Add U-Boot SPI support for the RK3328
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(fix checkpatch error for code ident)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RK3328 SPI controller
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add SPI support for the RK3328 clock driver
Signed-off-by: Johannes Krottmayer <krjdev@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adjust the ENV offset, size to fit into all images
on 16MB flash.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC3 core, gadget for roc-rk3399-pc board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable config options to get HDMI output on RockPI-4 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB gadget for rock-pi-4 boards.
This would help to use fastboot by default.
Note: Connect the Host USB cable (Port A or C) to rock-pi-4
Upper USB 3.0 port.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable PCI/NVME for M.2 Slot on RockPI-4 boards.
=> nvme info
Device 0: Vendor: 0x144d Rev: 2B2QEXM7 Prod: S4EUNG0MC10012Y
Type: Hard Disk
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPI-4 boards.
Note that the Upper USB3.0 port is marked as otg and
lower USB3.0 port marked as host, so this below log
capture when USB3.0 mass storage plug in at lower
USB 3.0 port.
Log:
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... 1 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (5 Gb/s, 0mA)
U-Boot XHCI Host Controller
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 224mA)
SanDisk Dual Drive 040130e3ee554b7078843f4eb331646
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for RockPro64 boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Also known as Odroid Go Advance but named Go2 internally by the
vendor it seems.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3326 is just a trimmed down px30 from a software perspective,
so the mainline rk3326 dtsi also ist just a tiny addition.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A large number of assorted fixes, including but not limited to:
- Correct fixdep and CONFIG_IS_ENABLED(...)
- lz4 on big endian
- Assorted LMB hardening
- Remove bd_t typedef
Add VendorID and DeviceID for supported devices on OcteonTX/TX2
platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When update_uboot.its is used directly there is syntax error for no reason.
Error report:
mkimage -f update_uboot.its boot
Error: update_uboot.its:18.12-13 syntax error
FATAL ERROR: Unable to parse input tree
mkimage: Can't read boot.tmp: Invalid argument
Fixes: 4bae90904b ("Automatic software update from TFTP server")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The types of "offset" and "size" of "struct mtd_partition" are uint64_t,
while mtd_parse_partitions() uses int to work with these values. When
the offset reaches 2GB, it is interpreted as a negative value, which
leads to error messages like
mtd: partition "<partition name>" is out of reach -- disabled
eg. when using the "ubi part" command.
Fix this by using uint64_t for cur_off and cur_sz.
Signed-off-by: Martin Kaistra <martin.kaistra@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
When fixdep detects CONFIG_IS_ENABLED and other similar macros, it must
parse the macro parameter to determine which actual CONFIG_ option is
being referenced. This involves moving a pointer forward through the
entire CONFIG_ option "word". Currently, the code uses variable q to walk
through the word, but doesn't actually initialize it to point at the
parameter before doing so. Consequently, the walking process immediately
fails since it sees the macro invocatoins's ( rather than the expected
alpha-numeric characters in the macro parameter. Fix this by adding the
missing initialization.
Fixes: 67f2ee86cc ("kbuild: fixdep: Resync this with v4.17")
Fixes: 7012865e96 ("gpio: fix test.py for gpio label lookup")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new error message in case the size of data written
are shorter than the one expected.
Currently, it will lead to the following error message:
"mkimage: Write error on uImage: Success"
This is not explicit when the error is because the device
doesn't have enough space. Let's use a more understandable message:
"mkimage: Write only 4202432/4682240 bytes, probably no space left on the device"
Signed-off-by: Mylène Josserand <mylene.josserand@collabora.com>
Reviewed-by: Walter Lozano <walter.lozano@collabora.com>
Since commit 4b0bcfa7c4 (Kconfig: Migrate CONFIG_BOOTM_* options),
the config_defaults.h file has been void of any actual content - and
these days, "sane defaults for everyone" is achieved by appropriate
default values in Kconfig. Remove it, and thus make every translation
unit process one less header file.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Remove the incorrect usage of double underscores for the
CONFIG_OF_LIST and CONFIG_SPL_OF_LIST symbols.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
If a file cannot be loaded, show an error message.
Set the EFI boot device only after successfully loading a file.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some code was not converted by coccinelle, somehow.
I manually fixed up the remaining, and comments, README docs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[trini: Add arch/arm/mach-davinci/include/mach/sdmmc_defs.h and
include/fdt_support.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
All configurations have been removed in 2016 by commit 7985cdf74b
("arm64: Remove non-full-va map code").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This fixes the CVE-2016-9840. Commit imported from [1].
inftrees.c was subtracting an offset from a pointer to an array,
in order to provide a pointer that allowed indexing starting at
the offset. This is not compliant with the C standard, for which
the behavior of a pointer decremented before its allocated memory
is undefined. Per the recommendation of a security audit of the
zlib code by Trail of Bits and TrustInSoft, in support of the
Mozilla Foundation, this tiny optimization was removed, in order
to avoid the possibility of undefined behavior.
[1]: 6a043145ca
Signed-off-by: Mark Adler <madler@alumni.caltech.edu>
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
- Despite other ext4 filesystem functions, ext4fs_mount returns
0 in case of error.
- This leads to u-boot crash in case that an SD card
with valid partition table but without ext4 filesystem created
in a partition is found on SD card.
- Fix this by returning a proper error code of '-1' from spl_load_image_ext
function in case of ext4fs_mount error.
Signed-off-by: Thomas Schaefer <thomas.schaefer@kontron.com>
[hthiery: slightly reword the commit message]
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Moving of the OS image may have some nasty side effects like corrupting
DTB. Convert the current debug print to printf so that the relocation of
the OS is always obvious to the user.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
These cases are typically fatal and are difficult to debug for random
users. Add checks for detecting overlapping images and abort if overlap
is detected.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Currently the boot continues if the FDT image is clearly corrupted,
which just causes the loaded OS to hang. Abort boot properly if the FDT
is corrupted.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Booting an lz4-compressed kernel image fails on our powerpc board with
-EPROTONOSUPPORT. Adding a bit of debug prints, we get
magic: 0x184d2204
flags: 0x64
reserved0: 1
has_content_checksum: 1
has_content_size: 0
has_block_checksum: 0
independent_blocks: 1
version: 0
block_descriptor: 70
reserved1: 7
max_block_size: 0
reserved2: 0
So the magic is ok, but the version check fails, also some reserved
bits are apparently set. But that's because the code interprets the
"flags" and "block_descriptor" bytes wrongly:
Using bit-fields to access individual bits of an "on the wire" format
is not portable, not even when restricted to the C flavour implemented
by gcc. Quoting the gcc manual:
* 'The order of allocation of bit-fields within a unit (C90 6.5.2.1,
C99 and C11 6.7.2.1).'
Determined by ABI.
and indeed, the PPC Processor ABI supplement says
* Bit-fields are allocated from right to left (least to most
significant) on Little-Endian implementations and from left to
right (most to least significant) on Big-Endian implementations.
The upstream code (github.com/lz4/lz4) uses explicit shifts and masks
for encoding/decoding:
/* FLG Byte */
*dstPtr++ = (BYTE)(((1 & _2BITS) << 6) /* Version('01') */
+ ((cctxPtr->prefs.frameInfo.blockMode & _1BIT ) << 5)
+ ((cctxPtr->prefs.frameInfo.blockChecksumFlag & _1BIT ) << 4)
+ ((unsigned)(cctxPtr->prefs.frameInfo.contentSize > 0) << 3)
+ ((cctxPtr->prefs.frameInfo.contentChecksumFlag & _1BIT ) << 2)
+ (cctxPtr->prefs.frameInfo.dictID > 0) );
/* Flags */
{ U32 const FLG = srcPtr[4];
U32 const version = (FLG>>6) & _2BITS;
blockChecksumFlag = (FLG>>4) & _1BIT;
blockMode = (FLG>>5) & _1BIT;
contentSizeFlag = (FLG>>3) & _1BIT;
contentChecksumFlag = (FLG>>2) & _1BIT;
dictIDFlag = FLG & _1BIT;
/* validate */
if (((FLG>>1)&_1BIT) != 0) return err0r(LZ4F_ERROR_reservedFlag_set); /* Reserved bit */
if (version != 1) return err0r(LZ4F_ERROR_headerVersion_wrong); /* Version Number, only supported value */
}
Do the same here, and while at it, be more careful to use unaligned
accessors to what is most likely unaligned. Also update the comment to
make it clear that it only refers to the lz4.c file, not the following
code of lz4_wrapper.c.
This has been tested partly, of course, by seeing that my
lz4-compressed kernel now boots, partly by running the (de)compression
test-suite in the (x86_64) sandbox - i.e., it should still work just
fine on little-endian hosts.
Reviewed-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Move doc/README.coccinelle to doc/develop/coccinelle.rst using the current
linux-next version of the text.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
This should ideally be used by all x86 boards in U-Boot. Enable it by
default. If some boards don't use it, the cost is small.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function sounds like something that is called when U-Boot is about to
jump to Linux. In fact it is an init function.
Rename it to reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Currently U-Boot implements version 2 but reports version 4. Correct it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
This function does not exist anymore. Drop it from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The comment here applies only to FSP1, so update it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
At present this information is used to locate and parse the tables but is
not stored. Store it so that we can display it to the user, e.g. with the
'bdinfo' command.
Note that now the GD_FLG_SKIP_LL_INIT flag is set in get_coreboot_info(),
so it is always set when booting from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Update this code to calculate the address to use, rather than hard-coding
it. Obtain the requested stack size from the FSP.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If there is MRC information we should run FSP-M with a different
boot_mode flag since it is supposed to do a 'fast path' through the
memory init. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Writing tables is currently pretty opaque. Add a bit of debugging to the
process so we can see what tables are written and where they start/end in
memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
The FSP-S changes the ITSS priorities. The code that tries to save it
before running FSP-S and restore it afterwards does not work as U-Boot
relocates in between the save and restore. This means that the driver
data saved before relocation is lost and the new driver just sees zeroes.
Fix this by allocating space in the relocated memory for the ITSS data.
Save it there and access it from the driver after relocation.
This fixes interrupt handling on coral.
Also drop the log_msg_ret() in irq_first_device_type() since this function
can be called speculatively in places where we are not sure if there is
an interrupt controller of that type. The resulting log errors are
confusing when there is no error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
