Update the memory layout to be aligned with other platform and avoid
overlap with 32MB Linux kernel (multiv7 image).
+ Kernel => 32MiB offset = 0xC2000000
and increase the bootm size to 32MiB
+ FDT => 64MiB offset = 0xc4000000
+ SCRIPT => 65Mib offset = 0xc4100000
+ PXESCRIPT => 66Mib offset = 0xc4200000
+ SPLASHIMAGE => 67Mib offset = 0xc4300000
+ RAMDISK => 68Mib offset = 0xc4400000
(not limited size)
In sources/boot/u-boot/doc/README.distro
+ kernel_addr_r: A size of 16MB for the kernel is likely adequate.
+ pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate.
+ fdt_addr_r: A size of 1MB for the FDT/DTB seems reasonable.
+ ramdisk_addr_r: It is recommended that this location be highest in RAM
out of fdt_addr_, kernel_addr_r, and ramdisk_addr_r,
so that the RAM disk can vary in size and use any
available RAM.
+ pxefile_addr_r: A size of 1MB for extlinux.conf is more than adequate.
+ scriptaddr: A size of 1MB for extlinux.conf is more than adequate.
For suggestions on memory locations for ARM systems, you must follow
the guidelines specified in Documentation/arm/Booting
in the Linux kernel tree.
And in sources/linux-stm32mp/Documentation/arm/Booting
The zImage may also be placed in system RAM and called there. The
kernel should be placed in the first 128MiB of RAM. It is recommended
that it is loaded above 32MiB in order to avoid the need to relocate
prior to decompression, which will make the boot process slightly
faster.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cosmetic cleanup in mach-stm32mp Kconfig
- remove duplicated SPL_DRIVERS_MISC_SUPPORT
- update help for TARGET_STM32MP1
- set value for NR_DRAM_BANKS
- remove one comment as DEBUG_UART is deactivated by default
- include board Kconfig at the end of the file
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- export the function get_bootmode() and reused it in spl code
- manage uart instance by alias (prepare v4.19 binding)
- solve issue on nand instance
- restore console for uart boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As BSEC is secure aware, all register access need to be done
by TF-A for TRUSTED boot chain, when U-Boot is executed in
normal world.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Pbias voltage should match the IO voltage set for the SD card. With the
latest pbias change to 3.3V, update the capabilities and IO voltages
settings to 3.3V.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
As per recent TRM[1], PBIAS cell on dra7 devices supports
3.3v and not 3.0v as documented earlier.
Update PBIAS regulator max voltage and the voltage written
in the driver to reflect this.
[1] http://www.ti.com/lit/pdf/sprui30
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
When booting the am3517-evm, the following message appears:
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
This patch implements spl_start_uboot to clear this message
and allow device to know if it should boot U-Boot or kernel.
Fixes: 1c6b6f383a ("ARM: am3517_evm: Enable Falcon Mode")
Signed-off-by: Adam Ford <aford173@gmail.com>
The ISW_ENTRY_ADDR Kconfig option under mach-omap2 isn't a SoC specific
notion but rather "where is our previous stage loaded in memory?"
option. Make use of this on ARCH_KEYSTONE rather than SPL_TEXT_BASE for
our HS builds that are not using SPL anyhow.
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com?
Update VCI string to keep it compatible with legacy test setups.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL
is enabled. Use static platdata instead to save space.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The ofdata_to_platdata function should not be called if OF_CONTROL is
not enabled because fdtdec_* calls will fail. Block the function with
OF_CONTROL
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
ti_cm_get_macid() is used to get a syscon node from the dt, read the
efuse address and then assign the macid read from the address. Divide
these two steps into separate functions one of which can be called from
ofdata_to_platdata() while the other can be called from _probe(). This
ensures that platdata can be assigned statically in a board file when
OF_CONTROL is not enabled. Also add a macid_sel_compat in private data
to get information about the macid byte placement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Convert cpsw_platform_data to a pointer in cpsw_priv. Allocate it
dynamically and assign it as a part of eth_pdata. This helps in
isolating platform data handling and implementing platdata for SPL
in a board file.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
cpsw_phy_sel() is a configuration step that should not be in
ofdata_to_platdata(). Add phy_sel_compat to the cpsw_platform_data
structure so that it is accessible in _probe. Then move the call of
cpsw_phy_sel() to _probe.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
When initializing DDR from R5 SPL trigger U-Boot's panic facility
rather than simply returning from the board init function as there
is little point continuing code execution. Further, as panic implies
a board reset, so using it might potentially allow to recover from
this error in certain cases such as when the init failure was caused
by a temporary glitch of some sorts.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain parts of msmc sram can be used by DMSC or can be
marked as L3 cache. Since the available size can vary, changing
DT every time the size varies might be painful. So, query this
information using TISCI cmd and fixup the DT for kernel.
Fixing up DT does the following:
- Create a sram node if not available
- update the reg property with available size
- update ranges property
- loop through available sub nodes and delete it if:
- mentioned size is out if available range
- subnode represents l3 cache or dmsc usage.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DMSC can use certain amount of msmc memory available in the
system. Also certain part of msmc memory can be marked as L3
cache using board config. But users might not know what size
is being used and the remaining available msmc memory. In order
to fix this TISCI protocol provides a messages that can query
the available msmc memory in the system. Add support for this
message.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that NAND is supported on DRA71x include various NAND environment
settings
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If SW 8 pins 0 and 1 indicate that NAND should be enabled then
the pins pinmux must be reconfigured for NAND mode.
Therefore, enable NAND by reconfiguring the pinmux.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
By default VOUT3 occupies the pins required for NAND. Therefore, create
a seperate entry that can be use to reconfigure these pins to work for
NAND.
On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
enabled or not. For NAND to be selected pin 0 should be on and pin 1
should be off. Any other combination will assume NAND shouldn't be
enabled.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.
This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.
Signed-off-by: Adam Ford <aford173@gmail.com>
When booting using an SPL on am335x, if we want to support booting with
the boot ROM loader via USB (which uses RNDIS, making bootp and tftp
calls) we need to enable gadget eth in the SPL to load the main U-Boot
image. To enable CONFIG_SPL_ETH_SUPPORT, we must enable
CONFIG_SPL_ENV_SUPPORT as the environment is used by the eth support, but
we don't actually need to have environment variables saved in the SPL
environment. We do however have environment variables saved in the main
U-Boot image and enable CONFIG_ENV_OFFSET_REDUND (we are storing in raw
NAND). In such instances, even with the build config enabling both
CONFIG_CMD_SAVEENV and CONFIG_CMD_NAND, these options aren't set when
building the SPL, but CONFIG_ENV_OFFSET_REDUND still is.
Don't check this configuration option for SPL builds to enable the above
configuration.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration for the MT41K128M16JT125K memory modules as used on the
Bosch Guardian device.
Based on a patch by:
Govindaraji Sivanantham <Govindaraji.Sivanantham@in.bosch.com>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
[checkpatch.pl cleanup by Martyn Welch]
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
AM57xx IDK EVMs can boot out of QSPI. Enable configs to support QSPI
boot. Also enable configs for updating QSPI boot images over DFU.
Tested on AM572x IDK EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds dt node for DP83867 phy used on K2G ICE board and
also enable netcp device nodes for the board.
EVM hardware spec recommends to add 0.25 nsec delay in the tx
direction and 2.25 nsec delay in the rx direction for internal
delay in the clock path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
1. Unfortunately, the phy data manual disallows this. Add
ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
enable workaround suggested for this incorrect strap setting. This
ensures proper operation of this PHY.
The dts bindings are kept in sync with that from 4.14.y linux
kernel. This required the pinmux device related bindings to be
commented out to allow for compilation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable ti phy dp83867 for k2g
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch removes the unused phy-mode property from the phy dt node. On
K2G, currently link-interface determines if phy is used or not and is
already set to use rgmii. So this is not needed. Besides phy-mode should
be added to slave interface configuration of the cpsw driver, not in the
phy node.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
