Commit graph

70894 commits

Author SHA1 Message Date
Patrick Delaunay
b2f6b97b78 fastboot: add command to select the default emmc hwpart for boot
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:

$> fastboot oem partconf:<boot_ack> <boot_partition>

The partition_access argument is forced to 0 (userdata)

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[lukma - Kconfig adjustments after merging this patch]
2021-02-07 19:22:55 +01:00
Patrick Delaunay
3acbc7b2aa fastboot: mmc: extend flash/erase for both emmc hwpart 1 and 2
Update the code and the configs for eMMC boot and userdata
partitions acces
- FASTBOOT_MMC_BOOT_SUPPORT: boot partition 1 and 2 (erase/write)
- FASTBOOT_MMC_BOOT1_NAME: boot partition 1, default name="mmc0boot0"
- FASTBOOT_MMC_BOOT2_NAME: boot partition 2, default name="mmc0boot1"

This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-02-07 19:22:55 +01:00
Patrick Delaunay
7596696bc5 fastboot: mmc: Add CONFIG_FASTBOOT_MMC_USER_SUPPORT
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).

The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME

This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-02-07 19:22:55 +01:00
Roman Kovalivskyi
a362ce214f fastboot: Implement generic fastboot_set_reboot_flag
It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.

If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.

Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
2021-02-07 19:22:54 +01:00
Roman Kovalivskyi
f80798122a Revert "fastboot: Add default fastboot_set_reboot_flag implementation"
This reverts commit 0ebf9842e5.

Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.

Next commit introduces new generic implementation of
fastboot_set_reboot_flag.

Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
2021-02-07 19:22:54 +01:00
Heinrich Schuchardt
a045bc18d6 dfu: dfu_sf: use correct print code
For printing unsigned int %u has to be used.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-07 19:22:54 +01:00
Tom Rini
8308a28af8 Merge tag 'ti-v2021.04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
2021-02-05 09:39:31 -05:00
Tom Rini
55ffabec7f Pull request for UEFI sub-system for efi-2021-04-rc2
Bug fixes:
 
 * do not allow creating of files with filenames on FAT file system
 * install UEFI System Partition GUID on ESP handle
 * in dtbdump.efi test tool use GUID to find ESP handle
 
 Documentation:
 
 * man-page for load command
 * describe end of life of plat_auto
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmAcTmoACgkQxIHbvCwF
 GsT0ag/6AjtRtGd8ySYix9lytmDphyztvTTHrd/Bz+UWi64iEIOH6t/RIAPG0yb0
 WJBvTe9eGxbNx5VOx426YtPUGFfzAakMyRaAL5Y4wkQsKgseq3q2sE55wzG4nTiR
 nmweR7TPslSkGtqQQehGGtdMJn//M/alABtTQs5eyjOkJPEc4DzATeksfA64t2Dj
 ijaU4dWbKVHy8spz3xH9cIdF1fvCJGxvSvXCVculN5bfgCf/MJYq6gb2VgXyLL1w
 +6GNklzNKRY8Lk9C4hqq2ktK4dQ4R0qKgqxtihwuSdbZmhV6cScKvmNPCqdYx/1l
 p5ywE067KRm16Hl/41QhKPMVleqn33Td3U4I+CWvO9DPnsH7pY9iRymM6zfRm9+j
 nO4f8++OqG/YXL+oABLkSIZaoYWqGmZd5Nc1bq9sTXthUXHZeC6/V19n0TJYVIV5
 HtIPFJbqn4S4uKjTFxyvudE6OfeW4+HpsY7bQHDRXWY1Kma0fgMYbhFZdUeNyr+6
 N8EFXZ5nKVWqLH9zlAIPOn0AEXzOfvsWad+NU0bILY8f60SqW0AydjvzG8z9CU3e
 vqxx+NxcG26SYscIcANvMI7HxtB6mblBYF2vSqBAkSrQ23Om+dnKkLhHO8pkkNtn
 J4rLpAxEAA1yaqKK/1n67D6pSqvjdWQqOfgL/3E1sqgAGYYOBrc=
 =rQaL
 -----END PGP SIGNATURE-----

Merge tag 'efi-2021-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi

Pull request for UEFI sub-system for efi-2021-04-rc2

Bug fixes:

* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle

Documentation:

* man-page for load command
* describe end of life of plat_auto
2021-02-04 17:35:50 -05:00
Heinrich Schuchardt
5489448cd7 doc: dm: describe end of life of plat_auto
Describe when plat_auto is freed.

Fix a typo.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-04 20:36:07 +01:00
Heinrich Schuchardt
4038c6e848 doc: return value exception command
If the exception cannot be raised, the command returns.
Currently the return values are not all the same.

Remove the sub-chapter 'Return value'

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-04 20:36:06 +01:00
Heinrich Schuchardt
f074209ce9 doc: describe load command
Man-page for load command.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-02-04 20:36:06 +01:00
Heinrich Schuchardt
02fc018a35 efi_loader: VenMedia device path node
The Load File2 protocol exposes a device path with a VenMedia() node. Hence
our implementation of the device path to text protocol should support this
node.

Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-04 20:12:41 +01:00
Heinrich Schuchardt
6bca36cee2 efi_selftest: use GUID to find ESP in dtbdump
If dtbdump.efi is loaded from memory when calling LoadImage the loaded
image protocol will not indicate the partition from where it was loaded.
In this case use the EFI system partition for the 'load' and 'save'
commands.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-04 20:09:03 +01:00
Heinrich Schuchardt
b9b0ea30c7 efi_loader: install UEFI System Partition GUID
On the handle for the UEFI System Partition we must install the System
Partition GUID (with a NULL interface).

Let the efidebug command display the GUID.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-04 20:09:02 +01:00
Heinrich Schuchardt
1bc9fc3483 efi_loader: only check size if EFI_DT_APPLY_FIXUPS
In the implementation of the EFI_DT_FIXUP_PROTOCOL:

* Only check the buffer size when EFI_DT_APPLY_FIXUPS is set.
* In this case the field totalsize of the device-tree may not exceed the
  buffer size.
* Install device-tree only if EFI_DT_INSTALL_TABLE is set.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2021-02-04 20:09:02 +01:00
Lokesh Vutla
6239cc8c4e arm: dts: k3-j7200: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J7200 related v5.11-rc6 Linux kernel dts into U-Boot.
MCU R5F nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid regressions, r5f nodes are kept intact.
These will be added in kernel in future.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-02-04 20:37:57 +05:30
Lokesh Vutla
70e167495a arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-02-04 20:37:57 +05:30
Lokesh Vutla
e497876343 arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot
Sync all AM65 related v5.11-rc6 Linux kernel dts into U-Boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
489274eb6c configs: am65x_evm: Add configs for UHS modes
Add configs for voltage switching and UHS modes for the SD card
and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
9aa4302c02 arm: dts: k3-am654-base-board: Limit Sd card to High speed modes
There's an issue with the base board in which the power cycle
circuit takes way longer to power down than expected by mmc core.
code. This prevents the card from enumerating in UHS modes.

Disable UHS modes for this board until a new board revision fixes
the issue.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
0758e9fe3f arm: dts: k3-am65-main: Add itapdly and clkbuf-sel values
Add the appropriate itapdly and clkbuf-sel values required for
some lower speed modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
79a30b1128 configs: j7200_evm: Add support for UHS modes
Add configs to support UHS modes for the SD card and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
d1d34f7985 configs: j721e_evm: Add support for UHS modes
Add configs to support UHS modes for the SD card and HS200 for the eMMC.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
b4e85ca0ba arm: dts: k3-j7200-common-proc-board: Enable support for UHS modes
Add support for UHS modes by adding the regulators to power cycle
and voltage switch the card. Also add pinmuxes required for each
node

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
f695347066 arm: dts: k3-j7200-main: Add support for gpio0
Add support for the main_gpio0 node

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
f0a496a3d2 arm: dts: k3-j721e-common-proc-board: Add support for UHS modes for SD card
Add support for regulators to power cycle and switch IO voltage to the
SD card. This enables support for UHS modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
52de3c324d arm: dts: k3-j721e-main: Update otap-delay values
Update otap delay values to match with the latest Data Manual[1].

[1] https://www.ti.com/lit/gpn/dra829v

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
2121c7e2d5 arm: dts: k3-am65: Fix mmc nodes
Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts

This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode

While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
e9fbbba4e3 mmc: am654_sdhci: Use sdhci_set_control_reg()
Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
27a87c834f mmc: am654_sdhci: Fix HISPD bit configuration in some lower speed modes
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.

To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.

Use the sdhci writeb callback to implement this condition.

[1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
a759abf569 mmc: am654_sdhci: Add support for software tuning
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.

[1] https://www.ti.com/lit/pdf/spract9

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
194c3756c8 mmc: am654_sdhci: Add support for writing to clkbuf_sel
Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
c964447ea3 mmc: am654_sdhci: Add support for input tap delay
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.

Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
8c32b5f370 mmc: am654_sdhci: Add support for AM65x SR2.0
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
5b29fd4a8d mmc: am654_sdhci: Add flag for PHY calibration
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.

Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
144e131d47 mmc: am654_sdhci: Convert flag fields to BIT macro
Convert the flags field defines to use the BIT() macro.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
c604e204ef mmc: am654_sdhci: Unconditionally switch off DLL in the beginning of ios_post()
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
43392b550e mmc: sdhci: Add helper functions for UHS modes
Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-02-04 20:37:57 +05:30
Dario Binacchi
bfefa3a4eb configs: am335x_evm: enable CONFIG_SPL_ALLOC_BD
With commit 38d6b7ebda ("spl: Drop bd_info in the data section") you
need to enable this option to boot from mmc.

Signed-off-by: Dario Binacchi <dariobin@libero.it>
2021-02-04 20:37:56 +05:30
Suman Anna
468ec2f3ef remoteproc: k3_r5: Sync to upstreamed kernel DT property names
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.

The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
  lockstep-mode => ti,cluster-mode
  atcm-enable   => ti,atcm-enable
  btcm-enable   => ti,btcm-enable
  loczrama      => ti,loczrama

Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.

Signed-off-by: Suman Anna <s-anna@ti.com>
2021-02-04 20:37:56 +05:30
Aswath Govindraju
59a51c3076 configs: am65x_evm_a53: Enable config for phandle check while getting sequence number
AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.

Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:56 +05:30
David Lechner
2ea852c69f configs: legoev3: disable non-Linux boot options
This disables booting to non-Linux OSes.

This board is uncomfortably close to its 256K size limit, so every
few KB saved helps.

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
David Lechner
b228f0295d configs: legoev3: disable CONFIG_NET
This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.

This also fixes the warning:

===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
David Lechner
f4e2c10a71 ARM: legoev3: drop bi_arch_number
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
David Lechner
68432b5d12 ARM: legoev3: set serial# env var
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.

Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).

Signed-off-by: David Lechner <david@lechnology.com>
2021-02-04 20:37:56 +05:30
Pali Rohár
64fd2d2614 Nokia RX-51: Convert to CONFIG_DM_MMC
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2021-02-04 20:37:56 +05:30
Tom Rini
21cb717e79 Support late device removal
Allow booting a 32-bit system with a top memory address beyond 4 GiB
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmAbVFARHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebn/Af9FoJksV/0G+z6AzjJ20+yoOVAOFFhUkFB
 UTW5m0Sv3wMmlSNdg0+DPuB3o04U6RwlZTdIqK/shc0fEqr0YeJgWAEPSMjQH0xc
 ou8S9LAnJNrvlqNu5aP2Wq5KFwOxp/ODx5RBNpiSaL+m26dmUi2eeU+Ym996rr06
 +m0qycZP07BHLIfm0pWyZjAI2+VzR7Uuyd1pKEIerOTRkAvZzk6pQbs+vv6PLaHa
 Wcl9grnoO3pDZt6CYpmgv8mbetXteRfrdYMsu2OiHx/2nU3pa7TbOoNcuA2ww2Ko
 u9NL7s0E0Y1LY6/QNb1O7eGOxcR1H5y/19K6NGrK27BwMkrvb0GKRg==
 =jMvm
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-3feb21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm

Support late device removal
Allow booting a 32-bit system with a top memory address beyond 4 GiB
2021-02-04 08:19:23 -05:00
Tom Rini
67472aa059 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Fix broken multi-core boot for QEMU x86
- Add zboot support to boot x86 Linux kernel image in the PXE sysboot
  utility
2021-02-04 08:18:57 -05:00
Kory Maincent
18c2582183 cmd: pxe_utils: sysboot: Add zboot support to boot x86 Linux kernel image
Add "zboot" command to the list of supported boot in the
label_boot function.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add component tags in the summary]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2021-02-03 23:16:44 +08:00
Kory Maincent
ff0287ec28 cmd: pxe_utils: Replace ifdef by IS_ENABLED
Replace all the macro ifdef by IS_ENABLED.

All of these configs are set in the defconfig files and not in the
include board headers files.

Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: keep the preprocessor case unchanged]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2021-02-03 23:16:36 +08:00