6 sunxi: ehci: Add A83T compatible
We have a separate compatible for almost each SoC. Add one for the A83T.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:04:11 +02:00
Chen-Yu Tsai
38491d9c65 power: axp818: Add support for FLDOs
The FLDOs on AXP818 PMIC normally provide power to CPUS and USB HSIC PHY
on the A83T/H8.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:03:58 +02:00
Chen-Yu Tsai
4c6a9ca103 power: axp818: Fix DCDC5 default voltage
DCDC5 is designed to supply VCC-DRAM, which is normally 1.5V for DDR3,
1.35V for DDR3L, and 1.2V for LPDDR3.

Also remove CONFIG_AXP_DCDC5_VOLT from h8_homlet_v2_defconfig.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:03:56 +02:00
Chen-Yu Tsai
81a8aa3a39 sunxi: axp: Generalize register macros for VBUS drive GPIO
VBUS drive is supported on AXP221 and later PMICs. Rework the macros
so we can support this on later PMICs without too much work.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:03:52 +02:00
Chen-Yu Tsai
96fccb175f musb: sunxi: Add support for A83T
Like the Allwinner A33 SoC, the A83T is missing the config register
from the musb USB DRD hardware block. Use a known working value for
it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 17:03:49 +02:00
Michael Haas
525d187afb net: phy: Optionally force master mode for RTL PHY
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this
define is set, RTL8211x PHYs (except for the RTL8211F) will have their
1000BASE-T master/slave autonegotiation disabled and forced to master
mode.

This is helpful for PHYs like the RTL8211C which produce unstable links
in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB
and A20-OLinuXino-Lime2.

There is no proper way to identify affected PHYs in software as the
RTL8211C shares its UID with the RTL8211B. Thus, this fix requires
the introduction of an #ifdef.

CC: fradav@gmail.com
CC: merker@debian.org
CC: hdegoede@redhat.com
CC: ijc@hellion.org.uk
CC: joe.hershberger@ni.com

Signed-off-by: Michael Haas <haas@computerlinguist.org>
Tested-by: Karsten Merker <merker@debian.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-31 14:29:11 +02:00
Tom Rini
0badc648dc Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-03-29 12:58:45 -04:00
Saksham Jain
8a6f83dcb8 crypto/fsl: Make CAAM transactions cacheable
This commit solves CAAM coherency issue on ls2080. When caches are
enabled and CAAM's DMA's AXI transcations are not made cacheable,
Core reads/writes data from/to caches and CAAM does from main memory.
This forces data flushes to synchronize various data structures. But
even if any data in proximity of these structures is read by core,
these structures again are fetched in caches.

To avoid this problem, either all the data that CAAM accesses can be
made cache line aligned or CAAM transcations can be made cacheable.

So, this commit makes CAAM transcations as write back with write and
read allocate.

Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:22 -07:00
Saksham Jain
69b6a796f7 crypto/fsl: Correct 64-bit write when MMU disabled
When MMU is disabled, 64-bit write must be aligned at 64-bit
boundary. Becaue the memory location is not guaranteed to be 64-bit
aligned, the 64-bit write needs to be split into two 32-bit writes
to avoid the alignment exception.

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Saksham Jain <saksham.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:22 -07:00
Prabhakar Kushwaha
b576d325ac driver: net: fsl-mc: Check NULL before pointer dereference
NULL pointer should be checked before any dereference.  This patch
move memest after the NULL pointer check.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-29 08:46:01 -07:00
Prabhakar Kushwaha
cd7b3fbcf4 driver: net: fsl-mc: Free dflt_dpio pointer after its usage
Free dflt_dpio pointer after its usage during error handling

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reported-by: Jose Rivera <german.rivera@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-03-28 17:35:38 -07:00
Guy Thouret
32b9b556f7 omap24xx_i2c: Implement CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
Signed-off-by: Guy Thouret <guy.thouret@wems.co.uk>
Cc: Heiko Schocher <hs@denx.de>
2016-03-28 09:23:28 +02:00