Official DT bindings use compatible string marvell,armada-3700-ehci.
Update drivers and DTS files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
In commit d368e10705 ("phy: marvell: a3700: Convert to official DT
bindings in COMPHY driver") was done update to official DT bindings but
compatible string of official DT bindings was not updated.
Fix it now.
Fixes: d368e10705 ("phy: marvell: a3700: Convert to official DT bindings in COMPHY driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The changes introduced with commit 6337d53fdf ("arm: dts: sync am33xx
with Linux 5.9-rc7") prevent the PDU001 from operating correctly.
This patch fixes the configuration of the pin multiplexer and uart3.
Signed-off-by: Felix Brack <fb@ltec.ch>
EMIF tool for AM64 SK is now updated to 0.8.0 that includes
* disabled Write DQ training
* improve CA ODT to 60 ohms
The lpddr4 enabled with periodic WDQ training is causing periodic 26us
stall. This makes the SoC stall without doing anything which leads to
R5 interrupt latency in TCM memory. Due to this periodic training there
are some outstanding CPU transactions waiting for the lpddr4 to complete.
Hence, disable the periodic write DQ training during the
non-initialization stage of lpddr4 which results in an approximate 1us
stall. Also, update the lpddr4 config to improve CA ODT by 60 ohms
The rationales are as follows:
- PI_WDQLVL_EN: 2 Bits register field to support write DQ leveling,
disable bit 1 that supports Write DQ during non-initialization to
avoid ~26us stall during code execution.
- MR11_DATA_F1/F2_x register fields value changed to 0x66 that changes
the CA ODT from 48ohm to 60ohm to improve the eye margin on CA bus by
increasing the signal swing.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".
The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.
A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".
nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f6853 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PLL_CMNLC clocks are modelled as a child clock device of seirra. In the
function device_probe, the corresponding clocks are probed before calling
the device's probe. The PLL_CMNLC mux clock can only be created after the
device's probe. Therefore, move assigned-clocks and assigned-clock-parents
to the link nodes in U-Boot device tree file.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
J721S2 can support two instances for DDR. Therefore, add the device support
for the same and use 4266MT/s as DDR frequency.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.
Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
A System on Module (SoM) contains the SoC, PMIC, DDR and basic high speed
components necessary for functionality. Therefore, add support for the
components present on the SoM.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The J721S2 SoC belongs to the K3 Multicore SoC architecture platform,
providing advanced system integration in automotive ADAS applications and
industrial applications requiring AI at the network edge. This SoC extends
the Jacinto 7 family of SoCs with focus on lowering system costs and power
while providing interfaces, memory architecture and compute performance for
single and multi-sensor applications.
Some highlights of this SoC are:
* Dual Cortex-A72s in a single cluster, three clusters of lockstep capable
dual Cortex-R5F MCUs, Deep-learning Matrix Multiply Accelerator(MMA), C7x
floating point Vector DSP.
* 3D GPU: Automotive grade IMG BXS-4-64
* Vision Processing Accelerator (VPAC) with image signal processor and
Depth and Motion Processing Accelerator (DMPAC)
* Two CSI2.0 4L RX plus one eDP/DP, two DSI Tx, and one DPI interface.
* Two Ethernet ports with RGMII support.
* Single 4 lane PCIe-GEN3 controllers, USB3.0 Dual-role device subsystems,
* Up to 20 MCANs, 5 McASP, eMMC and SD, OSPI/HyperBus memory controller,
QSPI, I3C and I2C, eCAP/eQEP, eHRPWM, MLB among other peripherals.
* Hardware accelerator blocks containing AES/DES/SHA/MD5 called SA2UL
management.
See J721S2 Technical Reference Manual (SPRUJ28 – NOVEMBER 2021)
for further details: http://www.ti.com/lit/pdf/spruj28
Introduce basic support for the J721S2 SoC.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update to the 5.16 imx8mq dts files and dt bindings
Changes since v1:
Dropped rfkill.h that is not in linux mainline yet.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the PCIe support on i.MX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux 854a4766ac12 ("arm64: dts: imx8mm: Add the pcie support")
Add the PCIe PHY support on iMX8MM platforms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Pick from Linux b9ec888f636f ("arm64: dts: imx8mm: Add the pcie phy support")
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319c3 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Marek Vasut <marex@denx.de> # Picked from Linux 5cfad4f45806f ("arm64: dts: imx8mm/q: Fix pad control of SD1_DATA0")
With the updated device tree's having USB support, enable in
U-Boot. This also requires the addition of the imx8m power
domain, since the USB is gated by the power domain controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Resync the SOM and baseboar files with the device trees that will
be included in 5.17-RC1 when it's cut. This will improve pinmuxing
for USDHC1 and add USB functionality.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rather than using odd implicit blob-ext naming, explicitly specify the
type to be of blob-ext and therefore also simplify the node naming.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Some of the nodes were named using a underscore, so rectify this and
consistenly use dashes.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
When using a board variant that selects the lvds specific dtb the
*.u-boot.dtsi file will not be included. To have a lvds dtb specific
u-boot.dtsi file move this part to a common board u-boot.dtsi file and
include this in the board base u-boot.dtsi and create an additional one
for the lvds variant.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Synchronize DH DHCOM DTs with Linux commit 25960cafa06e ("Linux 5.15.12").
There is no functional change to the resulting DTs. The imx6qdl-dhcom-pdk2.dtsi
had to be adjusted with additional headers, gpio.h, pwm.h, input.h, else
the DT cannot be compiled, the same change is likely necessary in Linux.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add labels to remaining anatop regulators, so their supplies can be
assigned in board DTs. This is similar to Linux kernel commit
93385546ba369 ("ARM: dts: imx6qdl-sabresd: Assign corresponding power supply for LDOs")
except it does not contain the unrelated sabresd changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Now the dts information corresponds to the one available in the kernel.
With this patch applied the 'mtd list' shows proper names and
offsets for MTD partitions.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
According to the i.MX6ULL Reference Manual, pad CSI_DATA07 may
have the ESAI_TX0 functionality, not ESAI_T0.
Also, NXP's i.MX Config Tools 10.0 generates dtsi with the
MX6ULL_PAD_CSI_DATA07__ESAI_TX0 naming, so fix it accordingly.
There are no devicetree users in mainline that use the old name,
so just remove the old entry.
Fixes: f8ca22b8de ("arm: dts: imx6ull: add pinctrl defines")
Reported-by: George Makarov <georgemakarov1@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The PDK2 board is capable of running both 100M and 1G ethernet. However,
the i.MX6 has only one ethernet MAC, so it is possible to configure
either 100M or 1G Ethernet. In case of 100M option, the PHY is on the
SoM and the signals are routed to a RJ45 port. For 1G the PHY is on
the PDK2 board with another RJ45 port. 100M and 1G ethernet use
different signal pins from the i.MX6, but share the MDIO bus.
This SoM board combination is used to demonstrate how to enable 1G
ethernet configuration.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
The FXL6408 GPIO expander manages critical devices,
including on-module USB hub. Configure the expander to
switch the USB hub into bypass mode, allowing to use
on-carrier-board USB hub.
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Add device tree files for suniv and
Lichee Pi Nano it is a board based on F1C100s.
dt-bindings/dts are synced with 5.16.0
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The commit in the Fixes: tag below broke traffic through switch ports
where the SERDES protocol requires in-band autoneg and this requirement
isn't described in the device tree: SGMII, QSGMII, USXGMII (with
2500Base-X, in-band autoneg isn't supported).
The LS1028A-QDS boards are not yet ready for syncing their device trees
with Linux, since Ethernet is missing there (but has been submitted):
https://lore.kernel.org/lkml/20211112223457.10599-11-leoyang.li@nxp.com/
When agreement is reached for the Ethernet support in Linux, there will
be a sync for these boards as well. For now, just enable in-band autoneg
to fix the breakage.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow device trees to be reused between Linux and U-Boot.
The source for these device trees is linux-next as of commit
bd8a9cd624c6 ("arm64: dts: ls1028a-rdb: update copyright"), which was
chosen because some changes needed to be done to the Linux DTs too,
before they could be shared:
https://lore.kernel.org/linux-arm-kernel/20211202141528.2450169-5-vladimir.oltean@nxp.com/T/#m6f63c92e75fa79a01144b2c2c6dc4776e7971395
There are two more commits on the RDB device tree which haven't been
picked up yet, because they have dependencies on the SoC device tree:
dd3d936a1b17 ("arm64: dts: ls1028a: add ftm_alarm1 node to be used as wakeup source")
b2e2d3e02fb6 ("arm64: dts: ls1028a-rdb: enable pwm0")
These will be picked up on the next resync.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reuse the scheme implemented by the Kontron SL28 boards in
commit d08011d7f9
("arm: dts: ls1028a: disable the PCIe controller by default")
and move the 'status = "okay"' lines for the PCIe controllers
inside a separate U-Boot dtsi for the LS1028A-RDB board. This way, the
existing Linux device tree can simply be dropped in.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no I2C peripheral on these buses on the reference design board,
and the Linux device tree does not enable them either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is no SPI peripheral on the LS1028A-RDB, therefore no reason to
enable these nodes in the U-Boot device tree (and Linux does not enable
them either).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In a bit of a blunder, the blamed commit in the Fixes: tag below made
the mscc_felix switch driver look at the 'managed = "in-band-status"'
device tree property, forgetting that the U-Boot device tree had not
been updated to include that property, whereas the Linux one does.
The switch is therefore described in the device tree as not requiring
in-band autoneg, but the PHY driver for VSC8514 (drivers/net/phy/mscc.c)
still enables that feature. This results in a mismatch => no traffic.
This patch is a copy-paste of the Ethernet device tree nodes from Linux,
which resolves that issue. The device tree update also renames the
Ethernet PHY labels.
Fixes: e3789a7262 ("net: dsa: felix: configure the in-band autoneg property based on OF node info")
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
