Leave only detected flash type enabled in FTD as otherwise GPMC CS is
claimed (and never freed) by Linux, causing 'concurent' flash type
not to be probed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
ISEE's U-Boot and Linux are using 1bit ECC scheme, while we
switched to 8bit ECC to fullfill flash specification requirements.
However when trying to run U-Boot on board with 1bit ECC'd data
on flash, UBI code takes several minutes to pass scan as reading
of every block ends with ecc error (which is also printed on
console).
So, until proper solution is developed, disable environment
alltogether.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
This is a 96Board compliant board based on STiH410 SoC:
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- SATA
- HDMI
- 2 x USB2.0 type A
- 1 x USB2.0 type micro-AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Low speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add SDHCI host controller found on STMicroelectronics SoCs
On some ST SoCs, i.e. STiH407/STiH410, the MMC devices can live
inside a dedicated flashSS sub-system that provides an extend subset
of registers that can be used to configure the Arasan MMC/SD Host
Controller.
This means, that the SDHCI Arasan Controller can be configured to be
eMMC4.5 or 4.3 spec compliant.
W/o these settings the SDHCI will configure and use the MMC/SD
controller with limited features e.g. PIO mode, no DMA, no HS etc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
As no gpio.h is defined in arch/arm/include/asm/arch-stih410,
to avoid compilation failure, do not include asm/arch/gpio.h.
This is needed for example when including sdhci.h, which include
asm/gpio.h>.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP
is common across other STMicroelectronics SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The STiH410 is an advanced multi-HD AVC processor with 3D
graphics acceleration and 1.5-GHz ARM Cortex-A9 SMP CPU
part of the STiH407 family.
It has wide connectivity including USB 3.0, PCI-e, SATA
and gigabit ethernet.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The SysTick is a 24-bit down counter that is found on all ARM Cortex
M3, M4, M7 devices and is always located at a fixed address.
The number of reference clock ticks that correspond to 10ms is normally
defined in the SysTick Calibration register's TENMS field. However, on some
devices this is wrong, so this driver allows the clock rate to be defined
using CONFIG_SYS_HZ_CLOCK.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
The size field in GP header that is expected by ROM is size of the
image + size of the header. But omapimage generates a gp header
only with size of the image as size field. Fix it
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards with OMAP3530 SoC fail to boot since commit bd2c4522c2
("ti: armv7: enable EXT support in SPL (using ti_armv7_common.h)")
because it enabled the use of Thumb2 for the SPL.
Experiments have shown that the deadlock happens in the
prcm_init() function from 'arch/arm/mach-omap2/omap3/clock.c'.
This patch enforces the compilation of clock.c source file in
ARM mode and makes the deadlock disappear. We are yet to figure
out the root cause of the problem. Still this is somewhat
better than having non-bootable boards for years.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Borrowing from omap3_logic, switch to SPL_SYS_MALLOC_SIMPLE and moving
the stack to DDR as soon as we're able.
Signed-off-by: Tom Rini <trini@konsulko.com>
Raw uboot image is used in place of FIT image in secure boot.
The maximum allocated size of raw u-boot bin is 1MB in memory map.
Hence , CONFIG_SYS_MONITOR_LEN has been modified to 1 MB.
The bootscript (BS_ADDR) and its header (BS_HDR_ADDR) offset on
MMC have also been modified to accommodate the increase in uboot size.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different
Add new function adjust_vdd() for LSCH3 compliant SoCs
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove the DDR interactive debugging to reduce the size of spl image.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Read DMA operations causes CRC error on armv8 chassis 2 platforms
due to the erratum A-010635.
In order to support sata on these platforms, ECC needs to be disabled.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In early MMU table, DDR has to be mapped as device memory to avoid
speculative access. After DDR is initialized, it needs to be updated
to normal memory to allow code execution. To simplify the code,
dram_init() is moved into a common file as a weak function.
Signed-off-by: York Sun <york.sun@nxp.com>
Function mmu_change_region_attr() is added to change existing mapping
with updated PXN, UXN and memory type. This is a break-before-make
process during which the mapping becomes fault (invalid) before final
attributres are set.
Signed-off-by: York Sun <york.sun@nxp.com>
Early MMU improves performance especially on emulators. However, the
early MMU is left enabled after the first stage of SPL boot. Instead
of flushing D-cache and dealing with re-enabling MMU for the second
stage U-Boot, disabling it for SPL build simplifies the process. The
performance penalty is unnoticeable on the real hardware. As of now,
SPL boot is not supported by existing emulators. So this should have
no impact on emulators.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch follows the break-before-make process when making changes
to MMU table. MMU is disabled before changing TTBR to avoid any
potential race condition.
Signed-off-by: York Sun <york.sun@nxp.com>
Update mapping with actual DDR size. Non-existing memory should not
be mapped as "normal" memory to avoid speculative access.
Signed-off-by: York Sun <york.sun@nxp.com>
Since the reserved RAM is tracked by gd->arch.resv_ram, calculation
of MC memory blocks can be simplified. The MC RAM is guaranteed to be
aligned by the reservation process.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.
Signed-off-by: York Sun <york.sun@nxp.com>
Instead of adding all memory banks, add a hook so individual SoC/board
can has its own implementation.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alexander Graf <agraf@suse.de>
Reviewed-by: Alexander Graf <agraf@suse.de>
Fix warnings reported when built with W=1, by DTC 1.4.2 or later:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linux Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated") declared that skeleton.dtsi was deprecated.
Move the memory node below to suppress warnings of FDTGREP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 04cd4e7215 ("ARM: uniphier: remove DRAM base address from
board parameters") accidentally unset the DRAM_SPARSE flag, and
changed the physical map of the DRAM channels. Revive the original
behavior.
Fixes: 04cd4e7215 ("ARM: uniphier: remove DRAM base address from board parameters")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Shunji Sato <sato.shunji@socionext.com>
Some initialization was unintentionally being skipped on omap5.
Fixes: f5af0827f2 ("arm: omap-common: Guard some parts of the code with CONFIG_OMAP44XX/OMAP54XX")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This tool does not work with Python 3. Change the shebang to make sure the
script is run by a Python 2 interpreter.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Currently nandecc returns zero even if underlaying
omap_nand_switch_ecc function fails. Fix that by
propagating error returned to command return value.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This moves all of the current ARM errata from various header files and in to
Kconfig. This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config. We now just select these once at the higher level in Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the default y options under arch/arm/mach-omap2/omap4/Kconfig to be
using imply instead in arch/arm/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the default y options under arch/arm/mach-omap2/omap3/Kconfig to be
using imply instead in arch/arm/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
The option that we had set in board/ti/common/Kconfig as default y are
best done with imply under the appropriate main Kconfig option instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
These particular SPL options are part of what the ROM provides, but for
compatibility with how we have previously used them, move them to being
implied by the board being selected.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently upstream does not yet understand the imply keyword. For what
we use kconfiglib.py for today, this is OK. We only need to be able to
evaluate in order to make boards.cfg and none of those choices will
depend on how imply evaluates out.
Signed-off-by: Tom Rini <trini@konsulko.com>
