This patch got dropped during the update of DTs to 4.14, re-add it
back. This adds reset GPIOs to the ethernet PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These do not need to be available early on Gen3 , so move them to
the respective DT files.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add SDHI nodes to r8a77965.dtsi to get eMMC and SD slots operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add xHCI node to r8a77965.dtsi to get xHCI USB operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add generic EHCI nodes to r8a77965.dtsi to get EHCI USB operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add RAVB node to r8a77965.dtsi to get ethernet operational.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the R8A77965 M3N DT from Linux 4.16-rc1 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the placeholder DTS for R8A7790 H2 Stout with a proper
DTS from Linux next .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit d695d66278 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:
U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0
Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So 0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.
Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff
So, Fix the TEXT_BASE for proper aligned address 0xff704000
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
These were dropped in [1], after relocation, for their values offset by
reloc_off.
Unconditionally show the HW values and add a '(reloc)' hint for the
offset values showed after relocation.
Also, the LRs' dumps are now formatted the same way the other regs' are.
[1] Commit 082693f4 ("arm64 :show_regs: show the address before relocation")
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.
Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.
Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.
Fixes: a93fbf4a78 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently SPL_LOAD_FIT is unable to boot from nand on
i.MX6QDL platform, so enable only for MMC boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. DCD should not be present in images that will be verified
by software using HAB RVT authentication APIs. Newer versions of HAB
will generate an error if a DCD pointer is present in an image being
authenticated by calling the HAB RVT API. Older versions of HAB will
process and run DCD if it is present, and this could lead to an incorrect
authentication boot flow.
It is highly recommended this check is in place to ensure additional HAB
verified images do not include a DCD table.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently it is not possible to run CMD_DEK on i.MX SPL targets:
=> dek_blob 0x12000000 0x12001000 128
The system hangs after running dek_blob because the CAAM clock is being
disabled by the HAB code. There is no need to disable CAAM clock after
authenticating additional boot images, thus keep CAAM clock enabled to
address this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The UHS modes are not supported in beagle-x15 because it's not possible to
switch the IO lines supply voltage to 1.8v.
Also HS200 cannot be supported on mmc2, because the IO lines of mmc2 are
connected to 3.3v.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the new compatible string "ti,dra7-hsmmc" that was specifically
added for dra7 and dra72. This is required since for dra7 and dra72
processors iodelay values has to be set unlike other processors.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Enable I2C6 bus on Porter to access the PMIC , ie. to reset the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
